Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

STM32L151RBT6ATR

STMicroelectronics · ST Microelectronics · LQFP-64(10x10)

STM32L151RBT6ATR from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VLCD power_in LCD power supply pin; on STM32L151xxxxA devices the datasheet says this pin should be connected to VDD.
2 PC13 bidirectional 5 V tolerant GPIO (FT) with RTC_TAMP1, RTC_TS, RTC_OUT and WKUP2 functions.
3 PC14-OSC32_IN bidirectional Standard 3.3 V I/O (TC) that serves as OSC32_IN only when the LSE oscillator is on, otherwise usable as PC14.
4 PC15-OSC32_OUT bidirectional Standard 3.3 V I/O (TC) that serves as OSC32_OUT only when the LSE oscillator is on, otherwise usable as PC15.
5 PH0-OSC_IN bidirectional Standard 3.3 V I/O (TC) that serves as OSC_IN only when the HSE oscillator is on, otherwise usable as PH0.
6 PH1-OSC_OUT bidirectional Standard 3.3 V I/O (TC) that serves as OSC_OUT only when the HSE oscillator is on, otherwise usable as PH1.
7 NRST bidirectional Bidirectional reset pin with embedded weak pull-up resistor.
8 PC0 bidirectional 5 V tolerant I/O (FT) with LCD_SEG18, ADC_IN10 and COMP1_INP functions.
9 PC1 bidirectional 5 V tolerant I/O (FT) with LCD_SEG19, ADC_IN11 and COMP1_INP functions.
10 PC2 bidirectional 5 V tolerant I/O (FT) with LCD_SEG20, ADC_IN12 and COMP1_INP functions.
11 PC3 bidirectional Standard 3.3 V I/O (TC) with LCD_SEG21, ADC_IN13 and COMP1_INP functions.
12 VSSA power_in Analog ground pin.
13 VDDA power_in Analog supply pin; the datasheet gives VDDA from 1.8 V to 3.6 V.
14 PA0-WKUP1 bidirectional 5 V tolerant I/O (FT) with USART2_CTS, TIM2_CH1_ETR, WKUP1, ADC_IN0, COMP1_INP and RTC_TAMP2 functions.
15 PA1 bidirectional 5 V tolerant I/O (FT) with USART2_RTS, TIM2_CH2, LCD_SEG0, ADC_IN1 and COMP1_INP functions.
16 PA2 bidirectional 5 V tolerant I/O (FT) with USART2_TX, TIM2_CH3, TIM9_CH1, LCD_SEG1, ADC_IN2 and COMP1_INP functions.
17 PA3 bidirectional Standard 3.3 V I/O (TC) with USART2_RX, TIM2_CH4, TIM9_CH2, LCD_SEG2, ADC_IN3 and COMP1_INP functions.
18 VSS_4 power_in Ground pin.
19 VDD_4 power_in Digital supply pin.
20 PA4 bidirectional Standard 3.3 V I/O (TC) with SPI1_NSS, USART2_CK, ADC_IN4, DAC_OUT1 and COMP1_INP functions.
21 PA5 bidirectional Standard 3.3 V I/O (TC) with SPI1_SCK, TIM2_CH1_ETR, ADC_IN5, DAC_OUT2 and COMP1_INP functions.
22 PA6 bidirectional 5 V tolerant I/O (FT) with SPI1_MISO, TIM3_CH1, LCD_SEG3, TIM10_CH1, ADC_IN6 and COMP1_INP functions.
23 PA7 bidirectional 5 V tolerant I/O (FT) with SPI1_MOSI, TIM3_CH2, LCD_SEG4, TIM11_CH1, ADC_IN7 and COMP1_INP functions.
24 PC4 bidirectional 5 V tolerant I/O (FT) with LCD_SEG22, ADC_IN14 and COMP1_INP functions.
25 PC5 bidirectional 5 V tolerant I/O (FT) with LCD_SEG23, ADC_IN15 and COMP1_INP functions.
26 PB0 bidirectional Standard 3.3 V I/O (TC) with TIM3_CH3, LCD_SEG5, ADC_IN8, COMP1_INP and VREF_OUT functions.
27 PB1 bidirectional 5 V tolerant I/O (FT) with TIM3_CH4, LCD_SEG6, ADC_IN9, COMP1_INP and VREF_OUT functions.
28 PB2 bidirectional 5 V tolerant I/O (FT) that also serves as BOOT1, with VLCDRAIL1 function.
29 PB10 bidirectional 5 V tolerant I/O (FT) with I2C2_SCL, USART3_TX, TIM2_CH3 and LCD_SEG10 functions.
30 PB11 bidirectional 5 V tolerant I/O (FT) with I2C2_SDA, USART3_RX, TIM2_CH4 and LCD_SEG11 functions.
31 VSS_1 power_in Ground pin.
32 VDD_1 power_in Digital supply pin.
33 PB12 bidirectional 5 V tolerant I/O (FT) with SPI2_NSS, I2C2_SMBA, USART3_CK, LCD_SEG12, TIM10_CH1, ADC_IN18, COMP1_INP and VLCDRAIL2 functions.
34 PB13 bidirectional 5 V tolerant I/O (FT) with SPI2_SCK, USART3_CTS, LCD_SEG13, TIM9_CH1, ADC_IN19 and COMP1_INP functions.
35 PB14 bidirectional 5 V tolerant I/O (FT) with SPI2_MISO, USART3_RTS, LCD_SEG14, TIM9_CH2, ADC_IN20 and COMP1_INP functions.
36 PB15 bidirectional 5 V tolerant I/O (FT) with SPI2_MOSI, LCD_SEG15, TIM11_CH1, ADC_IN21, COMP1_INP and RTC_REFIN functions.
37 PC6 bidirectional 5 V tolerant I/O (FT) with TIM3_CH1 and LCD_SEG24 functions.
38 PC7 bidirectional 5 V tolerant I/O (FT) with TIM3_CH2 and LCD_SEG25 functions.
39 PC8 bidirectional 5 V tolerant I/O (FT) with TIM3_CH3 and LCD_SEG26 functions.
40 PC9 bidirectional 5 V tolerant I/O (FT) with TIM3_CH4 and LCD_SEG27 functions.
41 PA8 bidirectional 5 V tolerant I/O (FT) with USART1_CK, MCO and LCD_COM0 functions.
42 PA9 bidirectional 5 V tolerant I/O (FT) with USART1_TX and LCD_COM1 functions.
43 PA10 bidirectional 5 V tolerant I/O (FT) with USART1_RX and LCD_COM2 functions.
44 PA11 bidirectional 5 V tolerant I/O (FT) with USART1_CTS, SPI1_MISO and USB_DM functions.
45 PA12 bidirectional 5 V tolerant I/O (FT) with USART1_RTS, SPI1_MOSI and USB_DP functions.
46 PA13 bidirectional 5 V tolerant I/O (FT) whose reset function is JTMS-SWDIO (serial wire debug data).
47 VSS_2 power_in Ground pin.
48 VDD_2 power_in Digital supply pin.
49 PA14 bidirectional 5 V tolerant I/O (FT) whose reset function is JTCK-SWCLK (serial wire debug clock).
50 PA15 bidirectional 5 V tolerant I/O (FT) with JTDI, TIM2_CH1_ETR, SPI1_NSS and LCD_SEG17 functions.
51 PC10 bidirectional 5 V tolerant I/O (FT) with USART3_TX, LCD_SEG28, LCD_SEG40 and LCD_COM4 functions.
52 PC11 bidirectional 5 V tolerant I/O (FT) with USART3_RX, LCD_SEG29, LCD_SEG41 and LCD_COM5 functions.
53 PC12 bidirectional 5 V tolerant I/O (FT) with USART3_CK, LCD_SEG30, LCD_SEG42 and LCD_COM6 functions.
54 PD2 bidirectional 5 V tolerant I/O (FT) with TIM3_ETR, LCD_SEG31, LCD_SEG43 and LCD_COM7 functions.
55 PB3 bidirectional 5 V tolerant I/O (FT) with JTDO, TIM2_CH2, SPI1_SCK, LCD_SEG7 and COMP2_INM functions.
56 PB4 bidirectional 5 V tolerant I/O (FT) with NJTRST, TIM3_CH1, SPI1_MISO, LCD_SEG8 and COMP2_INP functions.
57 PB5 bidirectional 5 V tolerant I/O (FT) with I2C1_SMBA, TIM3_CH2, SPI1_MOSI, LCD_SEG9 and COMP2_INP functions.
58 PB6 bidirectional 5 V tolerant I/O (FT) with I2C1_SCL, TIM4_CH1 and USART1_TX functions.
59 PB7 bidirectional 5 V tolerant I/O (FT) with I2C1_SDA, TIM4_CH2, USART1_RX and PVD_IN functions.
60 BOOT0 input Dedicated BOOT0 pin used to select the boot mode.
61 PB8 bidirectional 5 V tolerant I/O (FT) with TIM4_CH3, I2C1_SCL, LCD_SEG16 and TIM10_CH1 functions.
62 PB9 bidirectional 5 V tolerant I/O (FT) with TIM4_CH4, I2C1_SDA, LCD_COM3 and TIM11_CH1 functions.
63 VSS_3 power_in Ground pin.
64 VDD_3 power_in Digital supply pin.

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package LQFP-64(10x10)
Category Embedded Processors & Controllers
Pins 64

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
External main supply voltage VDD-VSS -0.3 4 V including VDDA and VDD 55
Input voltage on five-volt tolerant pin VIN -0.3 V VSS − 0.3 to VDD+4.0 55
Input voltage on any other pin VIN -0.3 4 V VSS −0.3 to 4.0 55
Total current into all VDD_x power lines ΣIVDD 100 mA source 55
Total current out of all VSS_x ground lines ΣIVSS 100 mA sink 55
Maximum current into each VDD_x pin IVDD(PIN) 70 mA source 55
Output current sunk by any I/O and control pin IIO 25 mA 55
Storage temperature range TSTG -65 150 °C 56
Maximum junction temperature TJ 150 °C 56
Standard operating voltage VDD 1.65 3.6 V BOR detector disabled 56
Standard operating voltage, BOR enabled VDD 1.8 3.6 V BOR detector enabled, at power on 56
Analog operating voltage (ADC or DAC used) VDDA 1.8 3.6 V Must be the same voltage as VDD 56
Internal AHB clock frequency fHCLK 0 32 MHz 56
Power dissipation LQFP64 PD 444 mW TA = 85 °C for suffix 6, LQFP64 package 57
Ambient temperature, suffix 6 TA -40 85 °C Maximum power dissipation 57
Junction temperature range, suffix 6 TJ -40 105 °C 6 suffix version 57
Power on/power down reset threshold, falling VPOR/PDR 1 1.5 1.65 V Falling edge 57
Power on/power down reset threshold, rising VPOR/PDR 1.3 1.5 1.65 V Rising edge 57
Reset temporization, BOR enabled TRSTTEMPO 2 3.3 ms VDD rising, BOR enabled 57
Brown-out reset threshold 0, falling VBOR0 1.67 1.7 1.74 V Falling edge 58
Brown-out reset threshold 4, falling VBOR4 2.68 2.8 2.85 V Falling edge 58
Internal reference voltage VREFINT out 1.202 1.224 1.242 V , 40 °C < TJ < +110 °C 59
Internal reference current consumption IREFINT 1.4 2.3 µA 59
Internal reference startup time TVREFINT 2 3 ms 59
Temperature coefficient of VREFINT TCoeff 25 100 ppm/°C -40 °C < TJ < +110 °C 59
Run mode current from Flash, Range 3, 1 MHz IDD (Run from Flash) 215 285 µA Range 3, VCORE=1.2 V, fHCLK 1 MHz 61
Run mode current from Flash, Range 1, 32 MHz IDD (Run from Flash) 8.25 9.6 mA Range 1, VCORE=1.8 V, 32 MHz 61
Run mode current from RAM, Range 1, 32 MHz IDD (Run from RAM) 7.15 8.5 mA Range 1, VCORE=1.8 V, 32 MHz 62
Sleep mode current, Flash OFF, Range 1, 32 MHz IDD (Sleep) 1600 2350 µA Range 1, VCORE=1.8 V, 32 MHz, Flash OFF 63
Low-power run current, RAM, 32 kHz, TA -40 to 25 °C IDD (LP Run) 10.9 12 µA MSI 65 kHz, fHCLK = 32 kHz, code from RAM, TA = -40 °C to 25 °C 64
Low-power run current, RAM, 32 kHz, 85 °C IDD (LP Run) 16.5 23 µA MSI 65 kHz, fHCLK = 32 kHz, code from RAM, TA = 85 °C 64
Max allowed current in Low-power run mode IDD Max (LP Run) 200 µA VDD from 1.65 V to 3.6 V 64
Low-power sleep current, Flash ON, 32 kHz IDD (LP Sleep) 15 16 µA MSI 65 kHz, fHCLK = 32 kHz, Flash ON, TA = -40 °C to 25 °C 65
