3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSTM32F091CCT6
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · LQFP-48(7x7)
STM32F091CCT6 from STMicroelectronics, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup power supply for the RTC, the external 32 kHz oscillator and the backup registers when VDD is not present, specified at 1.65 to 3.6 V. |
| 2 | PC13 | bidirectional | Standard 3.3 V I/O (TC) supplied through the power switch, which sinks only 3 mA, so output use is limited to 2 MHz with a 30 pF maximum load and it must not source current to an LED; also WKUP2, RTC_TAMP1, RTC_TS and RTC_OUT. |
| 3 | PC14-OSC32_IN | bidirectional | Standard 3.3 V I/O (TC) supplied through the same 3 mA power switch as PC13 with the same output limits, and used as OSC32_IN for the 32.768 kHz LSE oscillator. |
| 4 | PC15-OSC32_OUT | bidirectional | Standard 3.3 V I/O (TC) supplied through the same 3 mA power switch as PC13 with the same output limits, and used as OSC32_OUT for the 32.768 kHz LSE oscillator. |
| 5 | PF0-OSC_IN | bidirectional | 5 V-tolerant I/O (FTf, Fm+ capable) with alternate functions CRS_SYNC and I2C1_SDA, and used as OSC_IN for the 4 to 32 MHz external HSE oscillator. |
| 6 | PF1-OSC_OUT | bidirectional | 5 V-tolerant I/O (FTf, Fm+ capable) with alternate function I2C1_SCL, and used as OSC_OUT for the external HSE oscillator. |
| 7 | NRST | bidirectional | Bidirectional active-low device reset input and internal reset output with an embedded weak pull-up of 25 to 55 kΩ (40 kΩ typical). |
| 8 | VSSA | power_in | Analog ground pin. |
| 9 | VDDA | power_in | Analog power supply, which must be equal to or higher than VDD, with a minimum of 2.4 V when the ADC or DAC is used and a maximum of 3.6 V. |
| 10 | PA0 | bidirectional | 3.3 V-tolerant I/O (TTa) connected directly to the ADC, with alternate functions USART2_CTS, TIM2_CH1_ETR, TSC_G1_IO1, USART4_TX and COMP1_OUT, and additional functions ADC_IN0, WKUP1, RTC_TAMP2 and COMP1_INM6. |
| 11 | PA1 | bidirectional | 3.3 V-tolerant I/O (TTa) connected directly to the ADC, with alternate functions USART2_RTS, TIM2_CH2, TIM15_CH1N, TSC_G1_IO2, USART4_RX and EVENTOUT, and additional functions ADC_IN1 and COMP1_INP. |
| 12 | PA2 | bidirectional | 3.3 V-tolerant I/O (TTa) connected directly to the ADC, with alternate functions USART2_TX, TIM2_CH3, TIM15_CH1, TSC_G1_IO3 and COMP2_OUT, and additional functions ADC_IN2, WKUP4 and COMP2_INM6. |
| 13 | PA3 | bidirectional | 3.3 V-tolerant I/O (TTa) connected directly to the ADC, with alternate functions USART2_RX, TIM2_CH4, TIM15_CH2 and TSC_G1_IO4, and additional functions ADC_IN3 and COMP2_INP. |
| 14 | PA4 | bidirectional | 3.3 V-tolerant I/O (TTa) connected directly to the ADC, with alternate functions SPI1_NSS, I2S1_WS, USART2_CK, TSC_G2_IO1, TIM14_CH1 and USART6_TX, and additional functions ADC_IN4, DAC_OUT1, COMP1_INM4 and COMP2_INM4. |
| 15 | PA5 | bidirectional | 3.3 V-tolerant I/O (TTa) connected directly to the ADC, with alternate functions SPI1_SCK, I2S1_CK, CEC, TIM2_CH1_ETR, TSC_G2_IO2 and USART6_RX, and additional functions ADC_IN5, DAC_OUT2, COMP1_INM5 and COMP2_INM5. |
| 16 | PA6 | bidirectional | 3.3 V-tolerant I/O (TTa) connected directly to the ADC, with alternate functions SPI1_MISO, I2S1_MCK, TIM3_CH1, TIM1_BKIN, TIM16_CH1, COMP1_OUT, TSC_G2_IO3, EVENTOUT and USART3_CTS, and additional function ADC_IN6. |
| 17 | PA7 | bidirectional | 3.3 V-tolerant I/O (TTa) connected directly to the ADC, with alternate functions SPI1_MOSI, I2S1_SD, TIM3_CH2, TIM14_CH1, TIM1_CH1N, TIM17_CH1, COMP2_OUT, TSC_G2_IO4 and EVENTOUT, and additional function ADC_IN7. |
| 18 | PB0 | bidirectional | 3.3 V-tolerant I/O (TTa) connected directly to the ADC, with alternate functions TIM3_CH3, TIM1_CH2N, TSC_G3_IO2, EVENTOUT and USART3_CK, and additional function ADC_IN8. |
| 19 | PB1 | bidirectional | 3.3 V-tolerant I/O (TTa) connected directly to the ADC, with alternate functions TIM3_CH4, USART3_RTS, TIM14_CH1, TIM1_CH3N and TSC_G3_IO3, and additional function ADC_IN9. |
| 20 | PB2 | bidirectional | 5 V-tolerant I/O (FT) with alternate function TSC_G3_IO4. |
| 21 | PB10 | bidirectional | 5 V-tolerant I/O (FTf, Fm+ capable) with alternate functions SPI2_SCK, I2S2_CK, I2C2_SCL, USART3_TX, CEC, TSC_SYNC and TIM2_CH3. |
| 22 | PB11 | bidirectional | 5 V-tolerant I/O (FTf, Fm+ capable) with alternate functions USART3_RX, TIM2_CH4, EVENTOUT, TSC_G6_IO1 and I2C2_SDA. |
| 23 | VSS | power_in | Ground pin. |
| 24 | VDD | power_in | Digital power supply, 2.0 to 3.6 V, which also feeds the internal regulator. |
| 25 | PB12 | bidirectional | 5 V-tolerant I/O (FT) with alternate functions TIM1_BKIN, TIM15_BKIN, SPI2_NSS, I2S2_WS, USART3_CK, TSC_G6_IO2 and EVENTOUT. |
| 26 | PB13 | bidirectional | 5 V-tolerant I/O (FTf, Fm+ capable) with alternate functions SPI2_SCK, I2S2_CK, I2C2_SCL, USART3_CTS, TIM1_CH1N and TSC_G6_IO3. |
| 27 | PB14 | bidirectional | 5 V-tolerant I/O (FTf, Fm+ capable) with alternate functions SPI2_MISO, I2S2_MCK, I2C2_SDA, USART3_RTS, TIM1_CH2N, TIM15_CH1 and TSC_G6_IO4. |
| 28 | PB15 | bidirectional | 5 V-tolerant I/O (FT) with alternate functions SPI2_MOSI, I2S2_SD, TIM1_CH3N, TIM15_CH1N and TIM15_CH2, and additional functions WKUP7 and RTC_REFIN. |
| 29 | PA8 | bidirectional | 5 V-tolerant I/O (FT) supplied by VDDIO2, with alternate functions USART1_CK, TIM1_CH1, EVENTOUT, MCO and CRS_SYNC. |
| 30 | PA9 | bidirectional | 5 V-tolerant I/O (FT) supplied by VDDIO2, with alternate functions USART1_TX, TIM1_CH2, TIM15_BKIN, MCO, TSC_G4_IO1 and I2C1_SCL. |
| 31 | PA10 | bidirectional | 5 V-tolerant I/O (FT) supplied by VDDIO2, with alternate functions USART1_RX, TIM1_CH3, TIM17_BKIN, TSC_G4_IO2 and I2C1_SDA. |
| 32 | PA11 | bidirectional | 5 V-tolerant I/O (FT) supplied by VDDIO2, with alternate functions CAN_RX, USART1_CTS, TIM1_CH4, COMP1_OUT, TSC_G4_IO3, EVENTOUT and I2C2_SCL. |
| 33 | PA12 | bidirectional | 5 V-tolerant I/O (FT) supplied by VDDIO2, with alternate functions CAN_TX, USART1_RTS, TIM1_ETR, COMP2_OUT, TSC_G4_IO4, EVENTOUT and I2C2_SDA. |
| 34 | PA13 | bidirectional | 5 V-tolerant I/O (FT) supplied by VDDIO2 that after reset is the SWDIO alternate function with internal pull-up enabled, also with alternate function IR_OUT. |
| 35 | VSS | power_in | Ground pin. |
| 36 | VDDIO2 | power_in | Digital I/O supply for the marked I/Os, 1.65 to 3.6 V, which must not be supplied without a valid VDD supply. |
| 37 | PA14 | bidirectional | 5 V-tolerant I/O (FT) supplied by VDDIO2 that after reset is the SWCLK alternate function with internal pull-down enabled, also with alternate function USART2_TX. |
| 38 | PA15 | bidirectional | 5 V-tolerant I/O (FT) supplied by VDDIO2, with alternate functions SPI1_NSS, I2S1_WS, USART2_RX, USART4_RTS, TIM2_CH1_ETR and EVENTOUT. |
| 39 | PB3 | bidirectional | 5 V-tolerant I/O (FT) with alternate functions SPI1_SCK, I2S1_CK, TIM2_CH2, TSC_G5_IO1, EVENTOUT and USART5_TX. |
| 40 | PB4 | bidirectional | 5 V-tolerant I/O (FT) with alternate functions SPI1_MISO, I2S1_MCK, TIM17_BKIN, TIM3_CH1, TSC_G5_IO2, EVENTOUT and USART5_RX. |
