3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT6553IGN#PBF
Analog Devices · Video Amplifiers · SSOP-16
LT6553IGN#PBF from Analog Devices, in a SSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Enable control pin with internal 46k pull-up that turns the part off if unconnected, and pulling it low enables the part (TTL compatible, referenced to DGND, VEN - VDGND ≤ 5.5V). |
| 2 | DGND | power_in | Digital ground reference for the EN pin, normally connected to ground, with V+ - VDGND ≥ 3V required. |
| 3 | INR | input | Red channel input with nominal impedance of 400kΩ and no internal termination resistor. |
| 4 | AGND | power_in | Analog ground for the 370Ω gain resistor of the red channel amplifier. |
| 5 | ING | input | Green channel input with nominal impedance of 400kΩ and no internal termination resistor. |
| 6 | AGND | power_in | Analog ground shared by the 370Ω gain resistors of the green and blue channel amplifiers, where additional resistance increases green/blue crosstalk. |
| 7 | INB | input | Blue channel input with nominal impedance of 400kΩ and no internal termination resistor. |
| 8 | V- | power_in | Negative supply voltage, not internally connected to the other V- pins so all must be connected externally with proper bypassing. |
| 9 | V- | power_in | Negative supply voltage for the blue channel output stage, not internally connected to other V- pins and must be connected externally with proper bypassing. |
| 10 | OUTB | output | Blue channel output at twice the blue input (gain of 2), performing optimally with a 150Ω load. |
| 11 | V+ | power_in | Positive supply voltage for the output stages of amplifiers B and G, not internally connected to other V+ pins and must be connected externally with proper bypassing. |
| 12 | OUTG | output | Green channel output at twice the green input (gain of 2), performing optimally with a 150Ω load. |
| 13 | V- | power_in | Negative supply voltage for the output stages of amplifiers G and R, not internally connected to other supply pins and must be connected externally with proper bypassing. |
| 14 | OUTR | output | Red channel output at twice the red input (gain of 2), performing optimally with a 150Ω load. |
| 15 | V+ | power_in | Positive supply voltage for the output stage of amplifier R, not internally connected to other V+ pins and must be connected externally with proper bypassing. |
| 16 | V+ | power_in | Positive supply voltage, not internally connected to other V+ pins and must be connected externally with proper bypassing. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SSOP-16 |
| Category | Operational Amplifier/Comparator |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Total Supply Voltage (V+ to V-) | 13.2 | V | 2 | ||||
| Input Current | -10 | 10 | mA | Note 2 | 2 | ||
| Output Current (Continuous) | -70 | 70 | mA | 2 | |||
| EN to DGND Voltage | 5.5 | V | Note 2 | 2 | |||
| Operating Temperature Range | -40 | 85 | °C | Note 4 | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Junction Temperature | TJMAX | 150 | °C | 2 | |||
| Lead Temperature (Soldering, 10 sec) | 300 | °C | 2 | ||||
| Thermal Resistance Junction to Ambient | θJA | 135 | °C/W | GN package | 2 | ||
| Input Referred Offset Voltage | VOS | -10 | 3 | 10 | mV | VIN = 0V, VOS = VOUT/2 | 2 |
| Input Referred Offset Voltage (full temp) | VOS | -20 | 20 | mV | VIN = 0V, VOS = VOUT/2, over full operating temperature range | 2 | |
| Input Current | IIN | -50 | -17 | 50 | µA | over full operating temperature range | 2 |
| Input Resistance | RIN | 150 | 400 | kΩ | VIN = ±1V | 2 | |
| Power Supply Rejection Ratio | PSRR | 56 | 62 | dB | VS (Total) = 4.5V to 12V (Note 6) | 2 | |
| Input Current Power Supply Rejection | IPSRR | -4 | 1 | 4 | µA/V | VS (Total) = 4.5V to 12V (Note 6) | 2 |
| Gain Error | AV ERR | -5 | -1.2 | 5 | % | VOUT = ±2V | 2 |
| Gain Matching | AV MATCH | -1 | 1 | % | Any One Channel to Another | 2 | |
| Maximum Output Voltage Swing | VOUT | 3.25 | 3.5 | V | ±, 25°C | 2 | |
| Maximum Output Voltage Swing (full temp) | VOUT | 3.1 | V | ±, over full operating temperature range | 2 | ||
| Supply Current, Per Amplifier | IS | 8 | 11 | mA | 2 | ||
| Supply Current, Per Amplifier (full temp) | IS | 14 | mA | over full operating temperature range | 2 | ||
| Supply Current, Disabled, Total | 22 | 100 | µA | VEN = 4V | 2 | ||
| Supply Current, Disabled, Total | 0.5 | 100 | µA | VEN = Open | 2 | ||
| Enable Pin Current | IEN | -200 | -95 | µA | VEN = 0.4V | 2 | |
| Enable Pin Current | IEN | 0.5 | 50 | µA | VEN = V+ | 2 | |
| Output Short-Circuit Current | ISC | 50 | 105 | mA | RL = 0Ω, VIN = ±1V | 2 | |
| Slew Rate | SR | 1700 | 2500 | V/µs | ±1V on ±2V Output Step (Note 9) | 2 | |
| Full Power Bandwidth 2V | FPBW | 270 | 400 | MHz | VOUT = 2VP-P (Note 7) | 3 | |
| Small Signal -3dB Bandwidth | -3dB BW | 650 | MHz | VOUT = 200mVP-P | 2 | ||
| Gain Flatness ±0.1dB Bandwidth | 0.1dB BW | 150 | MHz | VOUT = 200mVP-P | 2 | ||
| Input Capacitance | CIN | 1 | pF | f = 100kHz | 2 | ||
| Full Power Bandwidth 4V | FPBW | 200 | MHz | VOUT = 4VP-P (Note 7) | 3 | ||
| All-Hostile Crosstalk | -75 | dB | f = 10MHz, VOUT = 2VP-P | 3 | |||
| All-Hostile Crosstalk | -50 | dB | f = 100MHz, VOUT = 2VP-P | 3 | |||
| Settling Time | tS | 6 | ns | 0.1% of VFINAL, VSTEP = 2V | 3 | ||
| Small-Signal Rise and Fall Time | tR, tF | 550 | ps | 10% to 90%, VOUT = 200mVP-P | 3 | ||
| Differential Gain | dG | 0.022 | % | Note 8 | 3 | ||
| Differential Phase | dP | 0.006 | Deg | Note 8 | 3 | ||
| 2nd Harmonic Distortion | HD2 | -82 | dBc | f = 10MHz, VOUT = 2VP-P | 3 | ||
| 3rd Harmonic Distortion | HD3 | -72 | dBc | f = 10MHz, VOUT = 2VP-P | 3 |
CAD (KiCad official)
- Symbol:
LT6553IGN#PBF - Footprint:
Package_SO:SSOP-16_5.3x6.2mm_P0.65mm - 3D model: SSOP-16 (KiCad packages3D, STEP)
- 3D model files:
lt6553ign-etched.step/lt6553ign-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt6553ign.step/lt6553ign.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (12 pp, sha256
673fd420e4d2fec9, retrieved 2026-11-18) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).