Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TMC2210ATJ+T

TRINAMIC Motion Control GmbH · Motor Driver ICs · TQFN-32-EP(5x5)

TMC2210ATJ+T from TRINAMIC Motion Control GmbH, in a TQFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 IREF input Analog reference current input for current scaling; an external resistor to GND sets the full-scale current.
2 N.C. unconnected Not connected; keep open or connect to GND for additional cooling.
3 VDD1V8 power_out Output of the internal 1.8V regulator; attach a 2.2µF or larger ceramic capacitor to AGND near the pin.
4 AGND power_in Analog ground; connect to the ground plane.
5 VCC_IO power_in Digital IO supply voltage from an external source that defines the circuit IO level and is required for proper output voltage levels.
6 CFG6 input Configuration input for hold current reduction (with CFG7); has an internal pull-up and is referenced to VCC_IO.
7 CFG4 input Configuration input for digital current scale (GND = 75% of IRUN, VCC_IO = 100%); has an internal pull-up.
8 CFG5 input Configuration input selecting chopper mode (GND = SpreadCycle, VCC_IO = StealthChop2); has an internal pull-up.
9 DRV_ENN input Enable input; the power stage switches off with all motor outputs floating when driven high, and it has an internal pull-up.
10 CFG7 input Configuration input for hold current reduction (with CFG6); has an internal pull-down.
11 ERROR output Open-drain error output that requires an external pull-up resistor and is pulled low during the reset state.
12 INDEX output Open-drain index pulse output that marks microstep 0 position of coil B.
13 OV output Open-drain overvoltage indicator output with a fixed threshold; an external pull-up resistor is required.
14 CPI passive Charge pump capacitor input; tie to CPO using a 22nF 50V capacitor.
15 CPO passive Charge pump capacitor output that connects to CPI through a 22nF 50V capacitor.
16 VCP power_out Charge pump voltage; tie to VS using a 1.0µF capacitor with the positive end close to the VS pin.
17 VS power_in Motor supply voltage (4.5V to 36V); provide filtering capacitance near the pin with the shortest loop to GND.
18 OUT1B output Motor coil B output 1 of the H-bridge.
19 OUT2B output Motor coil B output 2 of the H-bridge.
20 VS power_in Motor supply voltage (4.5V to 36V); provide filtering capacitance near the pin with the shortest loop to GND.
21 VS power_in Motor supply voltage (4.5V to 36V); provide filtering capacitance near the pin with the shortest loop to GND.
22 OUT2A output Motor coil A output 2 of the H-bridge.
23 OUT1A output Motor coil A output 1 of the H-bridge.
24 VS power_in Motor supply voltage (4.5V to 36V); provide filtering capacitance near the pin with the shortest loop to GND.
25 SLEEPN input Active-low power-down and reset input; a continuous low level puts the device into sleep mode, and the pin is a high-voltage pin with an internal pull-down.
26 CFG3 input Configuration input for run current range (with CFG2); has an internal pull-up.
27 CFG2 input Configuration input for run current range (with CFG3); has an internal pull-up.
28 CFG1 input Configuration input for microstep resolution (with CFG0); has an internal pull-up.
29 CFG0 input Configuration input for microstep resolution (with CFG1).
30 N.C. unconnected Not connected; keep open or connect to GND for additional cooling.
31 STEP input STEP input referenced to VCC_IO; each active edge advances the motor by one step.
32 DIR input Direction input referenced to VCC_IO that sets the motor rotation direction.
33 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer TRINAMIC Motion Control GmbH
Package TQFN-32-EP(5x5)
Category Power Management
Pins 33

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage Range VS 4.5 36 V 7
Logic I/O Supply Voltage Range VCC_IO 2.2 5.5 V 8
Input Leakage InLeak -1 1 μA Inputs without pullup/pulldown resistance 8
Output Logic-Low Voltage VOL 0.4 V ILOAD = 5mA 8
Open-Drain Output Logic High Leakage Current IOH -1 1 μA V(PIN) = 5.5V 8
Output Leakage ILEAK -5 5 μA 8
SLEEPN Pulldown Input Resistance RPDSLEEPN 0.8 1.5 MΩ 8
Internal Pullup/Pulldown Resistance RPULL 60 100 140 kΩ to GND or to VCC_IO 8
Output ON-Resistance Low Side RONLS 0.11 0.2 Ω CFG3/CFG2 = 10 8
Output ON-Resistance Low Side RONLS 0.15 0.28 Ω CFG3/CFG2 = 01 8
Output ON-Resistance Low Side RONLS 0.28 0.54 Ω CFG3/CFG2 = 00 8
Output ON-Resistance High Side RONHS 0.12 0.22 Ω 8
Sleep Mode Current Consumption IVS 4 18 μA V(SLEEPN) = 0 7
Quiescent Current Consumption IVS 3.5 5 mA V(SLEEPN) = 1, V(DRV_ENN) = 1 8
Sleep Mode Current Consumption IVCC_IO 5 10 μA V(SLEEPN) = 0 8
Quiescent Current Consumption IVCC_IO 35 60 μA V(SLEEPN) = 1 8
Overcurrent Protection Blanking Time TOCP 0.9 1.5 2.3 μs 9
UVLO Threshold on VS UVLO 3.75 3.9 4.05 V VS falling 9
UVLO Threshold on VCC_IO UVLO 0.9 1.5 1.95 V VCC_IO falling 9
IREF Pin Resistor Range RREF 12 60 kΩ 9
IREF Output Voltage VREF 0.882 0.9 0.918 V 9
Regulation Accuracy DITRIP1 -5 5 % Output current from 7% to 100% FS, RREF = 12kΩ 9
Internal Clock Frequency fCLK 11.9 12.5 13.2 MHz min/max values take temperature coefficient into account 9
VS to GND VS -0.3 41 V to GND 7
VCC_IO to GND VCC_IO -0.3 5.5 V to GND 7
OV to GND OV -0.3 6 V to GND 7
Operating Temperature Range -40 125 °C 7
Junction Temperature 165 °C 7
Storage Temperature Range -65 150 °C 7
Soldering Temperature (reflow) 260 °C 7
Thermal Resistance Junction to Ambient, Single-Layer Board θJA 47 °C/W TQFN32 5mm x 5mm 7
Thermal Resistance Junction to Case, Single-Layer Board θJC 1.7 °C/W TQFN32 5mm x 5mm 7
Thermal Resistance Junction to Ambient, Four-Layer Board θJA 29 °C/W TQFN32 5mm x 5mm 7
Thermal Resistance Junction to Case, Four-Layer Board θJC 1.7 °C/W TQFN32 5mm x 5mm 7

CAD (KiCad official)

  • Symbol: TMC2210ATJ+T
  • Footprint: Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm
  • 3D model: TQFN-32-EP(5x5) (KiCad packages3D, STEP)
  • 3D model files: tmc2210atj-t-etched.step / tmc2210atj-t-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tmc2210atj-t.step / tmc2210atj-t.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: TRINAMIC Motion Control GmbH datasheet (29 pp, sha256 fada830a99c27888, retrieved 2026-10-27, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus off (skipped (clean text read)), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF