3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTMC2210ATJ+T
TRINAMIC Motion Control GmbH · Motor Driver ICs · TQFN-32-EP(5x5)
TMC2210ATJ+T from TRINAMIC Motion Control GmbH, in a TQFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IREF | input | Analog reference current input for current scaling; an external resistor to GND sets the full-scale current. |
| 2 | N.C. | unconnected | Not connected; keep open or connect to GND for additional cooling. |
| 3 | VDD1V8 | power_out | Output of the internal 1.8V regulator; attach a 2.2µF or larger ceramic capacitor to AGND near the pin. |
| 4 | AGND | power_in | Analog ground; connect to the ground plane. |
| 5 | VCC_IO | power_in | Digital IO supply voltage from an external source that defines the circuit IO level and is required for proper output voltage levels. |
| 6 | CFG6 | input | Configuration input for hold current reduction (with CFG7); has an internal pull-up and is referenced to VCC_IO. |
| 7 | CFG4 | input | Configuration input for digital current scale (GND = 75% of IRUN, VCC_IO = 100%); has an internal pull-up. |
| 8 | CFG5 | input | Configuration input selecting chopper mode (GND = SpreadCycle, VCC_IO = StealthChop2); has an internal pull-up. |
| 9 | DRV_ENN | input | Enable input; the power stage switches off with all motor outputs floating when driven high, and it has an internal pull-up. |
| 10 | CFG7 | input | Configuration input for hold current reduction (with CFG6); has an internal pull-down. |
| 11 | ERROR | output | Open-drain error output that requires an external pull-up resistor and is pulled low during the reset state. |
| 12 | INDEX | output | Open-drain index pulse output that marks microstep 0 position of coil B. |
| 13 | OV | output | Open-drain overvoltage indicator output with a fixed threshold; an external pull-up resistor is required. |
| 14 | CPI | passive | Charge pump capacitor input; tie to CPO using a 22nF 50V capacitor. |
| 15 | CPO | passive | Charge pump capacitor output that connects to CPI through a 22nF 50V capacitor. |
| 16 | VCP | power_out | Charge pump voltage; tie to VS using a 1.0µF capacitor with the positive end close to the VS pin. |
| 17 | VS | power_in | Motor supply voltage (4.5V to 36V); provide filtering capacitance near the pin with the shortest loop to GND. |
| 18 | OUT1B | output | Motor coil B output 1 of the H-bridge. |
| 19 | OUT2B | output | Motor coil B output 2 of the H-bridge. |
| 20 | VS | power_in | Motor supply voltage (4.5V to 36V); provide filtering capacitance near the pin with the shortest loop to GND. |
| 21 | VS | power_in | Motor supply voltage (4.5V to 36V); provide filtering capacitance near the pin with the shortest loop to GND. |
| 22 | OUT2A | output | Motor coil A output 2 of the H-bridge. |
| 23 | OUT1A | output | Motor coil A output 1 of the H-bridge. |
| 24 | VS | power_in | Motor supply voltage (4.5V to 36V); provide filtering capacitance near the pin with the shortest loop to GND. |
| 25 | SLEEPN | input | Active-low power-down and reset input; a continuous low level puts the device into sleep mode, and the pin is a high-voltage pin with an internal pull-down. |
| 26 | CFG3 | input | Configuration input for run current range (with CFG2); has an internal pull-up. |
| 27 | CFG2 | input | Configuration input for run current range (with CFG3); has an internal pull-up. |
| 28 | CFG1 | input | Configuration input for microstep resolution (with CFG0); has an internal pull-up. |
| 29 | CFG0 | input | Configuration input for microstep resolution (with CFG1). |
