Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

SEC1110-A5-02

Microchip Tech · Pre-ordered MCUs · QFN-16-EP(5x5)

SEC1110-A5-02 from Microchip Tech, in a QFN-16-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VDD5 power_in 5.0 V (or VBUS) power input; the datasheet gives a 3.6 V to 5.5 V supply input range and an internal 4.8 V comparator disables Class A card support when the input is too low.
2 SC1_C8 bidirectional Smart Card 1 C8 contact, usable for standard or proprietary use as an input and/or output, and may alternatively be used as GPIO4.
3 SC1_C4 bidirectional Smart Card 1 C4 contact, attached to C4 of the Smart Card for cards that support Function Code, and may alternatively be used as GPIO3.
4 SC1_IO bidirectional Smart Card 1 bidirectional serial data pin, which should be held low when the interface is not active, and may alternatively be used as GPIO0.
5 SC1_CLK output Smart Card 1 clock reference output for communication with the card, which should be held low when the interface is not active, and may alternatively be used as GPIO1.
6 SC1_RST_N output Smart Card 1 active-low reset output; a low pulse resets the card and triggers an answer-to-reset response, and the pin should be held low when the interface is not active.
7 SC1_VCC power_out Smart Card 1 supply output that can be set to 1.8, 3.0, or 5.0 volts depending on the detected card and requires an external 1 µF capacitor.
8 SC1_PRSNT_N/JTAG_TMS bidirectional Active-low Smart Card 1 presence detect input with a software-enableable internal pull-up, which can alternatively be configured as JTAG_TMS in debug mode or as GPIO6 or Timer 0 input.
9 TEST bidirectional Test mode pin used for testing the chip, which must be tied low externally if the test function is not used.
10 USB_DM bidirectional USB D- data line connecting to the upstream USB bus, an analog input/output defined in the USB specification.
11 USB_DP bidirectional USB D+ data line connecting to the upstream USB bus, an analog input/output defined in the USB specification.
12 VDD33 power_out 3.3 V analog power output for decoupling, which requires an external 1 µF capacitor.
13 JTAG_CLK bidirectional JTAG debug clock input with a weak pull-down, which can be left floating or grounded when not used.
14 SC_LED_ACT_N/JTAG_TDO bidirectional Driver for the Smart Card active LED, which can alternatively be configured as JTAG_TDO in debug mode or as Timer 2 T2EX input or GPIO5.
15 JTAG_TDI bidirectional JTAG data input with a weak pull-down, which can alternatively be used in debug mode as configured by software.
16 RESET_N input Active-low system reset input with Schmitt trigger, which resets the chip and enters STOP mode, requiring a pulse of at least 1 µs and having an analog input threshold of Vil=100 mV.
17 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package QFN-16-EP(5x5)
Category Single Chip Microcomputer/Microcontroller
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Storage Temperature TSTOR -55 150 °C 188
VDD5 supply voltage VDD5 -0.3 5.5 V 188
Voltage on USB_DP and USB_DM pins -0.3 3.6 V 3.3 V 10% 188
Voltage on RESET_N 0 V Max = VDD5 (Note 18-3) 188
Voltage on any signal pin -0.3 5.5 V Positive voltage w.r.t. ground 5.5V; negative -0.3V 188
Operating Temperature TA 0 70 °C Commercial (no I suffix); ambient temperature in air (Notes 18-1, 18-2) 189
5.0V supply voltage VDD5 3.6 5.5 V Class A smart card support needs 4.8 V minimum, which may not be met by VBUS 189
VDD5 supply rise time tRT 400 ns Figure 18-1 189
Voltage on USB_DP and USB_DM pins 3 3.6 V If VDD5 drops below 3.6V, MAX becomes VDD5 189
Voltage on RESET_N 0 V Max = VDD5 (Note 18-3) 189
Voltage on any signal pin -0.3 5.5 V Other than USB_DP, USB_DM, Smart Card pins, RESET_N 189
Low Output Level VOL 0.4 V IOL = -8 mA 189
8 mA I/O sinking current IOL8 8.3 12.6 18.4 mA VOUT = 0.4V 189
8 mA I/O sinking output impedance ROL8 21.7 31.6 48.3 Ω VOUT = 0.4V 189
8 mA I/O sourcing current IOH8 8.1 11.6 16 mA VOUT = VDD33 - 0.4V 189
8 mA I/O sourcing output impedance ROH8 25 34.6 50 Ω VOUT = VDD33 - 0.4V 189
Output Leakage IIH5 1 µA VIN = 0 to VDD33, 27°C 189
Output Leakage IIH5 1.4 8 12 µA VIN = 0 to 5.5V, 27°C 189
Output Leakage IIH5 20 µA VIN = 0 to 5.5V, 85°C 189
Output Leakage IIH5 80 µA VIN = 0 to 5.5V, 125°C (Note 18-3) 189
Low Input Level VIL -0.3 0.8 V 189
High Input Level VIH5 2 5.5 V 189
Hysteresis VHYSI 336 399 459 mV 189
Pull-Down resistance RDPD 46 65 90 kΩ Vpad = VDD33 189
Pull-Down current IDPD 33 50 79 µA Vpad = VDD33 189
Pull-Up resistance RDPU 53 66 80 kΩ Vpad = 0V (Note 18-8) 189
Pull-Up current IDPU 38 50 68 µA Vpad = 0V 189
RESET_N Rise Time Trst_r 100 ns RESET_N pad (Note 18-3) 190
RESET_N Fall Time Trst_f 100 ns RESET_N pad (Note 18-3) 190
RESET_N Low Input level VILRST 0.1 V RESET_N low causes STOP mode entry 190
Oscillator 48 MHz accuracy (USB Dynamic Trim enabled) F48acc 0.1 0.2 % -40 < T < 125 °C, 3.6 < VDD5 < 6.8V; internal oscillator @48 MHz with USB Dynamic Trim enabled 190
Oscillator 48 MHz accuracy (USB Dynamic Trim disabled) F48accd 0.82 1.5 % -40 < T < 125 °C, 3.6 < VDD5 < 6.8V; internal oscillator @48 MHz without USB Dynamic Trim enabled 190
Oscillator 8 MHz accuracy F8acc 0.78 1.83 % Internal oscillator @ 8 MHz 190
Oscillator 4 MHz accuracy F4acc 0.78 1.83 % Internal oscillator @ 4 MHz 190
Smart Card Power Supply Voltage (Class A) VSC1_VCC, VSC2_VCC 4.6 V Class A mode, ISC1_VCC = 0 to 55 mA (Note 18-13) 190
Smart Card Power Supply Voltage (Class B) VSC1_VCC, VSC2_VCC 2.76 3 3.24 V Class B mode 190
Smart Card Power Supply Voltage (Class C) VSC1_VCC, VSC2_VCC 1.66 1.8 1.94 V Class C mode 190
Smart Card Power Supply current ISC1, ISC2 55 mA Class A/B/C 190
Smart Card Over Current Sense (OCS) Detection IOCS1, IOCS2 110 mA 190
Detection Time on OCS tOSCDET 1 µs 190
SC1_VCC/SC2_VCC Turn Off Time tSCOFF 5 ms SEC1110/SEC1210 A1 version (Note 18-14) 190
SC1_VCC/SC2_VCC Turn Off Time tSCOFF 500 µs All later versions (Note 18-14) 190
SC1_VCC/SC2_VCC Turn On Time tSCON 1 ms 1.0 µF load (Note 18-14) 190
SC1_CLK/SC2_CLK Low Output Level (Class A) VOL 0 0.4 V @CL=30pF, VSCx_VCC=min; A1 version: 100µA < IOL < 0; later versions: IOLmax = -1 mA @125°C 191
SC1_CLK/SC2_CLK Low Output Level (Class B) VOL 0 0.4 V @CL=30pF, VSCx_VCC=min; A1 version: 100µA < IOL < 0; later versions: IOLmax = -1 mA @125°C 191
SC1_CLK/SC2_CLK Low Output Level (Class C) VOL 0 0.15 V @CL=30pF, VSCx_VCC=min; A1 version: 100µA < IOL < 0; later versions: IOLmax = -1 mA @125°C 191
SC1_CLK, SC2_CLK Rise Time tR 9.9 13 16.67 ns @ CL = 30 pF, Rload = 33Ω, Class A/B/C 191
SC1_CLK, SC2_CLK Fall Time tF 6.5 10 16.2 ns @ CL = 30 pF, Rload = 33Ω, Class A/B/C 191
SC1_CLK, SC2_CLK Clock Accuracy (USB Dynamic Trimming on) 0.1 0.25 % USB Dynamic Trimming is on 191
SC1_CLK, SC2_CLK Clock Accuracy (USB dynamic trim off) 0.82 1.5 % USB dynamic trim is off (same as F48accd) 191
SC1_CLK, SC2_CLK Clock Duty Cycle 48 52 % Oscillator in 48 MHz mode 191
SC1_CLK, SC2_CLK Frequency FSCx_CLK 1 4.8 MHz Generated by dividing 48 MHz by an integer ranging from 10 to 48 191

CAD (KiCad official)

  • Symbol: SEC1110-A5-02
  • Footprint: Package_DFN_QFN:QFN-16-1EP_5x5mm_P0.8mm_EP2.7x2.7mm
  • 3D model: QFN-16-EP(5x5) (KiCad packages3D, STEP)
  • 3D model files: sec1110-a5-02-etched.step / sec1110-a5-02-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); sec1110-a5-02.step / sec1110-a5-02.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (220 pp, sha256 3d50372dd19b6208, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF