3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownNCN6001DTBR2G
onsemi · Interface - Specialized · TSSOP-20
NCN6001DTBR2G from onsemi, in a TSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | I/O | bidirectional | Connects to the external microcontroller serial I/O line through a bidirectional level translator, with an internal pullup that is active only when the chip is selected. |
| 2 | INT | output | Goes LOW to signal card insertion detected by CRD_DET, CRD_VCC overload, or card extraction, and is forced HIGH when VCC drops below 2.0 V. |
| 3 | CLK_IN | input | Schmitt-trigger clock input that is translated to CRD_CLK at the same frequency or divided by 2 or 4, and the chip guarantees 50% EMV duty cycle for the 1/2 and 1/4 ratios. |
| 4 | MOSI | input | SPI data input from the external microcontroller that carries the address of one of four possible chips and the programming code for the interface. |
| 5 | CLK_SPI | input | SPI clock input with a Schmitt-trigger receiver that synchronizes the data transfer and is fully independent of CLK_IN. |
| 6 | EN_RPU | input | Logic input that connects the I/O pullup resistor when High and disconnects it when Low, and must be tied to the correct voltage level because no pullup is built in. |
| 7 | MISO | output | SPI data output that carries the interface state during the same MOSI frame, where bits b7:b5 must be discarded and an external 4.7 k pulldown may be needed in the High Z state. |
| 8 | CS | input | Chip select input that synchronizes SPI communication and disables all NCN6001 functions when driven High. |
| 9 | VCC | power_in | Supply input for the device, which must be bypassed to ground with a 10 µF/6.0 V capacitor, with low-ESR ceramic recommended over tantalum. |
| 10 | Lout_L | passive | Low side of the DC/DC external inductor, typically 22 µH with DCR < 2.0 Ω, for a maximum 65 mA DC output load, and the inductor must handle a 450 mA peak current. |
| 11 | PWR_GND | power_in | Power ground for the built-in DC/DC converter, which must be connected to the system ground together with GND pin 16. |
| 12 | Lout_H | passive | High side of the DC/DC external inductor, connected to pin 10 to activate the DC/DC function together with the built-in NMOS and PMOS switches. |
| 13 | CRD_VCC | power_out | Card supply output that is programmable to 1.8 V, 3.0 V or 5.0 V and must be smoothed by a 10 µF low-ESR capacitor to GND, with the DC/DC converter shut off on overload. |
| 14 | C8/S1 | bidirectional | Auxiliary mixed analog/digital line driven by an open-drain stage with pullup to CRD_VCC, used for synchronous card I/O or as a chip-select identification bit (MISO bit 0). |
| 15 | C4/S0 | bidirectional | Auxiliary mixed analog/digital line driven by an open-drain stage with pullup to CRD_VCC, used for synchronous card I/O or as a chip-select identification bit (MISO bit 1). |
| 16 | GND | power_in | Logic and low-level analog ground that must be externally connected to PWR_GND pin 11 while keeping high current transients separate from low signal currents. |
| 17 | CRD_CLK | output | Clock output to the card CLK contact with programmable FAST or SLOW rise and fall slopes, held low by an internal pulldown during CRD_VCC startup or when CRD_VCC = 0 V. |
| 18 | CRD_DET | input | Card presence input with an internal pullup of about 5.0 µA that is active LOW with a programmable polarity and a built-in digital filter against voltage spikes. |
| 19 | CRD_RST | output | Card RESET output from the level translator, with output current internally limited to 15 mA and held low by an internal pulldown when the card is deactivated. |
| 20 | CRD_IO | bidirectional | Card serial data line with a bidirectional level translator, internal pulldown during CRD_VCC startup or when CRD_VCC = 0 V, and current internally limited to 15 mA. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | TSSOP-20 |
| Category | Interface ICs |
| Pins | 20 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | Abs | 1. Human Body Model, R = 1500 , C = 100 pF. 2. Absolute Maximum Rating beyond which damage to the device may occur. | 6 |
CAD (KiCad official)
- Symbol:
NCN6001DTBR2G - Footprint:
Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm - 3D model: TSSOP-20 (KiCad packages3D, STEP)
- 3D model files:
ncn6001dtbr2g-etched.step/ncn6001dtbr2g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncn6001dtbr2g.step/ncn6001dtbr2g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (33 pp, sha256
879061db33ea5753, retrieved 2026-11-21) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).