Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TL1963A-33KTTR

Texas Instruments · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · TO-263-5

TL1963A-33KTTR from Texas Instruments, in a TO-263-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SHDN input Driving SHDN above the 2V high-level input threshold enables the device and driving it below the 0.25V low-level threshold disables it, with a maximum SHDN voltage of 20V; connect it to VIN if independent shutdown control is not needed.
2 IN power_in Input supply pin, with a recommended input voltage range of 2.4V to 20V for the new chip and a recommended input capacitor of at least 1µF.
3 GND power_in Ground pin for the regulator, which must be connected to the system ground.
4 OUT power_out Regulator output that requires a capacitor of at least 10µF with ESR of 3Ω or less from OUT to ground for stability, placed as close to the pin as possible.
5 SENSE/ADJ input For the fixed-voltage TL1963A-33, this SENSE pin is the input to the error amplifier and should be connected to OUT for proper regulation, with its bias current specified as ISENSE.
6 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package TO-263-5
Category Power Management (PMIC)
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN minimum input voltage, Legacy Device (TL1963A-33) VIN 2.1 2.5 V ILOAD = 1.5A, TJ = -40°C to 125°C 6
VIN minimum input voltage, New Chip VIN 2.4 V ILOAD = 1.5A, TJ = -40°C to 125°C 6
VUVLO (RISING), New Chip VUVLO 2 2.2 2.3 V VIN rising, IOUT = 10mA, TJ = -40°C to 125°C 6
VUVLO (FALLING), New Chip VUVLO 1.9 2.05 2.15 V VIN falling, IOUT = 10mA, TJ = -40°C to 125°C 6
VUVLO (HYST), New Chip VUVLO (HYST) 150 mV TJ = -40°C to 125°C 6
Regulated output voltage, Legacy Device, TL1963A-33 (25°C) VOUT 3.25 3.3 3.35 V VIN = 3.8V, ILOAD = 1mA, TJ = 25°C 6
Regulated output voltage, Legacy Device, TL1963A-33 (full range) VOUT 3.2 3.3 3.4 V VIN = 4.3V to 20V, ILOAD = 1mA to 1.5A, TJ = -40°C to 125°C 6
Regulated output voltage, New Chip, TL1963A-33 (25°C) VOUT 3.284 3.3 3.316 V VIN = 3.8V, ILOAD = 1mA, TJ = 25°C 7
Regulated output voltage, New Chip, TL1963A-33 (full range) VOUT 3.25 3.3 3.35 V VIN = 4.3V to 20V, ILOAD = 1mA to 1.5A, TJ = -40°C to 125°C 7
Line Regulation, Legacy Device, TL1963A-33 3.5 10 mV ΔVIN = 3.8V to 20V, ILOAD = 1mA 7
Line Regulation, New Chip, TL1963A-33 2.5 10 mV ΔVIN = 3.8V to 20V, ILOAD = 1mA 7
Load Regulation, Legacy Device, TL1963A-33 (full range) 70 mV VIN = 4.3V, ΔILOAD = 1mA to 1.5A, TJ = -40°C to 125°C 7
Load Regulation, New Chip, TL1963A-33 (full range) 16.5 mV VIN = 4.3V, ΔILOAD = 1mA to 1.5A, TJ = -40°C to 125°C 7
Dropout voltage (1.5A, 25°C) VDO 0.34 0.45 V TL1963A-33: VIN = 3.3V, ILOAD = 1.5A, TJ = 25°C 8
Dropout voltage (1.5A, full range) VDO 0.55 V TL1963A-33: VIN = 3.3V, ILOAD = 1.5A, TJ = -40°C to 125°C 8
GND pin current, Legacy Device (0 mA load) IGND 1 1.5 mA VIN = VOUT (NOMINAL) + 1, ILOAD = 0mA, TJ = -40°C to 125°C 8
GND pin current, Legacy Device (1.5 A load) IGND 80 120 mA VIN = VOUT (NOMINAL) + 1, ILOAD = 1.5A 8
GND pin current, New Device (0 A load) IGND 1.2 mA VIN = VOUT (NOMINAL) + 1, ILOAD = 0A, TJ = -40°C to 125°C 8
GND pin current, New Device (1.5 A load) IGND 1.25 mA VIN = VOUT (NOMINAL) + 1, ILOAD = 1.5A 8
Output voltage noise, Legacy device eN 14 µVRMS COUT = 10µF, ILOAD = 1.5A, BW = 10Hz to 100kHz, VOUT = VADJ, TJ = 25°C 8
Output voltage noise, New Chip eN 23 µVRMS COUT = 10µF, ILOAD = 1.5A, BW = 10Hz to 100kHz, VOUT = VADJ, TJ = 25°C 8
Shutdown threshold (VOUT OFF to ON) 0.9 2 V VOUT = OFF to ON, TJ = -40°C to 125°C 8
Shutdown threshold (VOUT ON to OFF) 0.25 0.75 V VOUT = ON to OFF 8
SHDN pin current ISHDN 0.01 1 µA VSHDN = 0V, TJ = 25°C 8
SHDN Quiescent current in shutdown, Legacy Device IQ 0.01 1 µA VIN = 6V, VSHDN = 0V, TJ = 25°C 8
SHDN Quiescent current in shutdown, New Chip IQ 1.5 µA VIN = 6V, VSHDN = 0V, TJ = 25°C 8
Ripple Rejection, Legacy Chip 55 63 dB VIN - VOUT = 1.5V (avg), VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 0.75A, TJ = 25°C 8
Ripple Rejection, New Chip 53 60 dB VIN - VOUT = 1.5V (avg), VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 0.75A, TJ = 25°C 8
Current Limit, Legacy Device (full range) ILIMIT 1.6 A VIN = VOUT(NOMINAL) + 1V, TJ = -40°C to 125°C 8
Current Limit, New Chip (full range) ILIMIT 1.6 A VOUT forced at 0.9*VOUT(NOMINAL), TJ = -40°C to 125°C 9
Steady state reverse current, New Chip IRC 250 µA VOUT = 7V, VIN = 2.4V, TJ = -40°C to 125°C 9
Reverse current detection, New Chip IR 25 mV VOUT, VIN at which reverse current is detected, VOUT rising, VIN = 6V, TJ = -40°C to 125°C 9
Thermal shutdown temperature increasing TSD+ 150 161 °C 9
Thermal shutdown temperature decreasing TSD- 130 141 °C 9
Minimum input voltage (New Chip) VIN 2.4 20 V New chip 5
Input voltage, Legacy Chip (minimum printed as VOUT + VDO) VIN 20 V Legacy chip 5
SHDN High Level Input Voltage VIH 2 20 V 5
SHDN Low Level Input Voltage VIL 0.25 V 5
Output current IOUT 0 1.5 A 5
Operating junction temperature TJ -40 125 °C 5
Input voltage (for legacy chip) VIN -20 20 V 5
Input voltage (for new chip) VIN -0.3 20.2 V 5
Output voltage (for legacy chip) VOUT -20 20 V 5
Output voltage (for new chip, DCQ & KTT) VOUT -0.3 20 V 5
Input-to-Output Differential (for legacy chip) VIN-VOUT -20 20 V 5
Input-to-Output Differential (for new chip) VIN-VOUT -7 20 V 5
Sense Voltage (for legacy chip) VSENSE -20 20 V 5
Sense Voltage (for new chip) VSENSE -0.3 7 V 5
SHDN Voltage (for legacy chip) VSHDN -20 20 V 5
SHDN Voltage (for new chip) VSHDN -0.3 20 V 5
Maximum lead temperature (10s soldering time) TLEAD 300 °C 10s soldering time 5
Operating junction temperature (for new chip) TJ -40 150 °C 5
Storage temperature Tstg -65 150 °C 5
Junction-to-ambient thermal resistance, Legacy Device RθJA 32.9 °C/W 6
Junction-to-case (top) thermal resistance, Legacy Device RθJC(top) 37.6 °C/W 6
Junction-to-board thermal resistance, Legacy Device RθJB 18.9 °C/W 6
Junction-to-top characterization parameter, Legacy Device ψJT 5.7 °C/W 6
Junction-to-board characterization parameter, Legacy Device ψJB 17.3 °C/W 6
Junction-to-case (bottom) thermal resistance, Legacy Device RθJC(bot) 1 °C/W 6

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper ground return connections for the input and output capacitors as close to the GND pin as possible, using wide, component-side, copper planes. Do not use vias and long traces to create LDO circuit conn 37
shell copper plane serves to provide accuracy of the output voltage and shield the LDO from noise. To improve the thermal performance of the device, and to maximize the current output at high ambient temperature, 37

CAD (KiCad official)

  • Symbol: TL1963A-33KTTR
  • Footprint: Package_TO_SOT_SMD:TO-263-5_TabPin6
  • 3D model: TO-263-5 (KiCad packages3D, STEP)
  • 3D model files: tl1963a-33kttr-etched.step / tl1963a-33kttr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tl1963a-33kttr.step / tl1963a-33kttr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (60 pp, sha256 9a2da96a6fdaf2e5, retrieved 2026-11-10, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF