Generated by kicad-footprint-generator · KiCad file format 20260206
MCP4262-103E
Microchip Tech · Pre-ordered MCUs · MSOP-10
MCP4262-103E from Microchip Tech, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS | input | Chip select input: forcing CS to VIL enables serial commands and forcing it to VIHH enables high-voltage serial commands; the input is high-voltage tolerant with Schmitt trigger. |
| 2 | SCK | input | SPI serial clock input (high-voltage tolerant with Schmitt trigger), operating at up to 10 MHz per the SPI interface feature. |
| 3 | SDI | input | SPI serial data input, connected to the host controller SDO pin; high-voltage tolerant with Schmitt trigger. |
| 4 | VSS | power_in | Device ground reference; the electrical performance is specified relative to this pin. |
| 5 | P1B | passive | Potentiometer 1 terminal B of the second rheostat network, which may carry positive or negative current with voltage between VSS and VDD. |
| 6 | P1W | passive | Potentiometer 1 wiper terminal of the second resistor network, which may carry positive or negative current with voltage between VSS and VDD. |
| 7 | P0W | passive | Potentiometer 0 wiper terminal of the first resistor network, which may carry positive or negative current with voltage between VSS and VDD. |
| 8 | P0B | passive | Potentiometer 0 terminal B of the first resistor network, which may carry positive or negative current with voltage between VSS and VDD. |
| 9 | SDO | output | SPI serial data output, an open-drain output using the internal smart pull-up, which lets the host read wiper and TCON registers. |
| 10 | VDD | power_in | Positive power supply input relative to VSS; electrical performance may not meet the data sheet specifications while VDD is below 2.7V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | MSOP-10 |
| Category | Embedded Processors & Controllers |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VDD | 2.7 | 5.5 | V | 4 | ||
| Supply Voltage (serial interface only) | VDD | 1.8 | 2.7 | V | Serial Interface only. | 4 | |
| Pin Voltage Range (CS, SDI, SDO, SCK, WP, SHDN) | VHV | 12.5 | V | VDD ≥ 4.5V | 4 | ||
| VDD Start Voltage to ensure Wiper Reset | VBOR | 1.65 | V | RAM retention voltage (VRAM) < VBOR | 4 | ||
| Supply Current, serial interface active (volatile write) | IDD | 450 | µA | Serial Interface Active, VDD = 5.5V, CS = VIL, SCK @ 5 MHz, write all 0’s to volatile Wiper 0 (address 0h) | 4 | ||
| Supply Current, EE write | 1 | mA | EE Write Current, VDD = 5.5V, CS = VIL, SCK @ 5 MHz, write all 0’s to non-volatile Wiper 0 (address 2h) | 4 | |||
| Supply Current, serial interface inactive | 2.5 | 5 | µA | Serial Interface Inactive, CS = VIH, VDD = 5.5V | 4 | ||
| Supply Current, serial interface active (decrement) | 0.55 | 1 | mA | Serial Interface Active, VDD = 5.5V, CS = VIHH, SCK @ 5 MHz, decrement non-volatile Wiper 0 (address 2h) | 4 | ||
| Resistance (-103 device) | RAB | 8 | 10 | 12 | kΩ | -103 devices (Note 1) | 5 |
| Nominal Resistance Match (MCP42X2) | /RBW0 - RBW1/ / RBW | 0.25 | 1.5 | % | MCP42X2 devices only, Code = Full-Scale | 5 | |
| Wiper Resistance | RW | 75 | 160 | Ω | VDD = 5.5 V, IW = 2.0 mA, code = 00h | 5 | |
| Wiper Resistance | RW | 75 | 300 | Ω | VDD = 2.7 V, IW = 2.0 mA, code = 00h | 5 | |
| Maximum current through A, W or B | IW | 2.5 | mA | Note 6, Worst case current through wiper when wiper is either Full-Scale or Zero Scale. | 5 | ||
| Schmitt Trigger High Input Threshold | VIH | 0.45 | VDD | 2.7V ≤ VDD ≤ 5.5V (Allows 2.7V Digital VDD with 5V Analog VDD) | 9 | ||
| Schmitt Trigger High Input Threshold | VIH | 0.5 | VDD | 1.8V ≤ VDD ≤ 2.7V | 9 | ||
| Schmitt Trigger Low Input Threshold | VIL | 0.2 | VDD | 9 | |||
| High Voltage Input Entry Voltage | VIHH | 8.5 | 12.5 | V | Threshold for WiperLock Technology | 9 | |
| Output Low Voltage (SDO) | VOL | 0.3 | VDD | VIOL = 5 mA, VDD = 5.5V | 9 | ||
| Output High Voltage (SDO) | VOH | 0.7 | VDD | VIOH = -2.5 mA, VDD = 5.5V | 9 | ||
| Weak Pull-up / Pull-down Current | IPU | 1.75 | mA | Internal VDD pull-up, VIHH pull-down, VDD = 5.5V, VCS = 12.5V | 9 | ||
| Input Leakage Current | IIL | -1 | 1 | µA | VIN = VDD and VIN = VSS | 9 | |
| Rheostat Integral Non-linearity (10 kΩ, 8-bit) | R-INL | -1.5 | 0.5 | 1.5 | LSb | 10 kΩ 8-bit 5.5V, IW = 450 µA | 7 |
| Rheostat Integral Non-linearity (10 kΩ, 8-bit) | R-INL | -5.5 | 2.5 | 5.5 | LSb | 10 kΩ 8-bit 3.0V, IW = 240 µA (Note 7) | 7 |
| Rheostat Differential Non-linearity (10 kΩ, 8-bit) | R-DNL | -0.5 | 0.25 | 0.5 | LSb | 10 kΩ 8-bit 5.5V, IW = 450 µA | 8 |
| Rheostat Differential Non-linearity (10 kΩ, 8-bit) | R-DNL | -1 | 0.25 | 1 | LSb | 10 kΩ 8-bit 3.0V (Note 7) | 8 |
| EEPROM Programming Write Cycle Time | tWC | 5 | 10 | ms | 10 | ||
| Power Supply Sensitivity (MCP42X2, 8-bit) | PSS | 0.0015 | 0.0035 | %/% | 8-bit VDD = 2.7V to 5.5V, VA = 2.7V, Code = 80h | 10 | |
| SCK Input Frequency | FSCK | 10 | MHz | VDD = 2.7V to 5.5V | 11 | ||
| SCK Input Frequency | FSCK | 1 | MHz | VDD = 1.8V to 2.7V | 11 | ||
| CS Active (VIL or VIHH) to SCK↑ input | TcsA2scH | 60 | ns | 11 | |||
| SCK input high time | TscH | 45 | ns | VDD = 2.7V to 5.5V | 11 | ||
| SCK input high time | TscH | 500 | ns | VDD = 1.8V to 2.7V | 11 | ||
| SCK input low time | TscL | 45 | ns | VDD = 2.7V to 5.5V | 11 | ||
| SCK input low time | TscL | 500 | ns | VDD = 1.8V to 2.7V | 11 | ||
| Setup time of SDI input to SCK↑ edge | TDIV2scH | 10 | ns | 11 | |||
| Hold time of SDI input from SCK↑ edge | TscH2DIL | 20 | ns | 11 | |||
| CS Inactive (VIH) to SDO output hi-impedance | TcsH2DOZ | 50 | ns | Note 1 | 11 | ||
| SDO data output valid after SCK↓ edge | TscL2DOV | 70 | ns | VDD = 2.7V to 5.5V | 11 | ||
| SDO data output valid after SCK↓ edge | TscL2DOV | 170 | ns | VDD = 1.8V to 2.7V | 11 | ||
| CS Inactive (VIH) after SCK↑ edge | TscH2csI | 100 | ns | VDD = 2.7V to 5.5V | 11 | ||
| CS Inactive (VIH) after SCK↑ edge | TscH2csI | 1 | ms | VDD = 1.8V to 2.7V | 11 | ||
| Hold time of CS Inactive (VIH) to CS Active (VIL or VIHH) | TcsA2csI | 50 | ns | 11 | |||
| Operating Temperature Range | TA | -40 | 125 | °C | 14 | ||
| Storage Temperature Range | TA | -65 | 150 | °C | 14 | ||
| Voltage on VDD with respect to VSS | VDD | -0.6 | 7 | V | 3 | ||
| Voltage on CS, SCK, SDI, SDI/SDO, WP, and SHDN with respect to VSS | -0.6 | 12.5 | V | 3 | |||
| Input clamp current | IIK | -20 | 20 | mA | VI < 0, VI > VDD, VI > VPP ON HV pins | 3 | |
| Output clamp current | IOK | -20 | 20 | mA | VO < 0 or VO > VDD | 3 | |
| Maximum output current sunk by any Output pin | 25 | mA | 3 | ||||
| Maximum output current sourced by any Output pin | 25 | mA | 3 | ||||
| Maximum current out of VSS pin | 100 | mA | 3 | ||||
| Maximum current into VDD pin | 100 | mA | 3 | ||||
| Maximum current into PXA, PXW & PXB pins | -2.5 | 2.5 | mA | 3 | |||
| Maximum Junction Temperature (TJ) | TJ | 150 | °C | 3 | |||
| ESD protection on all pins (HBM) | 4 | kV | HBM | 3 | |||
| Thermal Resistance, 10L-MSOP | θJA | 202 | °C/W | 10L-MSOP | 14 | ||
| Ratiometric Tempco | ΔVWB/ΔT | 15 | ppm/°C | Code = Midscale (80h or 40h) | 5 | ||
| Nominal Resistance Tempco | ΔRAB/ΔT | 150 | ppm/°C | TA = -40°C to +125°C | 5 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | P = Plastic Dual In-line (PDIP) (300 mil), 8/14-lead SN = Plastic Small Outline (SOIC), (150 mil), 8-lead | 85 |
CAD (KiCad official)
- Symbol:
MCP4262-103E - Footprint:
Package_SO:MSOP-10_3x3mm_P0.5mm - 3D model: MSOP-10 (KiCad packages3D, STEP)
- 3D model files:
mcp4262-103e-etched.step/mcp4262-103e-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp4262-103e.step/mcp4262-103e.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (88 pp, sha256
485870dfa4cb7357, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).