Stop mode with RTC (LSI), LCD OFF, 25 °C IDD (Stop with RTC) 1.38 4 µA RTC clocked by LSI, LCD OFF, TA = -40°C to 25°C 66
Stop mode current, RTC disabled, 25 °C IDD (Stop) 0.434 1 µA Regulator in LP mode, LSI, HSI and HSE OFF, TA = -40°C to 25°C 67
Stop mode current, RTC disabled, 105 °C IDD (Stop) 6.84 22 µA Regulator in LP mode, LSI, HSI and HSE OFF, TA = 105°C 67
Standby mode with RTC (LSI), 25 °C IDD (Standby with RTC) 1.11 1.9 µA RTC clocked by LSI, TA = -40 °C to 25 °C 68
Standby mode current, RTC disabled, 25 °C IDD (Standby) 0.277 0.6 µA Independent watchdog and LSI OFF, TA = -40 °C to 25 °C 68
Standby mode current, RTC disabled, 105 °C IDD (Standby) 1.09 7 µA Independent watchdog and LSI OFF, TA = 105 °C 68
Wakeup from Stop mode, regulator in LP mode, Range 1 and 2 tWUSTOP 7.7 8.9 µs fHCLK = fMSI = 4.2 MHz, Voltage Range 1 and 2 71
Wakeup from Standby mode, FWU bit = 1 tWUSTDBY 58 104 µs FWU bit = 1, fHCLK = MSI = 2.1 MHz 71
Wakeup from Standby mode, FWU bit = 0 tWUSTDBY 2.6 3.25 ms FWU bit = 0, fHCLK = MSI = 2.1 MHz 71
HSE user external clock frequency, CSS on or PLL used fHSE_ext 1 32 MHz CSS is on or PLL is used 72
HSE oscillator frequency fOSC_IN 1 24 MHz 73
LSE user external clock frequency fLSE_ext 1 32.768 1000 kHz 73
HSI frequency fHSI 16 MHz VDD = 3.0 V 77
HSI accuracy, VDDA = 1.65 V to 3.6 V ACCHSI -4 3 % VDDA = 1.65 V to 3.6 V, TA = -40 to 105 °C 77
LSI frequency fLSI 26 38 56 kHz 77
PLL input clock fPLL_IN 2 24 MHz 79
PLL output clock fPLL_OUT 2 32 MHz 79
PLL lock time tLOCK 115 160 µs PLL input = 16 MHz, PLL VCO = 96 MHz 79
Flash/EEPROM operating voltage VDD 1.65 3.6 V Read / Write / Erase 80
Flash programming time tprog 3.28 3.94 ms Programming 80
Flash cycling endurance, program memory NCYC 10 kcycles TA = -40°C to 105 °C 80
ESD voltage HBM VESD(HBM) 2000 V TA = +25 °C, JESD22-A114 82
Input low level voltage, TC and FT I/O VIL 0.3 V TC and FT I/O, printed as 0.3 VDD 84
Weak pull-up equivalent resistor RPU 25 45 65 kΩ VIN = VSS 84
Output low level voltage, IIO = 8 mA VOL 0.4 V IIO = 8 mA, 2.7 V < VDD < 3.6 V 85

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin TLEAD Maximum lead temperature during soldering see note (1) 1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb assembly), the ST ECOPACK® 56

CAD (KiCad official)

  • Symbol: STM32L151RBT6ATR
  • Footprint: Package_QFP:LQFP-64_10x10mm_P0.5mm
  • 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
  • 3D model files: stm32l151rbt6atr-etched.step / stm32l151rbt6atr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stm32l151rbt6atr.step / stm32l151rbt6atr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (130 pp, sha256 e5e0ab791f4e7879, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF