Generated by kicad-footprint-generator · KiCad file format 20260206
S25FL128SAGMFIR00
Cypress Semicon · Pre-ordered Products · SOIC-16
S25FL128SAGMFIR00 from Cypress Semicon, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, read twice and the reads agreed); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | HOLD#/IO3 | bidirectional | Pauses serial communication without deselecting the device in single or dual mode, and acts as IO3 in Quad mode; it has an internal pull-up and may be left unconnected if Quad is not used. |
| 2 | VCC | power_in | Core power supply for all internal logic, 2.7 V to 3.6 V. |
| 3 | RESET# | input | Hardware reset input: LOW resets the device to Standby state; it has an internal pull-up and may be left unconnected if not used. |
| 4 | DNU | unconnected | Do Not Use: internal test connection with an internal pull-down; leave unconnected or tie to VSS and do not connect any host signal. |
| 5 | DNU | unconnected | Do Not Use: internal test connection with an internal pull-down; leave unconnected or tie to VSS and do not connect any host signal. |
| 6 | RFU | unconnected | Reserved for future use: no internal signal is currently connected, and it should not be used for PCB routing. |
| 7 | CS# | input | Chip Select: LOW enables the device and HIGH deselects it, ignoring inputs and putting outputs in high impedance. |
| 8 | SO/IO1 | bidirectional | Serial data output on the falling edge of SCK in single-bit mode, and IO1 for Dual or Quad commands. |
| 9 | WP#/IO2 | bidirectional | Write Protect when not in Quad mode and IO2 in Quad mode; it has an internal pull-up and may be left unconnected if Quad is not used. |
| 10 | VSS | power_in | Common ground reference for the device core, input receivers and output drivers. |
| 11 | DNU | unconnected | Do Not Use: internal test connection with an internal pull-down; leave unconnected or tie to VSS and do not connect any host signal. |
| 12 | DNU | unconnected | Do Not Use: internal test connection with an internal pull-down; leave unconnected or tie to VSS and do not connect any host signal. |
| 13 | NC | unconnected | Not connected: no internal signal is connected, and any signal routed to it must not exceed VIO. |
| 14 | VIO | power_in | Versatile I/O supply for input receivers and output drivers, range 1.65 V to VCC, and it cannot exceed VCC. |
| 15 | SI/IO0 | bidirectional | Serial input for instructions, addresses and data latched on the rising edge of SCK, and IO0 for Dual or Quad commands. |
| 16 | SCK | input | Serial clock that latches inputs on the rising edge, with SPI modes 0 and 3 supported. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Cypress Semicon |
| Package | SOIC-16 |
| Category | Electronic Tools/Instruments/Consumables |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input low voltage | VIL | -0.5 | V | 34 | |||
| Input leakage current | ILI | -2 | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 34 | |
| Output leakage current | ILO | -2 | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 34 | |
| Active power supply current (READ) | ICC1 | 16 | mA | Serial SDR@50 MHz; outputs unconnected during read data return | 34 | ||
| Active power supply current (READ) | ICC1 | 33 | mA | Serial SDR@133 MHz; outputs unconnected during read data return | 34 | ||
| Active power supply current (READ) | ICC1 | 50 | mA | Quad SDR@80 MHz; outputs unconnected during read data return | 34 | ||
| Active power supply current (READ) | ICC1 | 61 | mA | Quad SDR@104 MHz; outputs unconnected during read data return | 34 | ||
| Active power supply current (READ) | ICC1 | 75 | mA | Quad DDR@66 MHz; outputs unconnected during read data return | 34 | ||
| Active power supply current (READ) | ICC1 | 90 | mA | Quad DDR@80 MHz; outputs unconnected during read data return | 34 | ||
| Active power supply current (Page program) | ICC2 | 100 | mA | CS# = VIO | 34 | ||
| Active power supply current (WRR) | ICC3 | 100 | mA | CS# = VIO | 34 | ||
| Active power supply current (SE) | ICC4 | 100 | mA | CS# = VIO | 34 | ||
| Active power supply current (BE) | ICC5 | 100 | mA | CS# = VIO | 35 | ||
| Standby current (Industrial) | ISB | 70 | 100 | µA | RESET#, CS# = VIO; SI, SCK = VIO or VSS, Industrial temperature | 35 | |
| Input signal overshoot (negative) | -2 | V | During voltage transitions, for periods up to 20 ns | 32 | |||
| Input rise and fall times | 2.4 | ns | AC measurement conditions | 37 | |||
| Output short circuit current | 100 | mA | No more than one output shorted to ground at a time; duration not greater than one second | 31 | |||
| Core supply voltage VCC (absolute maximum) | VCC | -0.5 | 4 | V | 31 | ||
| Versatile I/O supply voltage VIO (absolute maximum) | VIO | -0.5 | 4 | V | VIO must always be less than or equal to VCC + 200 mV | 31 | |
| Input voltage with respect to ground (VSS) | -0.5 | V | Maximum is VIO + 0.5 V | 31 | |||
| Storage temperature (plastic packages) | -65 | 150 | °C | 31 | |||
| Ambient temperature with power applied | -65 | 125 | °C | 31 | |||
| Core supply voltage VCC (recommended) | VCC | 2.7 | 3.6 | V | 32 | ||
| I/O supply voltage VIO (recommended) | VIO | 1.65 | V | Maximum is VCC + 200 mV | 32 | ||
| Ambient temperature (Industrial) | TA | -40 | 85 | °C | Industrial (I) grade | 32 | |
| VCC (cut-off) low-power reinitialization threshold | VCC (cut-off) | 2.4 | V | VCC cut-off where re-initialization is needed | 33 | ||
| Power-up time to read operation | tPU | 300 | µs | VCC (min) to read operation | 33 | ||
| VCC low time for power-down | tPD | 15 | µs | VCC (low) time | 33 | ||
| Reset setup | tRS | 50 | ns | Prior reset end and RESET# HIGH before RESET# LOW | 39 | ||
| Reset pulse hold | tRPH | 35 | µs | RESET# LOW to CS# LOW | 39 | ||
| RESET# pulse width | tRP | 200 | ns | 39 | |||
| Reset hold | tRH | 50 | ns | RESET# HIGH before CS# LOW | 39 | ||
| Input capacitance | CIN | 8 | pF | 1 MHz; applies to SCK, CS#, RESET# | 38 | ||
| Output capacitance | COUT | 8 | pF | 1 MHz; applies to all I/O | 38 | ||
| SCK clock frequency for READ and 4READ | FSCK, R | 50 | MHz | READ and 4READ instructions | 40 | ||
| SCK clock frequency for single commands | FSCK, C | 133 | MHz | Single commands as shown in Table 48 | 40 | ||
| SCK clock frequency for dual and Quad commands | FSCK, C | 104 | MHz | DOR, 4DOR, QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR | 40 | ||
| SCK clock frequency for QPP and 4QPP | FSCK, QPP | 80 | MHz | QPP, 4QPP commands | 40 | ||
| CS# high time (Read instructions) | tCS | 10 | ns | Read instructions | 40 | ||
| CS# high time (Program/erase) | tCS | 50 | ns | Program/erase | 40 | ||
| CS# active setup time (relative to SCK) | tCSS | 3 | ns | 40 | |||
| CS# active hold time (relative to SCK) | tCSH | 3 | ns | 40 | |||
| Data in setup time | tSU | 1.5 | 3000 | ns | Maximum value only applies during Program/Erase Suspend/Resume commands | 40 | |
| Data in hold time | tHD | 2 | ns | 40 | |||
| Clock low to output valid | tV | 8 | ns | Full VCC range (2.7-3.6 V) and CL = 30 pF | 40 | ||
| Output hold time | tHO | 2 | ns | 40 | |||
| Output disable time | tDIS | 0 | 8 | ns | 40 | ||
| WP# setup time | tWPS | 20 | ns | Only applicable as a constraint for WRR when SRWD is set to 1 | 40 | ||
| WP# hold time | tWPH | 100 | ns | Only applicable as a constraint for WRR when SRWD is set to 1 | 40 | ||
| Thermal resistance junction to ambient (SO3016, 128 Mb) | Theta JA | 38 | °C/W | Still air (0 m/s), EIA/JESD51 | 31 | ||
| Thermal resistance junction to board (SO3016, 128 Mb) | Theta JB | 19.7 | °C/W | 31 | |||
| Thermal resistance junction to case (SO3016, 128 Mb) | Theta JC | 10.9 | °C/W | 31 |
CAD (KiCad official)
- Symbol:
S25FL128SAGMFIR00 - Footprint:
Package_SO:SOIC-16_3.9x9.9mm_P1.27mm - 3D model: SOIC-16 (KiCad packages3D, STEP)
- 3D model files:
s25fl128sagmfir00-etched.step/s25fl128sagmfir00-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);s25fl128sagmfir00.step/s25fl128sagmfir00.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Cypress Semicon datasheet (165 pp, sha256
3c5e0c26dfe26079, retrieved 2026-11-08, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).