| 30 | N.C. | unconnected | Not connected; keep open or connect to GND for additional cooling. |
| 31 | STEP | input | STEP input referenced to VCC_IO; each active edge advances the motor by one step. |
| 32 | DIR | input | Direction input referenced to VCC_IO that sets the motor rotation direction. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | TRINAMIC Motion Control GmbH |
| Package | TQFN-32-EP(5x5) |
| Category | Power Management |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage Range | VS | 4.5 | 36 | V | 7 | ||
| Logic I/O Supply Voltage Range | VCC_IO | 2.2 | 5.5 | V | 8 | ||
| Input Leakage | InLeak | -1 | 1 | μA | Inputs without pullup/pulldown resistance | 8 | |
| Output Logic-Low Voltage | VOL | 0.4 | V | ILOAD = 5mA | 8 | ||
| Open-Drain Output Logic High Leakage Current | IOH | -1 | 1 | μA | V(PIN) = 5.5V | 8 | |
| Output Leakage | ILEAK | -5 | 5 | μA | 8 | ||
| SLEEPN Pulldown Input Resistance | RPDSLEEPN | 0.8 | 1.5 | MΩ | 8 | ||
| Internal Pullup/Pulldown Resistance | RPULL | 60 | 100 | 140 | kΩ | to GND or to VCC_IO | 8 |
| Output ON-Resistance Low Side | RONLS | 0.11 | 0.2 | Ω | CFG3/CFG2 = 10 | 8 | |
| Output ON-Resistance Low Side | RONLS | 0.15 | 0.28 | Ω | CFG3/CFG2 = 01 | 8 | |
| Output ON-Resistance Low Side | RONLS | 0.28 | 0.54 | Ω | CFG3/CFG2 = 00 | 8 | |
| Output ON-Resistance High Side | RONHS | 0.12 | 0.22 | Ω | 8 | ||
| Sleep Mode Current Consumption | IVS | 4 | 18 | μA | V(SLEEPN) = 0 | 7 | |
| Quiescent Current Consumption | IVS | 3.5 | 5 | mA | V(SLEEPN) = 1, V(DRV_ENN) = 1 | 8 | |
| Sleep Mode Current Consumption | IVCC_IO | 5 | 10 | μA | V(SLEEPN) = 0 | 8 | |
| Quiescent Current Consumption | IVCC_IO | 35 | 60 | μA | V(SLEEPN) = 1 | 8 | |
| Overcurrent Protection Blanking Time | TOCP | 0.9 | 1.5 | 2.3 | μs | 9 | |
| UVLO Threshold on VS | UVLO | 3.75 | 3.9 | 4.05 | V | VS falling | 9 |
| UVLO Threshold on VCC_IO | UVLO | 0.9 | 1.5 | 1.95 | V | VCC_IO falling | 9 |
| IREF Pin Resistor Range | RREF | 12 | 60 | kΩ | 9 | ||
| IREF Output Voltage | VREF | 0.882 | 0.9 | 0.918 | V | 9 | |
| Regulation Accuracy | DITRIP1 | -5 | 5 | % | Output current from 7% to 100% FS, RREF = 12kΩ | 9 | |
| Internal Clock Frequency | fCLK | 11.9 | 12.5 | 13.2 | MHz | min/max values take temperature coefficient into account | 9 |
| VS to GND | VS | -0.3 | 41 | V | to GND | 7 | |
| VCC_IO to GND | VCC_IO | -0.3 | 5.5 | V | to GND | 7 | |
| OV to GND | OV | -0.3 | 6 | V | to GND | 7 | |
| Operating Temperature Range | -40 | 125 | °C | 7 | |||
| Junction Temperature | 165 | °C | 7 | ||||
| Storage Temperature Range | -65 | 150 | °C | 7 | |||
| Soldering Temperature (reflow) | 260 | °C | 7 | ||||
| Thermal Resistance Junction to Ambient, Single-Layer Board | θJA | 47 | °C/W | TQFN32 5mm x 5mm | 7 | ||
| Thermal Resistance Junction to Case, Single-Layer Board | θJC | 1.7 | °C/W | TQFN32 5mm x 5mm | 7 | ||
| Thermal Resistance Junction to Ambient, Four-Layer Board | θJA | 29 | °C/W | TQFN32 5mm x 5mm | 7 | ||
| Thermal Resistance Junction to Case, Four-Layer Board | θJC | 1.7 | °C/W | TQFN32 5mm x 5mm | 7 |
CAD (KiCad official)
- Symbol:
TMC2210ATJ+T - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: TQFN-32-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
tmc2210atj-t-etched.step/tmc2210atj-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tmc2210atj-t.step/tmc2210atj-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: TRINAMIC Motion Control GmbH datasheet (29 pp, sha256
fada830a99c27888, retrieved 2026-10-27, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusoff(skipped (clean text read)), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).