component
TPS61378QWRTERQ1
Public Made by Adomby adom
Texas Instruments DC-DC Converters, WQFN-16-EP(3x3). Datasheet-verified pinout, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
README
markdownTPS61378QWRTERQ1
Texas Instruments · DC-DC Converters · WQFN-16-EP(3x3)
TPS61378QWRTERQ1 from Texas Instruments, in a WQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Power supply input ranging from 2.3 V to 14 V with 25 to 35 μA quiescent current |
| 2 | BST | input | Bootstrap supply for high-side FET gate driver; ceramic capacitor must connect between this pin and SW pin |
| 3 | SW | output | Switching node connected to low-side FET drain and high-side FET source, actively driven at 200 kHz to 2.2 MHz |
| 4 | SW | output | Switching node connected to low-side FET drain and high-side FET source, actively driven at 200 kHz to 2.2 MHz |
| 5 | MODE/SYNC | input | Mode selection for forced PWM mode (logic high) or auto PFM mode (logic low or floating); supports external clock synchronization |
| 6 | VCC | power_out | Regulated 4.8 V output; 1 μF minimum ceramic capacitor required to GND |
| 7 | GND | power_in | Power ground of IC connected to low-side FET source; must connect to ground plane and thermal pad |
| 8 | GND | power_in | Power ground of IC connected to low-side FET source; must connect to ground plane and thermal pad |
| 9 | VO | power_out | Output of isolation FET for load connection to achieve input/output galvanic isolation |
| 10 | OUT | power_out | Output of high-side FET drain; connect this pin or short with VO pin to enable load disconnect and short protection features |
| 11 | PG | output | Open-drain power good indicator output; pulled high 2.5 to 4.3 ms after VOUT reaches 90% of target voltage |
| 12 | ILIM | input | Current limit setting pin; connect resistor to GND to program peak current limit from 1 A to 4.8 A |
| 13 | FB | input | Feedback input pin; use resistor divider to set desired output voltage between 4.0 V and 18.5 V |
| 14 | COMP | input | Compensation network connection for external RC network to optimize loop stability and transient response |
| 15 | EN | input | Enable logic input; device active when pulled above 1.2 V threshold |
| 16 | FREQ | input | Frequency setting pin; connect resistor to GND to program switching frequency from 200 kHz to 2.2 MHz |
| 17 | Thermal Pad | passive | Exposed thermal pad; must solder to power ground plane for efficient junction heat dissipation |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-16-EP(3x3) |
| Category | Power Management (PMIC) |
| Pins | 17 |
CAD (KiCad official)
- Symbol:
TPS61378QWRTERQ1 - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: WQFN-16-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
tps61378qwrterq1-etched.step/tps61378qwrterq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps61378qwrterq1.step/tps61378qwrterq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (42 pp, sha256
3799e162e33f3792, retrieved 2026-09-23, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).