3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownA3966SLBTR-T
Allegro MicroSystems, LLC · Gate Drive ICs · SOIC-16
A3966SLBTR-T from Allegro MicroSystems, LLC, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT1A | output | Bridge 1 output A. |
| 2 | PHASE 1 | input | Bridge 1 phase (current direction) input. |
| 3 | ENABLE 1 | input | Bridge 1 enable input. |
| 4 | GROUND | power_in | Ground; fused internally to the die pad with pin 13 for heat dissipation ('Pins 4 and 13 fused internally'). |
| 5 | SENSE1 | passive | Bridge 1 current-sense resistor connection. |
| 6 | OUT 1B | output | Bridge 1 output B. |
| 7 | LOAD SUPPLY | power_in | Load supply VBB (max 30 V). |
| 8 | REFERENCE | input | Current-limit reference voltage VREF. |
| 9 | RC | passive | Fixed off-time RC timing network. |
| 10 | LOGIC SUPPLY | power_in | Logic supply VCC (max 7.0 V). |
| 11 | OUT 2B | output | Bridge 2 output B. |
| 12 | SENSE 2 | passive | Bridge 2 current-sense resistor connection. |
| 13 | GROUND | power_in | Ground; fused internally to the die pad with pin 4. |
| 14 | ENABLE 2 | input | Bridge 2 enable input. |
| 15 | PHASE 2 | input | Bridge 2 phase (current direction) input. |
| 16 | OUT 2A | output | Bridge 2 output A. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Allegro MicroSystems, LLC |
| Package | SOIC-16 |
| Category | Power Management |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Load Supply Voltage Range | VBB | 30 | V | Operating, IOUT = ±650 mA, L = 3 mH; min cell prints 'VCC' (symbol, no number) | 4 | ||
| Output Leakage Current | ICEX | 50 | µA | VOUT = 30 V; typ cell prints '<1.0' | 4 | ||
| Output Leakage Current | ICEX | -50 | µA | VOUT = 0 V; typ cell prints '<-1.0' | 4 | ||
| Output Saturation Voltage, Source Driver | VCE(SAT) | 1.7 | 2 | V | IOUT = -400 mA | 4 | |
| Output Saturation Voltage, Source Driver | VCE(SAT) | 1.8 | 2.1 | V | IOUT = -650 mA | 4 | |
| Output Saturation Voltage, Sink Driver | VCE(SAT) | 0.3 | 0.5 | V | IOUT = +400 mA, VS = 0.5 V | 4 | |
| Output Saturation Voltage, Sink Driver | VCE(SAT) | 0.7 | 1.3 | V | IOUT = +650 mA, VS = 0.5 V | 4 | |
| Clamp Diode Forward Voltage | VF | 1.1 | 1.4 | V | IF = 400 mA | 4 | |
| Clamp Diode Forward Voltage | VF | 1.4 | 1.6 | V | IF = 650 mA | 4 | |
| Motor Supply Current (No Load) | IBB(ON) | 3 | 5 | mA | VENABLE1 = VENABLE2 = 0.8 V | 4 | |
| Motor Supply Current (No Load) | IBB(OFF) | 200 | µA | VENABLE1 = VENABLE2 = 2.4 V; typ cell prints '<1.0' | 4 | ||
| Logic Supply Voltage Range | VCC | 4.75 | 5.5 | V | Operating | 4 | |
| Logic Input Voltage | VIN(1) | 2.4 | V | 4 | |||
| Logic Input Voltage | VIN(0) | 0.8 | V | 4 | |||
| Logic Input Current | IIN(1) | 20 | µA | VIN = 2.4 V; typ cell prints '<1.0' | 4 | ||
| Logic Input Current | IIN(0) | -200 | µA | VIN = 0.8 V; typ cell prints '<-20' | 4 | ||
| Reference Input Voltage Range | VREF | 0.1 | 2 | V | Operating | 4 | |
| Reference Input Current | IREF | -2.5 | 0 | 1 | µA | 4 | |
| Reference Divider Ratio | VREF/VTRIP | 3.8 | 4 | 4.2 | 4 | ||
| Current-Sense Comparator Input Offset Voltage | VIO | -6 | 0 | 6 | mV | VREF = 0 V | 4 |
| Current-Sense Comparator Input Voltage Range | VS | -0.3 | 1 | V | Operating | 4 | |
| Sense-Current Offset | ISO | 12 | 18 | 24 | mA | IS, IOUT, 50 mA ≤ IOUT ≤ 650 mA | 4 |
| PWM RC Frequency | fosc | 22.9 | 25.4 | 27.9 | kHz | CT = 680 pF, RT = 56 kΩ | 5 |
| PWM Propagation Delay Time | tPWM | 1 | 1.4 | µs | Comparator Trip to Source OFF | 5 | |
| PWM Propagation Delay Time | 0.8 | 1.2 | µs | Cycle Reset to Source ON | 5 | ||
| Cross-Over Dead Time | tcodt | 0.2 | 1.8 | 3 | µs | 1 kΩ Load to 25 V | 5 |
| UVLO Enable Threshold | VT(UVLO)+ | 4.1 | 4.6 | V | Increasing VCC | 5 | |
| UVLO Hysteresis | VT(UVLO)hys | 0.1 | 0.6 | V | 5 | ||
| Logic Supply Current | ICC(ON) | 50 | mA | VENABLE 1 = VENABLE 2 = 0.8 V | 5 | ||
| Logic Supply Current | ICC(OFF) | 9 | mA | VENABLE 1 = VENABLE 2 = 2.4 V | 5 | ||
| Load Supply Voltage | VBB | 30 | V | 2 | |||
| Logic Supply Voltage | VCC | 7 | V | 2 | |||
| Input Voltage | VIN | -0.3 | V | 2 | |||
| Sense Voltage | VS | 1 | V | 2 | |||
| Output Current, Peak | IOUT | -750 | 750 | mA | Peak; may be limited by duty cycle, ambient temperature, and heat sinking | 2 | |
| Output Current, Continuous | IOUT | -650 | 650 | mA | Continuous | 2 | |
| Package Power Dissipation | PD | 1.87 | W | TA = 25°C | 2 | ||
| Operating Ambient Temperature Range | TA | -20 | 85 | °C | Range S | 2 | |
| Maximum Junction Temperature | TJ(max) | 150 | °C | 2 | |||
| Storage Temperature | Tstg | -55 | 150 | °C | 2 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | These pins are at ground potential and need no electrical isolation. The device is lead (Pb) free, with 100% matte tin leadframe plating. | 2 |
CAD (Adom-generated)
- Symbol:
A3966SLBTR-T - Footprint:
Adom_Gen:Allegro_MicroSystems_A3966_e3f53c - 3D model: generated to fit the land (STEP)
- 3D model files:
a3966slbtr-t-etched.step/a3966slbtr-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);a3966slbtr-t.step/a3966slbtr-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Allegro MicroSystems, LLC datasheet (9 pp, sha256
353b83ce257a9954, retrieved 2026-11-13, tier: lcsc) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land. Land: Allegro A3966 p.7 'Package LB, 16-pin SOICW' (Reference Allegro DWG-0000388 Rev. 1, JEDEC MS-013AA), C 'PCB Layout Reference View': pads 2.25 x 0.65, 1.27 BSC pitch, 9.50 between pad-row centres, so pads at x +/-4.75. Body 10.21 ± 0.10 x 7.50 ± 0.10, tip to tip 10.31 ± 0.20, height 2.54 ± 0.10. (The drawing's note cites 'IPC7351 SOIC127P600X175-8M', an 8-pin narrow pattern name; the printed numbers are the wide 16-pin land and are used.)