Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LM5046SQ

Texas Instruments · AC-DC Controllers & Regulators · WQFN-28-EP(5x5)

LM5046SQ from Texas Instruments, in a WQFN-28-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SLOPE output Ramping current source from 0 to 100 µA for slope compensation in current mode control; tie to ground if slope compensation is not required.
2 COMP input Opto-coupler input to the PWM: zero input current gives maximum duty cycle and 1 mA reduces the duty cycle to zero.
3 REF output 5 V reference output with a maximum output current of 15 mA, locally decoupled with a 0.1 µF capacitor.
4 RT/SYNC input Resistor between RT and AGND sets the oscillator frequency; synchronization requires an AC-coupled pulse raising the pin at least 1.5 V above the 2 V nominal bias level.
5 AGND power_in Analog ground, to be connected directly to the power ground.
6 RD1 input Resistor between RD1 and AGND sets the delay from the falling edge of HO1/SR1 or LO1/SR2 to the rising edge of LO1 or HO1 respectively.
7 RD2 input Resistor between RD2 and AGND sets the delay from the falling edge of LO2 or HO2 to the rising edge of HO2 or LO2 respectively.
8 RES input Restart timer: when CS exceeds the 750 mV limit, 30 µA is sourced into the RES capacitor, and at 1.0 V the SS capacitor is discharged to disable the outputs.
9 SS input Soft-start pin charged by an internal 20 µA source; pulling it below 200 mV stops PWM pulses at HO1,2 and LO1,2 and turns off the synchronous rectifiers.
10 SSSR input Sets the synchronous rectifier soft-start ramp with an external capacitor and internal 20 µA source, enabled after the first output pulse when SS > 2 V and Icomp < 800 µA.
11 SSOFF input Connect to AGND for soft-stop on VIN UVLO and hiccup-mode current limit, or to REF for a hard stop on any fault.
12 HS2 output Switch node common to the high-side FET source, low-side FET drain and transformer primary winding.
13 HO2 output High-side PWM output driving the upper bridge MOSFET with 1.5 A peak source and 2 A peak sink current.
14 BST2 power_out Bootstrap capacitor between BST2 and HS2 provides bias for the high-side HO2 driver; BST1/BST2 to HS1/HS2 must not exceed 16 V.
15 SR2 output Synchronous rectifier gate control output capable of 100 mA peak source and 400 mA peak sink.
16 LO2 output Low-side PWM gate driver output with 1.5 A peak source and 2 A peak sink current.
17 VCC power_out Start-up regulator output initially regulated to 9.5 V and reduced to 7.7 V once SSSR reaches 1 V; external bias of 10 V to 14 V is recommended, absolute maximum 16 V.
18 PGND power_in Power ground, to be connected directly to analog ground.
19 LO1 output Low-side PWM gate driver output with 1.5 A peak source and 2 A peak sink current.
20 SR1 output Synchronous rectifier gate control output capable of 100 mA peak source and 400 mA peak sink.
21 BST1 power_out Bootstrap capacitor between BST1 and HS1 provides bias for the high-side HO1 driver; an external diode from VCC charges it when HS1 is low.
22 HO1 output High-side PWM output driving the upper bridge MOSFET with 1.5 A peak source and 2 A peak sink current.
23 HS1 output Switch node common to the high-side FET source, low-side FET drain and transformer primary winding.
24 VIN power_in Input to the start-up regulator with an operating range of 14 V to 100 V; outside this range VCC can be biased directly by an external regulator.
25 UVLO input External divider sets the shutdown and standby levels; VCC and REF enable at 0.4 V, SS releases at 1.25 V, with 20 µA hysteresis.
26 OVP input External divider sets the overvoltage shutdown level with a 1.25 V threshold and 20 µA hysteresis; an NTC divider may be used for temperature shutdown.
27 RAMP input Modulation ramp for the PWM comparator (current mode or feed-forward voltage mode), reset to GND at the end of every cycle.
28 CS input Current sense input: when CS exceeds 750 mV the PWM pulse is terminated for cycle-by-cycle current limit, and an internal switch holds CS low for 40 ns after either output switches high.
29 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WQFN-28-EP(5x5)
Category Power Supply Chip
Pins 29

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN Voltage VIN 14 100 V over operating free-air temperature range 6
External Voltage Applied to VCC 10 14 V over operating free-air temperature range 6
Junction Temperature TJ -40 125 °C over operating free-air temperature range 6
SLOPE -0.3 2 V over operating free-air temperature range 6
VIN to GND VIN -0.3 105 V 6
HS to GND HS -5 105 V 6
BST1/BST2 to GND BST1/BST2 -0.3 116 V 6
BST1/BST2 to HS1/HS2 BST1/BST2-HS1/HS2 -0.3 16 V 6
HO1/HO2 to HS1/HS2 HO1/HO2 -0.3 V 6
LO1/LO2/SR1/SR2 LO1/LO2/SR1/SR2 -0.3 V 6
VCC to GND VCC -0.3 16 V 6
REF, SSOFF, RT, OVP, UVLO to GND REF, SSOFF, RT, OVP, UVLO -0.3 7 V 6
RAMP RAMP -0.3 7 V 6
COMP COMP -0.3 V 6
COMP Input Current 10 mA 6
All other inputs to GND -0.3 V 6
Junction Temperature TJ 150 °C 6
VCC voltage (SSSR < 1 V) VCC1 9.3 9.6 9.9 V ICC= 10 mA (SSSR < 1 V) 7
VCC voltage (SSSR > 1 V) VCC2 7.5 7.8 8.1 V ICC= 10 mA (SSSR > 1 V) 7
VCC current limit ICC(Lim) 60 80 mA VCC= 6 V 7
VCC under-voltage threshold, negative going VCC VCC(UV) 5.9 6.3 6.7 V Negative going VCC 7
VIN shutdown current 300 520 µA VIN = 20 V, VUVLO = 0 V 7
VIN shutdown current 350 550 µA VVIN = 100 V, VUVLO = 0 V 7
REF voltage VREF 4.85 5 5.15 V IREF = 0 mA 7
REF current limit IREF(Lim) 15 20 mA VREF = 4.5 V 7
VREF under-voltage threshold, positive going VREF VREFUV 4.3 4.5 4.7 V Positive going VREF 7
UVLO under-voltage threshold VUVLO 1.18 1.25 1.32 V 7
Under-voltage standby enable threshold 0.32 0.4 0.48 V UVLO voltage rising 7
UVLO hysteresis current IUVLO 16 20 24 µA UVLO pin sinking current when VUVLO < 1.25 V 7
OVP shutdown threshold VOVP 1.18 1.25 1.32 V OVP rising 7
OVP hysteresis current 16 20 24 µA OVP sources current when OVP > 1.25 V 7
SS charge current ISS 16 20 24 µA VSS = 0 V 7
SS threshold for SSSR charge current enable 1.93 2 2.2 V ICOMP < 800 µA 7
SSSR charge current ISSSR 16 20 24 µA VSS > 2 V, ICOMP < 800 µA 8
SSSR discharge current 1 ISSSR-DIS1 54 65 75 µA VUVLO < 1.25 V 8
Current limit threshold VCS 0.71 0.75 0.785 V 8
SSOFF Input Threshold VIH(min) 2.8 V 8
Frequency (LO1, half oscillator frequency) FSW1 185 200 215 kHz RT = 25 kΩ 8
Frequency (LO1, half oscillator frequency) FSW2 420 480 540 kHz RT = 10 kΩ 8
RT sync threshold 2.8 3 3.3 V 8
TPA: HO1/SR1 turn-off to LO1 turn-on; LO1/SR2 turn-off to HO1 turn-on TPA 39 65 89 ns RD1 = 20 kΩ 8
TPA: HO1/SR1 turn-off to LO1 turn-on; LO1/SR2 turn-off to HO1 turn-on TPA 230 300 391 ns RD1 = 100 kΩ 8
TAP: LO2 turn-off to HO2 turn-on; HO2 turn-off to LO2 turn-on TAP 27 55 78 ns RD2 = 20 kΩ 8
TAP: LO2 turn-off to HO2 turn-on; HO2 turn-off to LO2 turn-on TAP 214 300 378 ns RD2 = 100 kΩ 8
COMP current to RAMP offset VPWM-OS 680 800 940 µA VRAMP = 0 V 8
SS to RAMP offset VSS-OS 0.78 1 1.22 V VRAMP = 0 V 8
BST under-voltage threshold VBst uv 3.8 4.7 5.6 V VBST, VHS rising 9
Low-state output voltage (HO1, HO2, LO1, LO2) VOL 0.16 0.32 V IHO/LO = 100 mA 9
High-state output voltage (HO1, HO2, LO1, LO2) VOH 0.27 0.495 V IHO/LO = 100 mA 9
Peak Source Current (HO1, HO2, LO1, LO2) IOHL 1.5 A VHO/LO = 0 V 9
Peak Sink Current (HO1, HO2, LO1, LO2) IOLL 2 A VHO/LO = VCC 9
Low-state output voltage (SR1, SR2) VOL 0.05 0.1 V ISR1/SR2 = 10 mA 9
High-state output voltage (SR1, SR2) VOH 0.17 0.28 V ISR1/SR2 = 10 mA, VOH = VREF, VSR 9
Peak Source Current (SR1, SR2) IOHL 0.1 A VSR = 0 V 9
Peak Sink Current (SR1, SR2) IOLL 0.4 A VSR = VREF 9
COMP for SSSR charge current enable 690 800 915 µA VSS > 2 V 9
Junction-to-ambient thermal resistance (RSG/WQFN column) RθJA 37.4 °C/W RSG package column 7
Junction-to-case (top) thermal resistance (RSG/WQFN column) RθJC(top) 21.8 °C/W RSG package column 7
Junction-to-board thermal resistance (RSG/WQFN column) RθJB 10.1 °C/W RSG package column 7
Junction-to-case (bottom) thermal resistance (RSG/WQFN column) RθJC(bot) 2.6 °C/W RSG package column 7

CAD (KiCad official)

  • Symbol: LM5046SQ
  • Footprint: Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm
  • 3D model: WQFN-28-EP(5x5) (KiCad packages3D, STEP)
  • 3D model files: lm5046sq-etched.step / lm5046sq-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm5046sq.step / lm5046sq.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (49 pp, sha256 8dc1fece0dbb9db8, retrieved 2026-10-28, tier: manufacturer)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF