Generated by kicad-footprint-generator · KiCad file format 20260206
LM5046SQ
Texas Instruments · AC-DC Controllers & Regulators · WQFN-28-EP(5x5)
LM5046SQ from Texas Instruments, in a WQFN-28-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SLOPE | output | Ramping current source from 0 to 100 µA for slope compensation in current mode control; tie to ground if slope compensation is not required. |
| 2 | COMP | input | Opto-coupler input to the PWM: zero input current gives maximum duty cycle and 1 mA reduces the duty cycle to zero. |
| 3 | REF | output | 5 V reference output with a maximum output current of 15 mA, locally decoupled with a 0.1 µF capacitor. |
| 4 | RT/SYNC | input | Resistor between RT and AGND sets the oscillator frequency; synchronization requires an AC-coupled pulse raising the pin at least 1.5 V above the 2 V nominal bias level. |
| 5 | AGND | power_in | Analog ground, to be connected directly to the power ground. |
| 6 | RD1 | input | Resistor between RD1 and AGND sets the delay from the falling edge of HO1/SR1 or LO1/SR2 to the rising edge of LO1 or HO1 respectively. |
| 7 | RD2 | input | Resistor between RD2 and AGND sets the delay from the falling edge of LO2 or HO2 to the rising edge of HO2 or LO2 respectively. |
| 8 | RES | input | Restart timer: when CS exceeds the 750 mV limit, 30 µA is sourced into the RES capacitor, and at 1.0 V the SS capacitor is discharged to disable the outputs. |
| 9 | SS | input | Soft-start pin charged by an internal 20 µA source; pulling it below 200 mV stops PWM pulses at HO1,2 and LO1,2 and turns off the synchronous rectifiers. |
| 10 | SSSR | input | Sets the synchronous rectifier soft-start ramp with an external capacitor and internal 20 µA source, enabled after the first output pulse when SS > 2 V and Icomp < 800 µA. |
| 11 | SSOFF | input | Connect to AGND for soft-stop on VIN UVLO and hiccup-mode current limit, or to REF for a hard stop on any fault. |
| 12 | HS2 | output | Switch node common to the high-side FET source, low-side FET drain and transformer primary winding. |
| 13 | HO2 | output | High-side PWM output driving the upper bridge MOSFET with 1.5 A peak source and 2 A peak sink current. |
| 14 | BST2 | power_out | Bootstrap capacitor between BST2 and HS2 provides bias for the high-side HO2 driver; BST1/BST2 to HS1/HS2 must not exceed 16 V. |
| 15 | SR2 | output | Synchronous rectifier gate control output capable of 100 mA peak source and 400 mA peak sink. |
| 16 | LO2 | output | Low-side PWM gate driver output with 1.5 A peak source and 2 A peak sink current. |
| 17 | VCC | power_out | Start-up regulator output initially regulated to 9.5 V and reduced to 7.7 V once SSSR reaches 1 V; external bias of 10 V to 14 V is recommended, absolute maximum 16 V. |
| 18 | PGND | power_in | Power ground, to be connected directly to analog ground. |
| 19 | LO1 | output | Low-side PWM gate driver output with 1.5 A peak source and 2 A peak sink current. |
| 20 | SR1 | output | Synchronous rectifier gate control output capable of 100 mA peak source and 400 mA peak sink. |
| 21 | BST1 | power_out | Bootstrap capacitor between BST1 and HS1 provides bias for the high-side HO1 driver; an external diode from VCC charges it when HS1 is low. |
| 22 | HO1 | output | High-side PWM output driving the upper bridge MOSFET with 1.5 A peak source and 2 A peak sink current. |
| 23 | HS1 | output | Switch node common to the high-side FET source, low-side FET drain and transformer primary winding. |
| 24 | VIN | power_in | Input to the start-up regulator with an operating range of 14 V to 100 V; outside this range VCC can be biased directly by an external regulator. |
| 25 | UVLO | input | External divider sets the shutdown and standby levels; VCC and REF enable at 0.4 V, SS releases at 1.25 V, with 20 µA hysteresis. |
| 26 | OVP | input | External divider sets the overvoltage shutdown level with a 1.25 V threshold and 20 µA hysteresis; an NTC divider may be used for temperature shutdown. |
| 27 | RAMP | input | Modulation ramp for the PWM comparator (current mode or feed-forward voltage mode), reset to GND at the end of every cycle. |
| 28 | CS | input | Current sense input: when CS exceeds 750 mV the PWM pulse is terminated for cycle-by-cycle current limit, and an internal switch holds CS low for 40 ns after either output switches high. |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-28-EP(5x5) |
| Category | Power Supply Chip |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN Voltage | VIN | 14 | 100 | V | over operating free-air temperature range | 6 | |
| External Voltage Applied to VCC | 10 | 14 | V | over operating free-air temperature range | 6 | ||
| Junction Temperature | TJ | -40 | 125 | °C | over operating free-air temperature range | 6 | |
| SLOPE | -0.3 | 2 | V | over operating free-air temperature range | 6 | ||
| VIN to GND | VIN | -0.3 | 105 | V | 6 | ||
| HS to GND | HS | -5 | 105 | V | 6 | ||
| BST1/BST2 to GND | BST1/BST2 | -0.3 | 116 | V | 6 | ||
| BST1/BST2 to HS1/HS2 | BST1/BST2-HS1/HS2 | -0.3 | 16 | V | 6 | ||
| HO1/HO2 to HS1/HS2 | HO1/HO2 | -0.3 | V | 6 | |||
| LO1/LO2/SR1/SR2 | LO1/LO2/SR1/SR2 | -0.3 | V | 6 | |||
| VCC to GND | VCC | -0.3 | 16 | V | 6 | ||
| REF, SSOFF, RT, OVP, UVLO to GND | REF, SSOFF, RT, OVP, UVLO | -0.3 | 7 | V | 6 | ||
| RAMP | RAMP | -0.3 | 7 | V | 6 | ||
| COMP | COMP | -0.3 | V | 6 | |||
| COMP Input Current | 10 | mA | 6 | ||||
| All other inputs to GND | -0.3 | V | 6 | ||||
| Junction Temperature | TJ | 150 | °C | 6 | |||
| VCC voltage (SSSR < 1 V) | VCC1 | 9.3 | 9.6 | 9.9 | V | ICC= 10 mA (SSSR < 1 V) | 7 |
| VCC voltage (SSSR > 1 V) | VCC2 | 7.5 | 7.8 | 8.1 | V | ICC= 10 mA (SSSR > 1 V) | 7 |
| VCC current limit | ICC(Lim) | 60 | 80 | mA | VCC= 6 V | 7 | |
| VCC under-voltage threshold, negative going VCC | VCC(UV) | 5.9 | 6.3 | 6.7 | V | Negative going VCC | 7 |
| VIN shutdown current | 300 | 520 | µA | VIN = 20 V, VUVLO = 0 V | 7 | ||
| VIN shutdown current | 350 | 550 | µA | VVIN = 100 V, VUVLO = 0 V | 7 | ||
| REF voltage | VREF | 4.85 | 5 | 5.15 | V | IREF = 0 mA | 7 |
| REF current limit | IREF(Lim) | 15 | 20 | mA | VREF = 4.5 V | 7 | |
| VREF under-voltage threshold, positive going VREF | VREFUV | 4.3 | 4.5 | 4.7 | V | Positive going VREF | 7 |
| UVLO under-voltage threshold | VUVLO | 1.18 | 1.25 | 1.32 | V | 7 | |
| Under-voltage standby enable threshold | 0.32 | 0.4 | 0.48 | V | UVLO voltage rising | 7 | |
| UVLO hysteresis current | IUVLO | 16 | 20 | 24 | µA | UVLO pin sinking current when VUVLO < 1.25 V | 7 |
| OVP shutdown threshold | VOVP | 1.18 | 1.25 | 1.32 | V | OVP rising | 7 |
| OVP hysteresis current | 16 | 20 | 24 | µA | OVP sources current when OVP > 1.25 V | 7 | |
| SS charge current | ISS | 16 | 20 | 24 | µA | VSS = 0 V | 7 |
| SS threshold for SSSR charge current enable | 1.93 | 2 | 2.2 | V | ICOMP < 800 µA | 7 | |
| SSSR charge current | ISSSR | 16 | 20 | 24 | µA | VSS > 2 V, ICOMP < 800 µA | 8 |
| SSSR discharge current 1 | ISSSR-DIS1 | 54 | 65 | 75 | µA | VUVLO < 1.25 V | 8 |
| Current limit threshold | VCS | 0.71 | 0.75 | 0.785 | V | 8 | |
| SSOFF Input Threshold | VIH(min) | 2.8 | V | 8 | |||
| Frequency (LO1, half oscillator frequency) | FSW1 | 185 | 200 | 215 | kHz | RT = 25 kΩ | 8 |
| Frequency (LO1, half oscillator frequency) | FSW2 | 420 | 480 | 540 | kHz | RT = 10 kΩ | 8 |
| RT sync threshold | 2.8 | 3 | 3.3 | V | 8 | ||
| TPA: HO1/SR1 turn-off to LO1 turn-on; LO1/SR2 turn-off to HO1 turn-on | TPA | 39 | 65 | 89 | ns | RD1 = 20 kΩ | 8 |
| TPA: HO1/SR1 turn-off to LO1 turn-on; LO1/SR2 turn-off to HO1 turn-on | TPA | 230 | 300 | 391 | ns | RD1 = 100 kΩ | 8 |
| TAP: LO2 turn-off to HO2 turn-on; HO2 turn-off to LO2 turn-on | TAP | 27 | 55 | 78 | ns | RD2 = 20 kΩ | 8 |
| TAP: LO2 turn-off to HO2 turn-on; HO2 turn-off to LO2 turn-on | TAP | 214 | 300 | 378 | ns | RD2 = 100 kΩ | 8 |
| COMP current to RAMP offset | VPWM-OS | 680 | 800 | 940 | µA | VRAMP = 0 V | 8 |
| SS to RAMP offset | VSS-OS | 0.78 | 1 | 1.22 | V | VRAMP = 0 V | 8 |
| BST under-voltage threshold | VBst uv | 3.8 | 4.7 | 5.6 | V | VBST, VHS rising | 9 |
| Low-state output voltage (HO1, HO2, LO1, LO2) | VOL | 0.16 | 0.32 | V | IHO/LO = 100 mA | 9 | |
| High-state output voltage (HO1, HO2, LO1, LO2) | VOH | 0.27 | 0.495 | V | IHO/LO = 100 mA | 9 | |
| Peak Source Current (HO1, HO2, LO1, LO2) | IOHL | 1.5 | A | VHO/LO = 0 V | 9 | ||
| Peak Sink Current (HO1, HO2, LO1, LO2) | IOLL | 2 | A | VHO/LO = VCC | 9 | ||
| Low-state output voltage (SR1, SR2) | VOL | 0.05 | 0.1 | V | ISR1/SR2 = 10 mA | 9 | |
| High-state output voltage (SR1, SR2) | VOH | 0.17 | 0.28 | V | ISR1/SR2 = 10 mA, VOH = VREF, VSR | 9 | |
| Peak Source Current (SR1, SR2) | IOHL | 0.1 | A | VSR = 0 V | 9 | ||
| Peak Sink Current (SR1, SR2) | IOLL | 0.4 | A | VSR = VREF | 9 | ||
| COMP for SSSR charge current enable | 690 | 800 | 915 | µA | VSS > 2 V | 9 | |
| Junction-to-ambient thermal resistance (RSG/WQFN column) | RθJA | 37.4 | °C/W | RSG package column | 7 | ||
| Junction-to-case (top) thermal resistance (RSG/WQFN column) | RθJC(top) | 21.8 | °C/W | RSG package column | 7 | ||
| Junction-to-board thermal resistance (RSG/WQFN column) | RθJB | 10.1 | °C/W | RSG package column | 7 | ||
| Junction-to-case (bottom) thermal resistance (RSG/WQFN column) | RθJC(bot) | 2.6 | °C/W | RSG package column | 7 |
CAD (KiCad official)
- Symbol:
LM5046SQ - Footprint:
Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm - 3D model: WQFN-28-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
lm5046sq-etched.step/lm5046sq-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm5046sq.step/lm5046sq.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (49 pp, sha256
8dc1fece0dbb9db8, retrieved 2026-10-28, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).