3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownTL1963A-33KTTR
Texas Instruments · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · TO-263-5
TL1963A-33KTTR from Texas Instruments, in a TO-263-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SHDN | input | Driving SHDN above the 2V high-level input threshold enables the device and driving it below the 0.25V low-level threshold disables it, with a maximum SHDN voltage of 20V; connect it to VIN if independent shutdown control is not needed. |
| 2 | IN | power_in | Input supply pin, with a recommended input voltage range of 2.4V to 20V for the new chip and a recommended input capacitor of at least 1µF. |
| 3 | GND | power_in | Ground pin for the regulator, which must be connected to the system ground. |
| 4 | OUT | power_out | Regulator output that requires a capacitor of at least 10µF with ESR of 3Ω or less from OUT to ground for stability, placed as close to the pin as possible. |
| 5 | SENSE/ADJ | input | For the fixed-voltage TL1963A-33, this SENSE pin is the input to the error amplifier and should be connected to OUT for proper regulation, with its bias current specified as ISENSE. |
| 6 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TO-263-5 |
| Category | Power Management (PMIC) |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN minimum input voltage, Legacy Device (TL1963A-33) | VIN | 2.1 | 2.5 | V | ILOAD = 1.5A, TJ = -40°C to 125°C | 6 | |
| VIN minimum input voltage, New Chip | VIN | 2.4 | V | ILOAD = 1.5A, TJ = -40°C to 125°C | 6 | ||
| VUVLO (RISING), New Chip | VUVLO | 2 | 2.2 | 2.3 | V | VIN rising, IOUT = 10mA, TJ = -40°C to 125°C | 6 |
| VUVLO (FALLING), New Chip | VUVLO | 1.9 | 2.05 | 2.15 | V | VIN falling, IOUT = 10mA, TJ = -40°C to 125°C | 6 |
| VUVLO (HYST), New Chip | VUVLO (HYST) | 150 | mV | TJ = -40°C to 125°C | 6 | ||
| Regulated output voltage, Legacy Device, TL1963A-33 (25°C) | VOUT | 3.25 | 3.3 | 3.35 | V | VIN = 3.8V, ILOAD = 1mA, TJ = 25°C | 6 |
| Regulated output voltage, Legacy Device, TL1963A-33 (full range) | VOUT | 3.2 | 3.3 | 3.4 | V | VIN = 4.3V to 20V, ILOAD = 1mA to 1.5A, TJ = -40°C to 125°C | 6 |
| Regulated output voltage, New Chip, TL1963A-33 (25°C) | VOUT | 3.284 | 3.3 | 3.316 | V | VIN = 3.8V, ILOAD = 1mA, TJ = 25°C | 7 |
| Regulated output voltage, New Chip, TL1963A-33 (full range) | VOUT | 3.25 | 3.3 | 3.35 | V | VIN = 4.3V to 20V, ILOAD = 1mA to 1.5A, TJ = -40°C to 125°C | 7 |
| Line Regulation, Legacy Device, TL1963A-33 | 3.5 | 10 | mV | ΔVIN = 3.8V to 20V, ILOAD = 1mA | 7 | ||
| Line Regulation, New Chip, TL1963A-33 | 2.5 | 10 | mV | ΔVIN = 3.8V to 20V, ILOAD = 1mA | 7 | ||
| Load Regulation, Legacy Device, TL1963A-33 (full range) | 70 | mV | VIN = 4.3V, ΔILOAD = 1mA to 1.5A, TJ = -40°C to 125°C | 7 | |||
| Load Regulation, New Chip, TL1963A-33 (full range) | 16.5 | mV | VIN = 4.3V, ΔILOAD = 1mA to 1.5A, TJ = -40°C to 125°C | 7 | |||
| Dropout voltage (1.5A, 25°C) | VDO | 0.34 | 0.45 | V | TL1963A-33: VIN = 3.3V, ILOAD = 1.5A, TJ = 25°C | 8 | |
| Dropout voltage (1.5A, full range) | VDO | 0.55 | V | TL1963A-33: VIN = 3.3V, ILOAD = 1.5A, TJ = -40°C to 125°C | 8 | ||
| GND pin current, Legacy Device (0 mA load) | IGND | 1 | 1.5 | mA | VIN = VOUT (NOMINAL) + 1, ILOAD = 0mA, TJ = -40°C to 125°C | 8 | |
| GND pin current, Legacy Device (1.5 A load) | IGND | 80 | 120 | mA | VIN = VOUT (NOMINAL) + 1, ILOAD = 1.5A | 8 | |
| GND pin current, New Device (0 A load) | IGND | 1.2 | mA | VIN = VOUT (NOMINAL) + 1, ILOAD = 0A, TJ = -40°C to 125°C | 8 | ||
| GND pin current, New Device (1.5 A load) | IGND | 1.25 | mA | VIN = VOUT (NOMINAL) + 1, ILOAD = 1.5A | 8 | ||
| Output voltage noise, Legacy device | eN | 14 | µVRMS | COUT = 10µF, ILOAD = 1.5A, BW = 10Hz to 100kHz, VOUT = VADJ, TJ = 25°C | 8 | ||
| Output voltage noise, New Chip | eN | 23 | µVRMS | COUT = 10µF, ILOAD = 1.5A, BW = 10Hz to 100kHz, VOUT = VADJ, TJ = 25°C | 8 | ||
| Shutdown threshold (VOUT OFF to ON) | 0.9 | 2 | V | VOUT = OFF to ON, TJ = -40°C to 125°C | 8 | ||
| Shutdown threshold (VOUT ON to OFF) | 0.25 | 0.75 | V | VOUT = ON to OFF | 8 | ||
| SHDN pin current | ISHDN | 0.01 | 1 | µA | VSHDN = 0V, TJ = 25°C | 8 | |
| SHDN Quiescent current in shutdown, Legacy Device | IQ | 0.01 | 1 | µA | VIN = 6V, VSHDN = 0V, TJ = 25°C | 8 | |
| SHDN Quiescent current in shutdown, New Chip | IQ | 1.5 | µA | VIN = 6V, VSHDN = 0V, TJ = 25°C | 8 | ||
| Ripple Rejection, Legacy Chip | 55 | 63 | dB | VIN - VOUT = 1.5V (avg), VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 0.75A, TJ = 25°C | 8 | ||
| Ripple Rejection, New Chip | 53 | 60 | dB | VIN - VOUT = 1.5V (avg), VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 0.75A, TJ = 25°C | 8 | ||
| Current Limit, Legacy Device (full range) | ILIMIT | 1.6 | A | VIN = VOUT(NOMINAL) + 1V, TJ = -40°C to 125°C | 8 | ||
| Current Limit, New Chip (full range) | ILIMIT | 1.6 | A | VOUT forced at 0.9*VOUT(NOMINAL), TJ = -40°C to 125°C | 9 | ||
| Steady state reverse current, New Chip | IRC | 250 | µA | VOUT = 7V, VIN = 2.4V, TJ = -40°C to 125°C | 9 | ||
| Reverse current detection, New Chip | IR | 25 | mV | VOUT, VIN at which reverse current is detected, VOUT rising, VIN = 6V, TJ = -40°C to 125°C | 9 | ||
| Thermal shutdown temperature increasing | TSD+ | 150 | 161 | °C | 9 | ||
| Thermal shutdown temperature decreasing | TSD- | 130 | 141 | °C | 9 | ||
| Minimum input voltage (New Chip) | VIN | 2.4 | 20 | V | New chip | 5 | |
| Input voltage, Legacy Chip (minimum printed as VOUT + VDO) | VIN | 20 | V | Legacy chip | 5 | ||
| SHDN High Level Input Voltage | VIH | 2 | 20 | V | 5 | ||
| SHDN Low Level Input Voltage | VIL | 0.25 | V | 5 | |||
| Output current | IOUT | 0 | 1.5 | A | 5 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 5 | ||
| Input voltage (for legacy chip) | VIN | -20 | 20 | V | 5 | ||
| Input voltage (for new chip) | VIN | -0.3 | 20.2 | V | 5 | ||
| Output voltage (for legacy chip) | VOUT | -20 | 20 | V | 5 | ||
| Output voltage (for new chip, DCQ & KTT) | VOUT | -0.3 | 20 | V | 5 | ||
| Input-to-Output Differential (for legacy chip) | VIN-VOUT | -20 | 20 | V | 5 | ||
| Input-to-Output Differential (for new chip) | VIN-VOUT | -7 | 20 | V | 5 | ||
| Sense Voltage (for legacy chip) | VSENSE | -20 | 20 | V | 5 | ||
| Sense Voltage (for new chip) | VSENSE | -0.3 | 7 | V | 5 | ||
| SHDN Voltage (for legacy chip) | VSHDN | -20 | 20 | V | 5 | ||
| SHDN Voltage (for new chip) | VSHDN | -0.3 | 20 | V | 5 | ||
| Maximum lead temperature (10s soldering time) | TLEAD | 300 | °C | 10s soldering time | 5 | ||
| Operating junction temperature (for new chip) | TJ | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| Junction-to-ambient thermal resistance, Legacy Device | RθJA | 32.9 | °C/W | 6 | |||
| Junction-to-case (top) thermal resistance, Legacy Device | RθJC(top) | 37.6 | °C/W | 6 | |||
| Junction-to-board thermal resistance, Legacy Device | RθJB | 18.9 | °C/W | 6 | |||
| Junction-to-top characterization parameter, Legacy Device | ψJT | 5.7 | °C/W | 6 | |||
| Junction-to-board characterization parameter, Legacy Device | ψJB | 17.3 | °C/W | 6 | |||
| Junction-to-case (bottom) thermal resistance, Legacy Device | RθJC(bot) | 1 | °C/W | 6 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | ground return connections for the input and output capacitors as close to the GND pin as possible, using wide, component-side, copper planes. Do not use vias and long traces to create LDO circuit conn | 37 | |
| shell | copper | plane serves to provide accuracy of the output voltage and shield the LDO from noise. To improve the thermal performance of the device, and to maximize the current output at high ambient temperature, | 37 |
CAD (KiCad official)
- Symbol:
TL1963A-33KTTR - Footprint:
Package_TO_SOT_SMD:TO-263-5_TabPin6 - 3D model: TO-263-5 (KiCad packages3D, STEP)
- 3D model files:
tl1963a-33kttr-etched.step/tl1963a-33kttr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tl1963a-33kttr.step/tl1963a-33kttr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (60 pp, sha256
9a2da96a6fdaf2e5, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).