Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT6553IGN#PBF

Analog Devices · Video Amplifiers · SSOP-16

LT6553IGN#PBF from Analog Devices, in a SSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 EN input Enable control pin with internal 46k pull-up that turns the part off if unconnected, and pulling it low enables the part (TTL compatible, referenced to DGND, VEN - VDGND ≤ 5.5V).
2 DGND power_in Digital ground reference for the EN pin, normally connected to ground, with V+ - VDGND ≥ 3V required.
3 INR input Red channel input with nominal impedance of 400kΩ and no internal termination resistor.
4 AGND power_in Analog ground for the 370Ω gain resistor of the red channel amplifier.
5 ING input Green channel input with nominal impedance of 400kΩ and no internal termination resistor.
6 AGND power_in Analog ground shared by the 370Ω gain resistors of the green and blue channel amplifiers, where additional resistance increases green/blue crosstalk.
7 INB input Blue channel input with nominal impedance of 400kΩ and no internal termination resistor.
8 V- power_in Negative supply voltage, not internally connected to the other V- pins so all must be connected externally with proper bypassing.
9 V- power_in Negative supply voltage for the blue channel output stage, not internally connected to other V- pins and must be connected externally with proper bypassing.
10 OUTB output Blue channel output at twice the blue input (gain of 2), performing optimally with a 150Ω load.
11 V+ power_in Positive supply voltage for the output stages of amplifiers B and G, not internally connected to other V+ pins and must be connected externally with proper bypassing.
12 OUTG output Green channel output at twice the green input (gain of 2), performing optimally with a 150Ω load.
13 V- power_in Negative supply voltage for the output stages of amplifiers G and R, not internally connected to other supply pins and must be connected externally with proper bypassing.
14 OUTR output Red channel output at twice the red input (gain of 2), performing optimally with a 150Ω load.
15 V+ power_in Positive supply voltage for the output stage of amplifier R, not internally connected to other V+ pins and must be connected externally with proper bypassing.
16 V+ power_in Positive supply voltage, not internally connected to other V+ pins and must be connected externally with proper bypassing.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package SSOP-16
Category Operational Amplifier/Comparator
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Total Supply Voltage (V+ to V-) 13.2 V 2
Input Current -10 10 mA Note 2 2
Output Current (Continuous) -70 70 mA 2
EN to DGND Voltage 5.5 V Note 2 2
Operating Temperature Range -40 85 °C Note 4 2
Storage Temperature Range -65 150 °C 2
Junction Temperature TJMAX 150 °C 2
Lead Temperature (Soldering, 10 sec) 300 °C 2
Thermal Resistance Junction to Ambient θJA 135 °C/W GN package 2
Input Referred Offset Voltage VOS -10 3 10 mV VIN = 0V, VOS = VOUT/2 2
Input Referred Offset Voltage (full temp) VOS -20 20 mV VIN = 0V, VOS = VOUT/2, over full operating temperature range 2
Input Current IIN -50 -17 50 µA over full operating temperature range 2
Input Resistance RIN 150 400 kΩ VIN = ±1V 2
Power Supply Rejection Ratio PSRR 56 62 dB VS (Total) = 4.5V to 12V (Note 6) 2
Input Current Power Supply Rejection IPSRR -4 1 4 µA/V VS (Total) = 4.5V to 12V (Note 6) 2
Gain Error AV ERR -5 -1.2 5 % VOUT = ±2V 2
Gain Matching AV MATCH -1 1 % Any One Channel to Another 2
Maximum Output Voltage Swing VOUT 3.25 3.5 V ±, 25°C 2
Maximum Output Voltage Swing (full temp) VOUT 3.1 V ±, over full operating temperature range 2
Supply Current, Per Amplifier IS 8 11 mA 2
Supply Current, Per Amplifier (full temp) IS 14 mA over full operating temperature range 2
Supply Current, Disabled, Total 22 100 µA VEN = 4V 2
Supply Current, Disabled, Total 0.5 100 µA VEN = Open 2
Enable Pin Current IEN -200 -95 µA VEN = 0.4V 2
Enable Pin Current IEN 0.5 50 µA VEN = V+ 2
Output Short-Circuit Current ISC 50 105 mA RL = 0Ω, VIN = ±1V 2
Slew Rate SR 1700 2500 V/µs ±1V on ±2V Output Step (Note 9) 2
Full Power Bandwidth 2V FPBW 270 400 MHz VOUT = 2VP-P (Note 7) 3
Small Signal -3dB Bandwidth -3dB BW 650 MHz VOUT = 200mVP-P 2
Gain Flatness ±0.1dB Bandwidth 0.1dB BW 150 MHz VOUT = 200mVP-P 2
Input Capacitance CIN 1 pF f = 100kHz 2
Full Power Bandwidth 4V FPBW 200 MHz VOUT = 4VP-P (Note 7) 3
All-Hostile Crosstalk -75 dB f = 10MHz, VOUT = 2VP-P 3
All-Hostile Crosstalk -50 dB f = 100MHz, VOUT = 2VP-P 3
Settling Time tS 6 ns 0.1% of VFINAL, VSTEP = 2V 3
Small-Signal Rise and Fall Time tR, tF 550 ps 10% to 90%, VOUT = 200mVP-P 3
Differential Gain dG 0.022 % Note 8 3
Differential Phase dP 0.006 Deg Note 8 3
2nd Harmonic Distortion HD2 -82 dBc f = 10MHz, VOUT = 2VP-P 3
3rd Harmonic Distortion HD3 -72 dBc f = 10MHz, VOUT = 2VP-P 3

CAD (KiCad official)

  • Symbol: LT6553IGN#PBF
  • Footprint: Package_SO:SSOP-16_5.3x6.2mm_P0.65mm
  • 3D model: SSOP-16 (KiCad packages3D, STEP)
  • 3D model files: lt6553ign-etched.step / lt6553ign-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt6553ign.step / lt6553ign.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (12 pp, sha256 673fd420e4d2fec9, retrieved 2026-11-18)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-opus-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF