component
F280045PMSR
Public Made by Adomby adom
Texas Instruments Microcontroller Units (MCUs/MPUs/SOCs), LQFP-64(10x10). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownF280045PMSR
Texas Instruments · Microcontroller Units (MCUs/MPUs/SOCs) · LQFP-64(10x10)
F280045PMSR from Texas Instruments, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GPIO29 | bidirectional | General-purpose I/O 29 with mux options SCIA_TX, EPWM7_B, OUTPUTXBAR6, EQEP1_B, SD1_C3, EQEP2_INDEX, LINA_RX, SPIB_STE and ERRORSTS. |
| 2 | GPIO28 | bidirectional | General-purpose I/O 28 with mux options SCIA_RX, EPWM7_A, OUTPUTXBAR5, EQEP1_A, SD1_D3, EQEP2_STROBE, LINA_TX, SPIB_CLK and ERRORSTS. |
| 3 | XRSn | bidirectional | Device reset input and watchdog reset open-drain output with internal pull-up; use a 2.2kΩ to 10kΩ resistor to VDDIO and at most 100nF to VSS. |
| 4 | VDD | power_in | 1.2V digital logic supply; about 20µF total decoupling near the VDD pins is recommended. |
| 5 | VSS | power_in | Digital ground. |
| 6 | A6,PGA5_OF | input | ADC-A input 6 / PGA-5 output filter (optional) / CMPSS-5 inputs / AIO228 digital input. |
| 7 | B2,C6,PGA3_OF | input | ADC-B input 2, ADC-C input 6, PGA-3 output filter (optional), CMPSS-3 inputs and AIO226 digital input. |
| 8 | B3,VDAC | input | ADC-B input 3 or optional external reference for on-chip DAC; fixed 100pF to VSSA, add at least 1µF if used as DAC reference. |
| 9 | A2,B6,PGA1_OF | input | ADC-A input 2, ADC-B input 6, PGA-1 output filter (optional), CMPSS-1 inputs and AIO224 digital input. |
| 10 | PGA1_GND,PGA3_GND,PGA5_GND | input | Ground reference for PGA-1, PGA-3 and PGA-5; tie to VSSA if unused. |
| 11 | C4,PGA5_IN | input | ADC-C input 4 / PGA-5 input / CMPSS-5 inputs / AIO239 digital input. |
| 12 | C0,PGA1_IN | input | ADC-C input 0 / PGA-1 input / CMPSS-1 inputs / AIO237 digital input. |
| 13 | C2,PGA3_IN | input | ADC-C input 2 / PGA-3 input / CMPSS-3 inputs / AIO244 digital input. |
| 14 | A1,DACB_OUT | bidirectional | ADC-A input 1 or buffered DAC-B output; also AIO232 digital input. |
| 15 | A0,B15,C15,DACA_OUT | bidirectional | ADC-A input 0, ADC-B input 15, ADC-C input 15 or buffered DAC-A output; also AIO231 digital input. |
| 16 | VREFHIA,VREFHIB,VREFHIC | bidirectional | ADC-A/B/C high reference voltage, driven externally or by the device; place at least 2.2µF to the VREFLO pin and do not load externally. |
| 17 | VREFLOA,VREFLOB,VREFLOC | input | ADC-A/B/C low reference voltage; tie to VSSA if unused. |
| 18 | C1,PGA2_IN | input | ADC-C input 1 / PGA-2 input / CMPSS-2 inputs / AIO238 digital input. |
| 19 | C3,PGA4_IN | input | ADC-C input 3 / PGA-4 input / CMPSS-4 inputs / AIO245 digital input. |
| 20 | PGA2_GND,PGA4_GND,PGA6_GND | input | Ground reference for PGA-2, PGA-4 and PGA-6; tie to VSSA if unused. |
| 21 | VSSA | power_in | Analog ground. |
| 22 | VDDA | power_in | 3.3V analog supply; place at least 2.2µF to VSSA on each pin. |
| 23 | A4,B8,PGA2_OF | input | ADC-A input 4, ADC-B input 8, PGA-2 output filter (optional), CMPSS-2 inputs and AIO225 digital input. |
| 24 | B4,C8,PGA4_OF | input | ADC-B input 4, ADC-C input 8, PGA-4 output filter (optional), CMPSS-4 inputs and AIO227 digital input. |
| 25 | A10,B1,C10,PGA7_OF | input | ADC-A input 10, ADC-B input 1, ADC-C input 10, CMPSS-7 inputs and AIO230 digital input (no PGA function on 64-pin package). |
| 26 | VSS | power_in | Digital ground. |
| 27 | VDD | power_in | 1.2V digital logic supply. |
| 28 | VDDIO | power_in | 3.3V digital I/O supply; place at least 0.1µF decoupling on each pin. |
| 29 | GPIO13 | bidirectional | General-purpose I/O 13 with mux options EPWM7_B, CANB_RX, EQEP1_INDEX, SCIB_RX, PMBUSA_ALERT and FSIRXA_CLK. |
| 30 | GPIO12 | bidirectional | General-purpose I/O 12 with mux options EPWM7_A, CANB_TX, EQEP1_STROBE, SCIB_TX, PMBUSA_CTL and FSIRXA_D0. |
| 31 | GPIO11 | bidirectional | General-purpose I/O 11 with mux options EPWM6_B, SCIB_RX, OUTPUTXBAR7, EQEP1_B, SPIA_STE and FSIRXA_D1. |
| 32 | GPIO33 | bidirectional | General-purpose I/O 33 with mux options I2CA_SCL, SPIB_STE, OUTPUTXBAR4, LINA_RX, SD1_C3, FSIRXA_CLK and CANA_RX. |
| 33 | GPIO16 | bidirectional | General-purpose I/O 16 with mux options SPIA_SIMO, CANB_TX, OUTPUTXBAR7, EPWM5_A, SCIA_TX, SD1_D1, EQEP1_STROBE, PMBUSA_SCL and XCLKOUT. |
| 34 | GPIO17 | bidirectional | General-purpose I/O 17 with mux options SPIA_SOMI, CANB_RX, OUTPUTXBAR8, EPWM5_B, SCIA_RX, SD1_C1, EQEP1_INDEX and PMBUSA_SDA. |
| 35 | GPIO24 | bidirectional | General-purpose I/O 24 with mux options OUTPUTXBAR1, EQEP2_A, EPWM8_A, SPIB_SIMO, SD1_D1, PMBUSA_SCL, SCIA_TX and active-low ERRORSTS. |
| 36 | TCK | input | JTAG test clock with internal pull-up. |
| 37 | GPIO37/TDO | bidirectional | GPIO37 defaulting to JTAG TDO; tri-stated without JTAG activity, so enable internal pull-up or add external pull-up. |
| 38 | TMS | bidirectional | JTAG test mode select with internal pull-up; add an external pull-up (2.2kΩ recommended) to VDDIO; no TRSTn pin exists. |
| 39 | GPIO35/TDI | bidirectional | GPIO35 defaulting to JTAG TDI; enable internal pull-up or add external pull-up to avoid a floating input. |
| 40 | GPIO32 | bidirectional | General-purpose I/O 32 with mux options I2CA_SDA, SPIB_CLK, EPWM8_B, LINA_TX, SD1_D3, FSIRXA_D0 and CANA_TX. |
| 41 | GPIO18_X2 | bidirectional | GPIO18 or crystal oscillator output X2; GPIO use only when clocked by INTOSC with an external pull-down (1kΩ recommended) on X1. |
| 42 | X1 | bidirectional | Crystal oscillator or single-ended 3.3V clock input; tie to VSS if unused. |
| 43 | VDDIO | power_in | 3.3V digital I/O supply; place at least 0.1µF decoupling on each pin. |
| 44 | VDD | power_in | 1.2V digital logic supply. |
| 45 | VSS | power_in | Digital ground. |
| 46 | VREGENZ | input | Internal regulator enable with internal pull-down; tie to VSS to enable internal VREG or to VDDIO to use external 1.2V supply. |
| 47 | GPIO8 | bidirectional | General-purpose I/O 8 with mux options EPWM5_A, CANB_TX, ADCSOCAO, EQEP1_STROBE, SCIA_TX, SPIA_SIMO, I2CA_SCL and FSITXA_D1. |
| 48 | GPIO4 | bidirectional | General-purpose I/O 4 with mux options EPWM3_A, OUTPUTXBAR3, CANA_TX and FSIRXA_CLK. |
| 49 | GPIO3 | bidirectional | General-purpose I/O 3 with mux options EPWM2_B, OUTPUTXBAR2, PMBUSA_SCL, SPIA_CLK, SCIA_RX and FSIRXA_D0. |
| 50 | GPIO2 | bidirectional | General-purpose I/O 2 with mux options EPWM2_A, OUTPUTXBAR1, PMBUSA_SDA, SCIA_TX and FSIRXA_D1. |
| 51 | GPIO1 | bidirectional | General-purpose I/O 1 with mux options EPWM1_B and I2CA_SCL. |
| 52 | GPIO0 | bidirectional | General-purpose I/O 0 with mux options EPWM1_A and I2CA_SDA. |
| 53 | VDDIO_SW | power_in | 3.3V supply for internal DC-DC regulator with 20µF bulk input capacitor; must connect to VDDIO and share the same supply. |
| 54 | GPIO23_VSW | bidirectional | GPIO23 or internal DC-DC switching output VSW; about 100pF internal capacitance, so avoid for fast switching use. |
| 55 | VSS_SW | power_in | Internal DC-DC regulator ground; always connect to VSS. |
| 56 | GPIO22_VFBSW | bidirectional | GPIO22 or internal DC-DC feedback VFBSW; connect to the node where L(VSW) meets the VDD rail when DC-DC is used. |
| 57 | GPIO7 | bidirectional | General-purpose I/O 7 with mux options EPWM4_B, OUTPUTXBAR5, EQEP1_B, CANB_RX, SPIB_SIMO and FSITXA_CLK. |
| 58 | VSS | power_in | Digital ground. |
| 59 | VDD | power_in | 1.2V digital logic supply. |
| 60 | VDDIO | power_in | 3.3V digital I/O supply; place at least 0.1µF decoupling on each pin. |
| 61 | GPIO5 | bidirectional | General-purpose I/O 5 with mux options EPWM3_B, OUTPUTXBAR3, CANA_RX, SPIA_STE and FSITXA_D1. |
| 62 | GPIO9 | bidirectional | General-purpose I/O 9 with mux options EPWM5_B, SCIB_TX, OUTPUTXBAR6, EQEP1_INDEX, SCIA_RX, SPIA_CLK and FSITXA_D0. |
| 63 | GPIO10 | bidirectional | General-purpose I/O 10 with mux options EPWM6_A, CANB_RX, ADCSOCBO, EQEP1_A, SCIB_TX, SPIA_SOMI, I2CA_SDA and FSITXA_CLK. |
| 64 | GPIO6 | bidirectional | General-purpose I/O 6 with mux options EPWM4_A, OUTPUTXBAR4, SYNCOUT, EQEP1_A, CANB_TX, SPIB_SOMI and FSITXA_D0. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | LQFP-64(10x10) |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| I/O supply voltage (VDDIO) absolute maximum | VDDIO | -0.3 | 4.6 | V | referenced to VSS | 59 | |
| Analog supply voltage (VDDA) absolute maximum | VDDA | -0.3 | 4.6 | V | referenced to VSSA | 59 | |
| Core supply voltage (VDD) absolute maximum | VDD | -0.3 | 1.5 | V | referenced to VSS | 59 | |
| Input voltage absolute maximum | VIN | -0.3 | 4.6 | V | (3.3V) | 59 | |
| Output voltage absolute maximum | VO | -0.3 | 4.6 | V | 59 | ||
| Digital input clamp current per pin | IIK | -20 | 20 | mA | VIN < VSS or VIN > VDDIO | 59 | |
| Natural ventilation operating temperature | TA | -40 | 125 | °C | 59 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 59 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 59 | ||
| Device supply voltage VDDIO and VDDA with internal BOR disabled | VDDIO, VDDA | 2.8 | 3.3 | 3.63 | V | internal BOR disabled | 60 |
| Device supply voltage VDD | VDD | 1.14 | 1.2 | 1.32 | V | 60 | |
| Junction temperature, S version | TJ | -40 | 125 | °C | S version | 60 | |
| High-level input voltage (3.3V) | VIH | 2 | V | (3.3V); maximum printed as VDDIO + 0.3 | 68 | ||
| Low-level input voltage (3.3V) | VIL | 0.8 | V | (3.3V); minimum printed as VSS - 0.3 | 68 | ||
| Input hysteresis | VHYSTERESIS | 150 | mV | 68 | |||
| Low-level output voltage | VOL | 0.4 | V | IOL = IOL max | 68 | ||
| Low-level output voltage | VOL | 0.2 | V | IOL = 100µA | 68 | ||
| Pin leakage current | ILEAK | 2 | µA | all GPIO except GPIO23_VSW; pull-ups and outputs disabled; 0V ≤ VIN ≤ VDDIO | 68 | ||
| Input capacitance, digital GPIO | CI | 2 | pF | all digital GPIO except GPIO23_VSW | 68 | ||
| Internal regulator output voltage | VVREG | 1.14 | 1.2 | 1.32 | V | 81 | |
| Junction-to-case thermal resistance (PZ package) | RΘJC | 7.6 | °C/W | 69 | |||
| Junction-to-board thermal resistance (PZ package) | RΘJB | 24.2 | °C/W | 69 | |||
| Junction-to-ambient thermal resistance (high-K PCB) | RΘJA | 46.1 | °C/W | 0 lfm | 69 | ||
| Junction-to-package top thermal characterization | PsiJT | 0.2 | °C/W | 0 lfm | 69 | ||
| Junction-to-board thermal characterization | PsiJB | 23.8 | °C/W | 0 lfm | 69 |
CAD (KiCad official)
- Symbol:
F280045PMSR - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
f280045pmsr-etched.step/f280045pmsr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);f280045pmsr.step/f280045pmsr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (270 pp, sha256
f0eccdafc7ec75fa, retrieved 2026-11-10, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).