Generated by kicad-footprint-generator · KiCad file format 20260206
SEC1110-A5-02
Microchip Tech · Pre-ordered MCUs · QFN-16-EP(5x5)
SEC1110-A5-02 from Microchip Tech, in a QFN-16-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD5 | power_in | 5.0 V (or VBUS) power input; the datasheet gives a 3.6 V to 5.5 V supply input range and an internal 4.8 V comparator disables Class A card support when the input is too low. |
| 2 | SC1_C8 | bidirectional | Smart Card 1 C8 contact, usable for standard or proprietary use as an input and/or output, and may alternatively be used as GPIO4. |
| 3 | SC1_C4 | bidirectional | Smart Card 1 C4 contact, attached to C4 of the Smart Card for cards that support Function Code, and may alternatively be used as GPIO3. |
| 4 | SC1_IO | bidirectional | Smart Card 1 bidirectional serial data pin, which should be held low when the interface is not active, and may alternatively be used as GPIO0. |
| 5 | SC1_CLK | output | Smart Card 1 clock reference output for communication with the card, which should be held low when the interface is not active, and may alternatively be used as GPIO1. |
| 6 | SC1_RST_N | output | Smart Card 1 active-low reset output; a low pulse resets the card and triggers an answer-to-reset response, and the pin should be held low when the interface is not active. |
| 7 | SC1_VCC | power_out | Smart Card 1 supply output that can be set to 1.8, 3.0, or 5.0 volts depending on the detected card and requires an external 1 µF capacitor. |
| 8 | SC1_PRSNT_N/JTAG_TMS | bidirectional | Active-low Smart Card 1 presence detect input with a software-enableable internal pull-up, which can alternatively be configured as JTAG_TMS in debug mode or as GPIO6 or Timer 0 input. |
| 9 | TEST | bidirectional | Test mode pin used for testing the chip, which must be tied low externally if the test function is not used. |
| 10 | USB_DM | bidirectional | USB D- data line connecting to the upstream USB bus, an analog input/output defined in the USB specification. |
| 11 | USB_DP | bidirectional | USB D+ data line connecting to the upstream USB bus, an analog input/output defined in the USB specification. |
| 12 | VDD33 | power_out | 3.3 V analog power output for decoupling, which requires an external 1 µF capacitor. |
| 13 | JTAG_CLK | bidirectional | JTAG debug clock input with a weak pull-down, which can be left floating or grounded when not used. |
| 14 | SC_LED_ACT_N/JTAG_TDO | bidirectional | Driver for the Smart Card active LED, which can alternatively be configured as JTAG_TDO in debug mode or as Timer 2 T2EX input or GPIO5. |
| 15 | JTAG_TDI | bidirectional | JTAG data input with a weak pull-down, which can alternatively be used in debug mode as configured by software. |
| 16 | RESET_N | input | Active-low system reset input with Schmitt trigger, which resets the chip and enters STOP mode, requiring a pulse of at least 1 µs and having an analog input threshold of Vil=100 mV. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | QFN-16-EP(5x5) |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage Temperature | TSTOR | -55 | 150 | °C | 188 | ||
| VDD5 supply voltage | VDD5 | -0.3 | 5.5 | V | 188 | ||
| Voltage on USB_DP and USB_DM pins | -0.3 | 3.6 | V | 3.3 V 10% | 188 | ||
| Voltage on RESET_N | 0 | V | Max = VDD5 (Note 18-3) | 188 | |||
| Voltage on any signal pin | -0.3 | 5.5 | V | Positive voltage w.r.t. ground 5.5V; negative -0.3V | 188 | ||
| Operating Temperature | TA | 0 | 70 | °C | Commercial (no I suffix); ambient temperature in air (Notes 18-1, 18-2) | 189 | |
| 5.0V supply voltage | VDD5 | 3.6 | 5.5 | V | Class A smart card support needs 4.8 V minimum, which may not be met by VBUS | 189 | |
| VDD5 supply rise time | tRT | 400 | ns | Figure 18-1 | 189 | ||
| Voltage on USB_DP and USB_DM pins | 3 | 3.6 | V | If VDD5 drops below 3.6V, MAX becomes VDD5 | 189 | ||
| Voltage on RESET_N | 0 | V | Max = VDD5 (Note 18-3) | 189 | |||
| Voltage on any signal pin | -0.3 | 5.5 | V | Other than USB_DP, USB_DM, Smart Card pins, RESET_N | 189 | ||
| Low Output Level | VOL | 0.4 | V | IOL = -8 mA | 189 | ||
| 8 mA I/O sinking current | IOL8 | 8.3 | 12.6 | 18.4 | mA | VOUT = 0.4V | 189 |
| 8 mA I/O sinking output impedance | ROL8 | 21.7 | 31.6 | 48.3 | Ω | VOUT = 0.4V | 189 |
| 8 mA I/O sourcing current | IOH8 | 8.1 | 11.6 | 16 | mA | VOUT = VDD33 - 0.4V | 189 |
| 8 mA I/O sourcing output impedance | ROH8 | 25 | 34.6 | 50 | Ω | VOUT = VDD33 - 0.4V | 189 |
| Output Leakage | IIH5 | 1 | µA | VIN = 0 to VDD33, 27°C | 189 | ||
| Output Leakage | IIH5 | 1.4 | 8 | 12 | µA | VIN = 0 to 5.5V, 27°C | 189 |
| Output Leakage | IIH5 | 20 | µA | VIN = 0 to 5.5V, 85°C | 189 | ||
| Output Leakage | IIH5 | 80 | µA | VIN = 0 to 5.5V, 125°C (Note 18-3) | 189 | ||
| Low Input Level | VIL | -0.3 | 0.8 | V | 189 | ||
| High Input Level | VIH5 | 2 | 5.5 | V | 189 | ||
| Hysteresis | VHYSI | 336 | 399 | 459 | mV | 189 | |
| Pull-Down resistance | RDPD | 46 | 65 | 90 | kΩ | Vpad = VDD33 | 189 |
| Pull-Down current | IDPD | 33 | 50 | 79 | µA | Vpad = VDD33 | 189 |
| Pull-Up resistance | RDPU | 53 | 66 | 80 | kΩ | Vpad = 0V (Note 18-8) | 189 |
| Pull-Up current | IDPU | 38 | 50 | 68 | µA | Vpad = 0V | 189 |
| RESET_N Rise Time | Trst_r | 100 | ns | RESET_N pad (Note 18-3) | 190 | ||
| RESET_N Fall Time | Trst_f | 100 | ns | RESET_N pad (Note 18-3) | 190 | ||
| RESET_N Low Input level | VILRST | 0.1 | V | RESET_N low causes STOP mode entry | 190 | ||
| Oscillator 48 MHz accuracy (USB Dynamic Trim enabled) | F48acc | 0.1 | 0.2 | % | -40 < T < 125 °C, 3.6 < VDD5 < 6.8V; internal oscillator @48 MHz with USB Dynamic Trim enabled | 190 | |
| Oscillator 48 MHz accuracy (USB Dynamic Trim disabled) | F48accd | 0.82 | 1.5 | % | -40 < T < 125 °C, 3.6 < VDD5 < 6.8V; internal oscillator @48 MHz without USB Dynamic Trim enabled | 190 | |
| Oscillator 8 MHz accuracy | F8acc | 0.78 | 1.83 | % | Internal oscillator @ 8 MHz | 190 | |
| Oscillator 4 MHz accuracy | F4acc | 0.78 | 1.83 | % | Internal oscillator @ 4 MHz | 190 | |
| Smart Card Power Supply Voltage (Class A) | VSC1_VCC, VSC2_VCC | 4.6 | V | Class A mode, ISC1_VCC = 0 to 55 mA (Note 18-13) | 190 | ||
| Smart Card Power Supply Voltage (Class B) | VSC1_VCC, VSC2_VCC | 2.76 | 3 | 3.24 | V | Class B mode | 190 |
| Smart Card Power Supply Voltage (Class C) | VSC1_VCC, VSC2_VCC | 1.66 | 1.8 | 1.94 | V | Class C mode | 190 |
| Smart Card Power Supply current | ISC1, ISC2 | 55 | mA | Class A/B/C | 190 | ||
| Smart Card Over Current Sense (OCS) Detection | IOCS1, IOCS2 | 110 | mA | 190 | |||
| Detection Time on OCS | tOSCDET | 1 | µs | 190 | |||
| SC1_VCC/SC2_VCC Turn Off Time | tSCOFF | 5 | ms | SEC1110/SEC1210 A1 version (Note 18-14) | 190 | ||
| SC1_VCC/SC2_VCC Turn Off Time | tSCOFF | 500 | µs | All later versions (Note 18-14) | 190 | ||
| SC1_VCC/SC2_VCC Turn On Time | tSCON | 1 | ms | 1.0 µF load (Note 18-14) | 190 | ||
| SC1_CLK/SC2_CLK Low Output Level (Class A) | VOL | 0 | 0.4 | V | @CL=30pF, VSCx_VCC=min; A1 version: 100µA < IOL < 0; later versions: IOLmax = -1 mA @125°C | 191 | |
| SC1_CLK/SC2_CLK Low Output Level (Class B) | VOL | 0 | 0.4 | V | @CL=30pF, VSCx_VCC=min; A1 version: 100µA < IOL < 0; later versions: IOLmax = -1 mA @125°C | 191 | |
| SC1_CLK/SC2_CLK Low Output Level (Class C) | VOL | 0 | 0.15 | V | @CL=30pF, VSCx_VCC=min; A1 version: 100µA < IOL < 0; later versions: IOLmax = -1 mA @125°C | 191 | |
| SC1_CLK, SC2_CLK Rise Time | tR | 9.9 | 13 | 16.67 | ns | @ CL = 30 pF, Rload = 33Ω, Class A/B/C | 191 |
| SC1_CLK, SC2_CLK Fall Time | tF | 6.5 | 10 | 16.2 | ns | @ CL = 30 pF, Rload = 33Ω, Class A/B/C | 191 |
| SC1_CLK, SC2_CLK Clock Accuracy (USB Dynamic Trimming on) | 0.1 | 0.25 | % | USB Dynamic Trimming is on | 191 | ||
| SC1_CLK, SC2_CLK Clock Accuracy (USB dynamic trim off) | 0.82 | 1.5 | % | USB dynamic trim is off (same as F48accd) | 191 | ||
| SC1_CLK, SC2_CLK Clock Duty Cycle | 48 | 52 | % | Oscillator in 48 MHz mode | 191 | ||
| SC1_CLK, SC2_CLK Frequency | FSCx_CLK | 1 | 4.8 | MHz | Generated by dividing 48 MHz by an integer ranging from 10 to 48 | 191 |
CAD (KiCad official)
- Symbol:
SEC1110-A5-02 - Footprint:
Package_DFN_QFN:QFN-16-1EP_5x5mm_P0.8mm_EP2.7x2.7mm - 3D model: QFN-16-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
sec1110-a5-02-etched.step/sec1110-a5-02-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sec1110-a5-02.step/sec1110-a5-02.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (220 pp, sha256
3d50372dd19b6208, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).