Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

S25FL128SAGMFIR00

Cypress Semicon · Pre-ordered Products · SOIC-16

S25FL128SAGMFIR00 from Cypress Semicon, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, read twice and the reads agreed); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 HOLD#/IO3 bidirectional Pauses serial communication without deselecting the device in single or dual mode, and acts as IO3 in Quad mode; it has an internal pull-up and may be left unconnected if Quad is not used.
2 VCC power_in Core power supply for all internal logic, 2.7 V to 3.6 V.
3 RESET# input Hardware reset input: LOW resets the device to Standby state; it has an internal pull-up and may be left unconnected if not used.
4 DNU unconnected Do Not Use: internal test connection with an internal pull-down; leave unconnected or tie to VSS and do not connect any host signal.
5 DNU unconnected Do Not Use: internal test connection with an internal pull-down; leave unconnected or tie to VSS and do not connect any host signal.
6 RFU unconnected Reserved for future use: no internal signal is currently connected, and it should not be used for PCB routing.
7 CS# input Chip Select: LOW enables the device and HIGH deselects it, ignoring inputs and putting outputs in high impedance.
8 SO/IO1 bidirectional Serial data output on the falling edge of SCK in single-bit mode, and IO1 for Dual or Quad commands.
9 WP#/IO2 bidirectional Write Protect when not in Quad mode and IO2 in Quad mode; it has an internal pull-up and may be left unconnected if Quad is not used.
10 VSS power_in Common ground reference for the device core, input receivers and output drivers.
11 DNU unconnected Do Not Use: internal test connection with an internal pull-down; leave unconnected or tie to VSS and do not connect any host signal.
12 DNU unconnected Do Not Use: internal test connection with an internal pull-down; leave unconnected or tie to VSS and do not connect any host signal.
13 NC unconnected Not connected: no internal signal is connected, and any signal routed to it must not exceed VIO.
14 VIO power_in Versatile I/O supply for input receivers and output drivers, range 1.65 V to VCC, and it cannot exceed VCC.
15 SI/IO0 bidirectional Serial input for instructions, addresses and data latched on the rising edge of SCK, and IO0 for Dual or Quad commands.
16 SCK input Serial clock that latches inputs on the rising edge, with SPI modes 0 and 3 supported.

Key specifications

Parameter Value
Manufacturer Cypress Semicon
Package SOIC-16
Category Electronic Tools/Instruments/Consumables
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input low voltage VIL -0.5 V 34
Input leakage current ILI -2 2 µA VCC = VCC Max, VIN = VIH or VIL 34
Output leakage current ILO -2 2 µA VCC = VCC Max, VIN = VIH or VIL 34
Active power supply current (READ) ICC1 16 mA Serial SDR@50 MHz; outputs unconnected during read data return 34
Active power supply current (READ) ICC1 33 mA Serial SDR@133 MHz; outputs unconnected during read data return 34
Active power supply current (READ) ICC1 50 mA Quad SDR@80 MHz; outputs unconnected during read data return 34
Active power supply current (READ) ICC1 61 mA Quad SDR@104 MHz; outputs unconnected during read data return 34
Active power supply current (READ) ICC1 75 mA Quad DDR@66 MHz; outputs unconnected during read data return 34
Active power supply current (READ) ICC1 90 mA Quad DDR@80 MHz; outputs unconnected during read data return 34
Active power supply current (Page program) ICC2 100 mA CS# = VIO 34
Active power supply current (WRR) ICC3 100 mA CS# = VIO 34
Active power supply current (SE) ICC4 100 mA CS# = VIO 34
Active power supply current (BE) ICC5 100 mA CS# = VIO 35
Standby current (Industrial) ISB 70 100 µA RESET#, CS# = VIO; SI, SCK = VIO or VSS, Industrial temperature 35
Input signal overshoot (negative) -2 V During voltage transitions, for periods up to 20 ns 32
Input rise and fall times 2.4 ns AC measurement conditions 37
Output short circuit current 100 mA No more than one output shorted to ground at a time; duration not greater than one second 31
Core supply voltage VCC (absolute maximum) VCC -0.5 4 V 31
Versatile I/O supply voltage VIO (absolute maximum) VIO -0.5 4 V VIO must always be less than or equal to VCC + 200 mV 31
Input voltage with respect to ground (VSS) -0.5 V Maximum is VIO + 0.5 V 31
Storage temperature (plastic packages) -65 150 °C 31
Ambient temperature with power applied -65 125 °C 31
Core supply voltage VCC (recommended) VCC 2.7 3.6 V 32
I/O supply voltage VIO (recommended) VIO 1.65 V Maximum is VCC + 200 mV 32
Ambient temperature (Industrial) TA -40 85 °C Industrial (I) grade 32
VCC (cut-off) low-power reinitialization threshold VCC (cut-off) 2.4 V VCC cut-off where re-initialization is needed 33
Power-up time to read operation tPU 300 µs VCC (min) to read operation 33
VCC low time for power-down tPD 15 µs VCC (low) time 33
Reset setup tRS 50 ns Prior reset end and RESET# HIGH before RESET# LOW 39
Reset pulse hold tRPH 35 µs RESET# LOW to CS# LOW 39
RESET# pulse width tRP 200 ns 39
Reset hold tRH 50 ns RESET# HIGH before CS# LOW 39
Input capacitance CIN 8 pF 1 MHz; applies to SCK, CS#, RESET# 38
Output capacitance COUT 8 pF 1 MHz; applies to all I/O 38
SCK clock frequency for READ and 4READ FSCK, R 50 MHz READ and 4READ instructions 40
SCK clock frequency for single commands FSCK, C 133 MHz Single commands as shown in Table 48 40
SCK clock frequency for dual and Quad commands FSCK, C 104 MHz DOR, 4DOR, QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR 40
SCK clock frequency for QPP and 4QPP FSCK, QPP 80 MHz QPP, 4QPP commands 40
CS# high time (Read instructions) tCS 10 ns Read instructions 40
CS# high time (Program/erase) tCS 50 ns Program/erase 40
CS# active setup time (relative to SCK) tCSS 3 ns 40
CS# active hold time (relative to SCK) tCSH 3 ns 40
Data in setup time tSU 1.5 3000 ns Maximum value only applies during Program/Erase Suspend/Resume commands 40
Data in hold time tHD 2 ns 40
Clock low to output valid tV 8 ns Full VCC range (2.7-3.6 V) and CL = 30 pF 40
Output hold time tHO 2 ns 40
Output disable time tDIS 0 8 ns 40
WP# setup time tWPS 20 ns Only applicable as a constraint for WRR when SRWD is set to 1 40
WP# hold time tWPH 100 ns Only applicable as a constraint for WRR when SRWD is set to 1 40
Thermal resistance junction to ambient (SO3016, 128 Mb) Theta JA 38 °C/W Still air (0 m/s), EIA/JESD51 31
Thermal resistance junction to board (SO3016, 128 Mb) Theta JB 19.7 °C/W 31
Thermal resistance junction to case (SO3016, 128 Mb) Theta JC 10.9 °C/W 31

CAD (KiCad official)

  • Symbol: S25FL128SAGMFIR00
  • Footprint: Package_SO:SOIC-16_3.9x9.9mm_P1.27mm
  • 3D model: SOIC-16 (KiCad packages3D, STEP)
  • 3D model files: s25fl128sagmfir00-etched.step / s25fl128sagmfir00-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); s25fl128sagmfir00.step / s25fl128sagmfir00.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Cypress Semicon datasheet (165 pp, sha256 3c5e0c26dfe26079, retrieved 2026-11-08, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF