3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMPQ2019GN-33-Z
Monolithic Power Systems · Linear Voltage Regulators (LDO) · SOIC-8-EP
MPQ2019GN-33-Z from Monolithic Power Systems, in a SOIC-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | power_out | Regulated output voltage; only a low-value ceramic capacitor (≥ 0.47µF) on the output is required for stability. |
| 2 | NC | unconnected | No connection. |
| 3 | GND | power_in | Ground; connect the exposed pad and GND to the same ground plane. |
| 4 | IN | power_in | Input voltage; connect a 3V to 40V supply to IN (absolute maximum IN is -0.3V to +42V). |
| 5 | EN | input | Regulator on/off control input; logic low (below 0.3V) shuts down the IC and logic high (above 1.8V) starts it up, and EN can be connected to IN for automatic start-up. |
| 6 | PG | output | Power good open-drain output; it should be pulled up to VOUT or an external source (<15V) through a resistor, and if not used it can be left floating. |
| 7 | PGDL | passive | Programmable power-good delay time pin, where a capacitor sets the PG delay time (CPGDL = 47nF gives 5 to 15 ms); if not used it can be left floating. |
| 8 | FB | input | Feedback input for the output-adjustable version; FB is regulated to 1.25V nominally and is used to set the output voltage through an external resistor divider. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | SOIC-8-EP |
| Category | Power Management |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VIN | 3 | 40 | V | 3 | ||
| Output Voltage | VOUT | 1.25 | 15 | V | 3 | ||
| Operating Temperature | TA | -40 | 125 | °C | TA≤TJ≤+150°C | 3 | |
| IN, EN voltage (absolute maximum) | -0.3 | 42 | V | 3 | |||
| OUT voltage (absolute maximum) | -0.3 | 17 | V | 3 | |||
| PG voltage (absolute maximum) | -0.3 | 15 | V | 3 | |||
| PGDL, FB voltage (absolute maximum) | -0.3 | 6 | V | 3 | |||
| Junction Temperature (absolute maximum) | 150 | C | 3 | ||||
| Lead Temperature (absolute maximum) | 260 | C | 3 | ||||
| Storage Temperature | -65 | 150 | C | 3 | |||
| ESD HBM (Human Body Model) | 4 | kV | 3 | ||||
| ESD MM (Machine Model) | 200 | V | 3 | ||||
| GND Current | IGND | 12 | 16 | µA | 0<ILOAD<1mA | 4 | |
| GND Current | IGND | 16 | 22 | µA | 1mA<ILOAD<30mA | 4 | |
| GND Current | IGND | 65 | 95 | µA | 30mA<ILOAD<300mA | 4 | |
| Shutdown Supply Current | IS | 1 | µA | VEN =0V | 4 | ||
| Load-Current Limit | ILIMIT | 600 | 1000 | 1350 | mA | VIN=7V, VOUT = 0V, TA = +25°C | 4 |
| Output Voltage Accuracy (MPQ2019GN-33) | 3.2 | 3.3 | 3.4 | V | ILOAD=5mA | 4 | |
| Dropout Voltage (MPQ2019GN-33) | VDROPOUT | 230 | 430 | mV | VOUT=3.3V, ILOAD = 150mA | 4 | |
| Dropout Voltage (MPQ2019GN-33) | VDROPOUT | 480 | 640 | mV | TA = +25°C, VOUT=3.3V, ILOAD = 300mA | 4 | |
| Line Regulation (MPQ2019GN-33) | -10 | 1 | 10 | mV | VIN = 5V to 40V, ILOAD = 5mA, VOUT = 3.3V | 4 | |
| Load Regulation (MPQ2019GN-33) | 1 | 15 | mV | ILOAD = 5mA to 300mA, VOUT = 3.3V, TA = +25°C | 5 | ||
| Start-Up Response Time (MPQ2019GN-33) | 0.5 | 1 | ms | RLOAD=500Ω, VOUT=3.3V, COUT=22µF, VOUT from 10% to 90% | 5 | ||
| EN Threshold Voltage, low | VIL | 0.3 | V | 5 | |||
| EN Threshold Voltage, high | VIH | 1.8 | V | 5 | |||
| EN Input Current | 0.1 | 0.5 | µA | EN = 0V or 15V | 5 | ||
| PG Rising Threshold (MPQ2019GN-33) | 88 | 92 | 96 | %VFB | 5 | ||
| PG Low Voltage | 0.1 | 0.4 | V | Sink 1mA Current | 5 | ||
| PG Leakage Current | 1 | µA | VPG=5V | 5 | |||
| PGDL Charging Current | 3 | 5.5 | 9 | µA | VPGDL=1V | 5 | |
| PGDL Rising Threshold | 1.4 | 1.7 | 2 | V | 5 | ||
| PGDL Falling Threshold | 0.2 | 0.4 | 0.7 | V | 5 | ||
| PG Delay Time | 5 | 10 | 15 | ms | CPGDL=47nF | 5 | |
| PG Reaction Time | 0.5 | 2 | µs | CPGDL=47nF | 5 | ||
| Thermal Resistance, junction-to-ambient, SOIC-8 EP | θJA | 50 | C/W | Note 5: JESD51-7, 4-layer PCB | 3 | ||
| Thermal Resistance, junction-to-case, SOIC-8 EP | θJC | 10 | C/W | Note 5: JESD51-7, 4-layer PCB | 3 | ||
| Thermal Shutdown | TSD | 165 | C | 5 | |||
| Thermal Shutdown Hysteresis | ΔTSD | 30 | C | 5 | |||
| PG Rising Threshold Hysteresis | 5 | %VFB | 5 |
CAD (KiCad official)
- Symbol:
MPQ2019GN-33-Z - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm - 3D model: SOIC-8-EP (KiCad packages3D, STEP)
- 3D model files:
mpq2019gn-33-z-etched.step/mpq2019gn-33-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mpq2019gn-33-z.step/mpq2019gn-33-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (16 pp, sha256
f44bb2fb5f1e768b, retrieved 2026-10-28, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).