Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

NCN6001DTBR2G

onsemi · Interface - Specialized · TSSOP-20

NCN6001DTBR2G from onsemi, in a TSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 I/O bidirectional Connects to the external microcontroller serial I/O line through a bidirectional level translator, with an internal pullup that is active only when the chip is selected.
2 INT output Goes LOW to signal card insertion detected by CRD_DET, CRD_VCC overload, or card extraction, and is forced HIGH when VCC drops below 2.0 V.
3 CLK_IN input Schmitt-trigger clock input that is translated to CRD_CLK at the same frequency or divided by 2 or 4, and the chip guarantees 50% EMV duty cycle for the 1/2 and 1/4 ratios.
4 MOSI input SPI data input from the external microcontroller that carries the address of one of four possible chips and the programming code for the interface.
5 CLK_SPI input SPI clock input with a Schmitt-trigger receiver that synchronizes the data transfer and is fully independent of CLK_IN.
6 EN_RPU input Logic input that connects the I/O pullup resistor when High and disconnects it when Low, and must be tied to the correct voltage level because no pullup is built in.
7 MISO output SPI data output that carries the interface state during the same MOSI frame, where bits b7:b5 must be discarded and an external 4.7 k pulldown may be needed in the High Z state.
8 CS input Chip select input that synchronizes SPI communication and disables all NCN6001 functions when driven High.
9 VCC power_in Supply input for the device, which must be bypassed to ground with a 10 µF/6.0 V capacitor, with low-ESR ceramic recommended over tantalum.
10 Lout_L passive Low side of the DC/DC external inductor, typically 22 µH with DCR < 2.0 Ω, for a maximum 65 mA DC output load, and the inductor must handle a 450 mA peak current.
11 PWR_GND power_in Power ground for the built-in DC/DC converter, which must be connected to the system ground together with GND pin 16.
12 Lout_H passive High side of the DC/DC external inductor, connected to pin 10 to activate the DC/DC function together with the built-in NMOS and PMOS switches.
13 CRD_VCC power_out Card supply output that is programmable to 1.8 V, 3.0 V or 5.0 V and must be smoothed by a 10 µF low-ESR capacitor to GND, with the DC/DC converter shut off on overload.
14 C8/S1 bidirectional Auxiliary mixed analog/digital line driven by an open-drain stage with pullup to CRD_VCC, used for synchronous card I/O or as a chip-select identification bit (MISO bit 0).
15 C4/S0 bidirectional Auxiliary mixed analog/digital line driven by an open-drain stage with pullup to CRD_VCC, used for synchronous card I/O or as a chip-select identification bit (MISO bit 1).
16 GND power_in Logic and low-level analog ground that must be externally connected to PWR_GND pin 11 while keeping high current transients separate from low signal currents.
17 CRD_CLK output Clock output to the card CLK contact with programmable FAST or SLOW rise and fall slopes, held low by an internal pulldown during CRD_VCC startup or when CRD_VCC = 0 V.
18 CRD_DET input Card presence input with an internal pullup of about 5.0 µA that is active LOW with a programmable polarity and a built-in digital filter against voltage spikes.
19 CRD_RST output Card RESET output from the level translator, with output current internally limited to 15 mA and held low by an internal pulldown when the card is deactivated.
20 CRD_IO bidirectional Card serial data line with a bidirectional level translator, internal pulldown during CRD_VCC startup or when CRD_VCC = 0 V, and current internally limited to 15 mA.

Key specifications

Parameter Value
Manufacturer onsemi
Package TSSOP-20
Category Interface ICs
Pins 20

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
housing Abs 1. Human Body Model, R = 1500 , C = 100 pF. 2. Absolute Maximum Rating beyond which damage to the device may occur. 6

CAD (KiCad official)

  • Symbol: NCN6001DTBR2G
  • Footprint: Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm
  • 3D model: TSSOP-20 (KiCad packages3D, STEP)
  • 3D model files: ncn6001dtbr2g-etched.step / ncn6001dtbr2g-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ncn6001dtbr2g.step / ncn6001dtbr2g.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (33 pp, sha256 879061db33ea5753, retrieved 2026-11-21)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF