Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MCP4262-103E

Microchip Tech · Pre-ordered MCUs · MSOP-10

MCP4262-103E from Microchip Tech, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CS input Chip select input: forcing CS to VIL enables serial commands and forcing it to VIHH enables high-voltage serial commands; the input is high-voltage tolerant with Schmitt trigger.
2 SCK input SPI serial clock input (high-voltage tolerant with Schmitt trigger), operating at up to 10 MHz per the SPI interface feature.
3 SDI input SPI serial data input, connected to the host controller SDO pin; high-voltage tolerant with Schmitt trigger.
4 VSS power_in Device ground reference; the electrical performance is specified relative to this pin.
5 P1B passive Potentiometer 1 terminal B of the second rheostat network, which may carry positive or negative current with voltage between VSS and VDD.
6 P1W passive Potentiometer 1 wiper terminal of the second resistor network, which may carry positive or negative current with voltage between VSS and VDD.
7 P0W passive Potentiometer 0 wiper terminal of the first resistor network, which may carry positive or negative current with voltage between VSS and VDD.
8 P0B passive Potentiometer 0 terminal B of the first resistor network, which may carry positive or negative current with voltage between VSS and VDD.
9 SDO output SPI serial data output, an open-drain output using the internal smart pull-up, which lets the host read wiper and TCON registers.
10 VDD power_in Positive power supply input relative to VSS; electrical performance may not meet the data sheet specifications while VDD is below 2.7V.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package MSOP-10
Category Embedded Processors & Controllers
Pins 10

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage VDD 2.7 5.5 V 4
Supply Voltage (serial interface only) VDD 1.8 2.7 V Serial Interface only. 4
Pin Voltage Range (CS, SDI, SDO, SCK, WP, SHDN) VHV 12.5 V VDD ≥ 4.5V 4
VDD Start Voltage to ensure Wiper Reset VBOR 1.65 V RAM retention voltage (VRAM) < VBOR 4
Supply Current, serial interface active (volatile write) IDD 450 µA Serial Interface Active, VDD = 5.5V, CS = VIL, SCK @ 5 MHz, write all 0’s to volatile Wiper 0 (address 0h) 4
Supply Current, EE write 1 mA EE Write Current, VDD = 5.5V, CS = VIL, SCK @ 5 MHz, write all 0’s to non-volatile Wiper 0 (address 2h) 4
Supply Current, serial interface inactive 2.5 5 µA Serial Interface Inactive, CS = VIH, VDD = 5.5V 4
Supply Current, serial interface active (decrement) 0.55 1 mA Serial Interface Active, VDD = 5.5V, CS = VIHH, SCK @ 5 MHz, decrement non-volatile Wiper 0 (address 2h) 4
Resistance (-103 device) RAB 8 10 12 kΩ -103 devices (Note 1) 5
Nominal Resistance Match (MCP42X2) /RBW0 - RBW1/ / RBW 0.25 1.5 % MCP42X2 devices only, Code = Full-Scale 5
Wiper Resistance RW 75 160 Ω VDD = 5.5 V, IW = 2.0 mA, code = 00h 5
Wiper Resistance RW 75 300 Ω VDD = 2.7 V, IW = 2.0 mA, code = 00h 5
Maximum current through A, W or B IW 2.5 mA Note 6, Worst case current through wiper when wiper is either Full-Scale or Zero Scale. 5
Schmitt Trigger High Input Threshold VIH 0.45 VDD 2.7V ≤ VDD ≤ 5.5V (Allows 2.7V Digital VDD with 5V Analog VDD) 9
Schmitt Trigger High Input Threshold VIH 0.5 VDD 1.8V ≤ VDD ≤ 2.7V 9
Schmitt Trigger Low Input Threshold VIL 0.2 VDD 9
High Voltage Input Entry Voltage VIHH 8.5 12.5 V Threshold for WiperLock Technology 9
Output Low Voltage (SDO) VOL 0.3 VDD VIOL = 5 mA, VDD = 5.5V 9
Output High Voltage (SDO) VOH 0.7 VDD VIOH = -2.5 mA, VDD = 5.5V 9
Weak Pull-up / Pull-down Current IPU 1.75 mA Internal VDD pull-up, VIHH pull-down, VDD = 5.5V, VCS = 12.5V 9
Input Leakage Current IIL -1 1 µA VIN = VDD and VIN = VSS 9
Rheostat Integral Non-linearity (10 kΩ, 8-bit) R-INL -1.5 0.5 1.5 LSb 10 kΩ 8-bit 5.5V, IW = 450 µA 7
Rheostat Integral Non-linearity (10 kΩ, 8-bit) R-INL -5.5 2.5 5.5 LSb 10 kΩ 8-bit 3.0V, IW = 240 µA (Note 7) 7
Rheostat Differential Non-linearity (10 kΩ, 8-bit) R-DNL -0.5 0.25 0.5 LSb 10 kΩ 8-bit 5.5V, IW = 450 µA 8
Rheostat Differential Non-linearity (10 kΩ, 8-bit) R-DNL -1 0.25 1 LSb 10 kΩ 8-bit 3.0V (Note 7) 8
EEPROM Programming Write Cycle Time tWC 5 10 ms 10
Power Supply Sensitivity (MCP42X2, 8-bit) PSS 0.0015 0.0035 %/% 8-bit VDD = 2.7V to 5.5V, VA = 2.7V, Code = 80h 10
SCK Input Frequency FSCK 10 MHz VDD = 2.7V to 5.5V 11
SCK Input Frequency FSCK 1 MHz VDD = 1.8V to 2.7V 11
CS Active (VIL or VIHH) to SCK↑ input TcsA2scH 60 ns 11
SCK input high time TscH 45 ns VDD = 2.7V to 5.5V 11
SCK input high time TscH 500 ns VDD = 1.8V to 2.7V 11
SCK input low time TscL 45 ns VDD = 2.7V to 5.5V 11
SCK input low time TscL 500 ns VDD = 1.8V to 2.7V 11
Setup time of SDI input to SCK↑ edge TDIV2scH 10 ns 11
Hold time of SDI input from SCK↑ edge TscH2DIL 20 ns 11
CS Inactive (VIH) to SDO output hi-impedance TcsH2DOZ 50 ns Note 1 11
SDO data output valid after SCK↓ edge TscL2DOV 70 ns VDD = 2.7V to 5.5V 11
SDO data output valid after SCK↓ edge TscL2DOV 170 ns VDD = 1.8V to 2.7V 11
CS Inactive (VIH) after SCK↑ edge TscH2csI 100 ns VDD = 2.7V to 5.5V 11
CS Inactive (VIH) after SCK↑ edge TscH2csI 1 ms VDD = 1.8V to 2.7V 11
Hold time of CS Inactive (VIH) to CS Active (VIL or VIHH) TcsA2csI 50 ns 11
Operating Temperature Range TA -40 125 °C 14
Storage Temperature Range TA -65 150 °C 14
Voltage on VDD with respect to VSS VDD -0.6 7 V 3
Voltage on CS, SCK, SDI, SDI/SDO, WP, and SHDN with respect to VSS -0.6 12.5 V 3
Input clamp current IIK -20 20 mA VI < 0, VI > VDD, VI > VPP ON HV pins 3
Output clamp current IOK -20 20 mA VO < 0 or VO > VDD 3
Maximum output current sunk by any Output pin 25 mA 3
Maximum output current sourced by any Output pin 25 mA 3
Maximum current out of VSS pin 100 mA 3
Maximum current into VDD pin 100 mA 3
Maximum current into PXA, PXW & PXB pins -2.5 2.5 mA 3
Maximum Junction Temperature (TJ) TJ 150 °C 3
ESD protection on all pins (HBM) 4 kV HBM 3
Thermal Resistance, 10L-MSOP θJA 202 °C/W 10L-MSOP 14
Ratiometric Tempco ΔVWB/ΔT 15 ppm/°C Code = Midscale (80h or 40h) 5
Nominal Resistance Tempco ΔRAB/ΔT 150 ppm/°C TA = -40°C to +125°C 5

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin P = Plastic Dual In-line (PDIP) (300 mil), 8/14-lead SN = Plastic Small Outline (SOIC), (150 mil), 8-lead 85

CAD (KiCad official)

  • Symbol: MCP4262-103E
  • Footprint: Package_SO:MSOP-10_3x3mm_P0.5mm
  • 3D model: MSOP-10 (KiCad packages3D, STEP)
  • 3D model files: mcp4262-103e-etched.step / mcp4262-103e-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mcp4262-103e.step / mcp4262-103e.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (88 pp, sha256 485870dfa4cb7357, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF