3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownNCV4269AD150R2G
onsemi · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · SOIC-8
NCV4269AD150R2G from onsemi, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | I | power_in | Regulator input supply. Operating range 5.5 V to 45 V (5.0 V version), withstands +60 V transient and -40 V reverse. Connect to GND directly at the IC with a ceramic capacitor (typ. 0.1 μF to 470 nF). |
| 2 | SI | input | Sense Input to the on-chip voltage-monitor comparator. Typical threshold VSI,High = 1.31 V, VSI,Low = 1.20 V (bandgap-referenced); input current ±1 μA max. Drive from an external resistor divider off the monitored rail; if the sense function is not used, tie to Q. |
| 3 | RADJ | input | Reset Threshold Adjust. External resistor divider from Q to RADJ programs the reset trip point down from the default 4.65 V typ. to as low as 3.5 V (VRADJ,TH = 1.35 V typ.). Tie to GND when the adjustment function is not used to keep the default threshold. |
| 4 | D | passive | Reset Delay timing pin. Connect an external capacitor CD from D to GND to program the reset delay time td = CD·(VUD - VD,SAT)/ID,C (≈26 ms with 100 nF on the 5.0 V version, ID,C typ. 6.5 μA). Charges to VUD ≈1.8 V, discharges below VLD ≈0.45 V to assert reset. |
| 5 | GND | power_in | Device ground / signal return. All bypass capacitors reference this pin. |
| 6 | RO | output | Reset Output. Open-collector NPN with internal 20 kΩ (typ.) pull-up to Q; VRO,SAT ≤ 0.4 V. Driven low during power-up and any time VQ falls below VRT (4.65 V typ.) or the RADJ-programmed threshold; remains valid down to VQ = 1.0 V. Leave open if unused. |
| 7 | SO | output | Sense Output. Open-collector NPN with internal 20 kΩ (typ.) pull-up to Q; VSO,SAT ≤ 0.4 V. Goes low when SI drops below VSI,Low (1.20 V typ.) to give the microprocessor early warning of an impending reset. Leave open if unused. |
| 8 | Q | power_out | Regulated 5.0 V output (±2.0%) capable of 150 mA. Dropout 0.5 V max at 100 mA. Connect a 10 μF (min 2.2 μF) capacitor to GND with ESR < 10 Ω for stability; ceramic X7R (e.g. Murata GRM31CR71A106KA01) is acceptable with no minimum ESR. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOIC-8 |
| Category | PMIC |
| Pins | 8 |
Ordering variants
NCV4269AD150R2GD150GNCV4269AD150R2GNCV4269AD150R2GD133R2GNCV4269AD150R2GPD50GNCV4269AD150R2GPD50R2GNCV4269AD150R2GD250GNCV4269AD150R2GD250R2GNCV4269AD150R2GDW50GNCV4269AD150R2GDW50R2G
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage (5.0 V Version) | VQ | 4.9 | 5 | 5.1 | V | 1 mA ≤ IQ ≤ 100 mA, 6 V ≤ VI ≤ 16 V | 5 |
| Current Limit | IQ | 150 | 200 | 500 | mA | 5 | |
| Current Consumption; Iq = II – IQ | Iq | 190 | 250 | µA | IQ = 1 mA, RO, SO High | 5 | |
| Current Consumption; Iq = II – IQ | Iq | 250 | 450 | µA | IQ = 10 mA, RO, SO High | 5 | |
| Current Consumption; Iq = II – IQ | Iq | 2 | 3 | mA | IQ = 50 mA, RO, SO High | 5 | |
| Dropout Voltage (5.0 V Version) | Vdr | 0.25 | 0.5 | V | VI = 5 V, IQ = 100 mA | 5 | |
| Load Regulation | VQ | 10 | 20 | mV | IQ = 5 mA to 100 mA | 5 | |
| Line Regulation | VQ | 10 | 30 | mV | VI = 6 V to 26 V, IQ = 1 mA | 5 | |
| Reset Switching Threshold (5.0 V Version) | VRT | 4.5 | 4.65 | 4.8 | V | 5 | |
| Reset Adjust Switching Threshold (5.0 V Version) | VRADJ,TH | 1.26 | 1.35 | 1.44 | V | VQ > 3.5 V | 5 |
| Reset Pullup Resistance | RRO,INT | 10 | 20 | 40 | kΩ | 5 | |
| Reset Output Saturation Voltage | VRO,SAT | 0.1 | 0.4 | V | VQ < VRT, RRO, INT | 5 | |
| Upper Delay Switching Threshold (5.0 V Version) | VUD | 1.4 | 1.8 | 2.2 | V | 5 | |
| Lower Delay Switching Threshold (5.0 V Version) | VLD | 0.3 | 0.45 | 0.6 | V | 5 | |
| Saturation Voltage on Delay Capacitor | VD,SAT | 0.1 | V | VQ < VRT | 5 | ||
| Charge Current (5.0 V Version) | ID,C | 3 | 6.5 | 9.5 | µA | VD = 1 V | 5 |
| Delay Time L → H | td | 17 | 28 | 73 | ms | CD = 100 nF | 5 |
| Sense Threshold High | VSI,High | 1.24 | 1.31 | 1.38 | V | 5 | |
| Sense Threshold Low | VSI,Low | 1.16 | 1.2 | 1.28 | V | 5 | |
| Sense Output Saturation Voltage | VSO,Low | 0.1 | 0.4 | V | VSI < 1.20 V; VQ > 3 V; RSO | 5 | |
| Sense Resistor Pullup | RSO,INT | 10 | 20 | 40 | kΩ | 5 | |
| Sense Input Current | ISI | -1 | 0.1 | 1 | µA | 5 | |
| Input to Regulator | VI | -40 | 45 | V | 3 | ||
| Input Transient to Regulator | VI | 60 | V | 3 | |||
| Sense Input | VSI | -40 | 45 | V | 3 | ||
| Sense Input | ISI | -1 | 1 | mA | 3 | ||
| Reset Threshold Adjust | VRADJ | -0.3 | 7 | V | 3 | ||
| Reset Threshold Adjust | IRADJ | -10 | 10 | mA | 3 | ||
| Reset Delay | VD | -0.3 | 7 | V | 3 | ||
| Ground | Iq | 50 | mA | 3 | |||
| Reset Output | VRO | -0.3 | 7 | V | 3 | ||
| Sense Output | VSO | -0.3 | 7 | V | 3 | ||
| Regulated Output | VQ | -0.5 | 7 | V | 3 | ||
| Regulated Output | IQ | -10 | mA | 3 | |||
| Junction Temperature | TJ | 150 | °C | 3 | |||
| Storage Temperature | TSTG | -50 | 150 | °C | 3 | ||
| Input Voltage Operating Range (5.0 Version) | VI | 5.5 | 45 | V | 3 | ||
| Junction Temperature Operating Range | TJ | -40 | 150 | °C | 3 | ||
| Junction-to-Ambient Thermal Resistance (SO-8) | RθJA | 170.9 | °C/W | Note 4: 2 oz copper, 50 mm² copper area, 1.5 mm thick FR4 | 4 | ||
| Junction-to-Pin 4 Thermal Characterization (SO-8) | ΨJL4 | 53.8 | °C/W | Note 4: 2 oz copper, 50 mm² copper area, 1.5 mm thick FR4 | 4 |
CAD (KiCad official)
- Symbol:
NCV4269AD150R2G - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
ncv4269ad150r2g-etched.step/ncv4269ad150r2g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncv4269ad150r2g.step/ncv4269ad150r2g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (None pp, sha256
b38cb7c895a53288, retrieved 2026-08-17, tier: manufacturer) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.