| 41 | PB5 | bidirectional | 5 V-tolerant I/O (FT) with alternate functions SPI1_MOSI, I2S1_SD, I2C1_SMBA, TIM16_BKIN, TIM3_CH2 and USART5_CK_RTS, and additional function WKUP6. |
| 42 | PB6 | bidirectional | 5 V-tolerant I/O (FTf, Fm+ capable) with alternate functions I2C1_SCL, USART1_TX, TIM16_CH1N and TSC_G5_IO3. |
| 43 | PB7 | bidirectional | 5 V-tolerant I/O (FTf, Fm+ capable) with alternate functions I2C1_SDA, USART1_RX, USART4_CTS, TIM17_CH1N and TSC_G5_IO4. |
| 44 | PF11-BOOT0 | bidirectional | 5 V-tolerant I/O (FT) that also provides the BOOT0 boot memory selection input. |
| 45 | PB8 | bidirectional | 5 V-tolerant I/O (FTf, Fm+ capable) with alternate functions I2C1_SCL, CEC, TIM16_CH1, TSC_SYNC and CAN_RX. |
| 46 | PB9 | bidirectional | 5 V-tolerant I/O (FTf, Fm+ capable) with alternate functions SPI2_NSS, I2S2_WS, I2C1_SDA, IR_OUT, TIM17_CH1, EVENTOUT and CAN_TX. |
| 47 | VSS | power_in | Ground pin. |
| 48 | VDD | power_in | Digital power supply, 2.0 to 3.6 V, which also feeds the internal regulator. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-48(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage | VDD-VSS | -0.3 | 4 | V | 52 | ||
| External I/O supply voltage | VDDIO2-VSS | -0.3 | 4 | V | 52 | ||
| External analog supply voltage | VDDA-VSS | -0.3 | 4 | V | 52 | ||
| Allowed voltage difference for VDD > VDDA | VDD-VDDA | 0.4 | V | 52 | |||
| External backup supply voltage | VBAT-VSS | -0.3 | 4 | V | 52 | ||
| Input voltage on FT and FTf pins | VIN | -0.3 | V | Printed max VDDIOx + 4.0 (not numeric); valid only if internal pull-up/pull-down disabled, otherwise 4 V | 52 | ||
| Input voltage on TTa pins | VIN | -0.3 | 4 | V | 52 | ||
| Input voltage on any other pin | VIN | -0.3 | 4 | V | 52 | ||
| Variations between different VDD power pins | /∆VDDx/ | 50 | mV | 52 | |||
| Variations between all the different ground pins | /VSSx - VSS/ | 50 | mV | 52 | |||
| Total current into sum of all VDD power lines (source) | ΣIVDD | 120 | mA | 53 | |||
| Total current out of sum of all VSS ground lines (sink) | ΣIVSS | -120 | mA | 53 | |||
| Maximum current into each VDD power pin (source) | IVDD(PIN) | 100 | mA | 53 | |||
| Maximum current out of each VSS ground pin (sink) | IVSS(PIN) | -100 | mA | 53 | |||
| Output current sunk by any I/O and control pin | IIO(PIN) | 25 | mA | 53 | |||
| Output current sourced by any I/O and control pin | IIO(PIN) | -25 | mA | 53 | |||
| Total output current sunk by sum of all I/Os and control pins | ΣIIO(PIN) | 80 | mA | 53 | |||
| Total output current sourced by sum of all I/Os and control pins | ΣIIO(PIN) | -80 | mA | 53 | |||
| Total output current sourced by sum of all I/Os supplied by VDDIO2 | ΣIIO(PIN) | -40 | mA | 53 | |||
| Injected current on FT and FTf pins | IINJ(PIN) | -5 | 0 | mA | 53 | ||
| Injected current on TC and RST pin | IINJ(PIN) | -5 | 5 | mA | 53 | ||
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | 25 | mA | 53 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 53 | ||
| Maximum junction temperature | TJ | 150 | °C | 53 | |||
| Internal AHB clock frequency | fHCLK | 0 | 48 | MHz | 54 | ||
| Standard operating voltage | VDD | 2 | 3.6 | V | 54 | ||
| I/O supply voltage | VDDIO2 | 1.65 | 3.6 | V | Must not be supplied if VDD is not present | 54 | |
| Analog operating voltage (ADC and DAC not used) | VDDA | 3.6 | V | Must have a potential equal to or higher than VDD | 54 | ||
| Analog operating voltage (ADC and DAC used) | VDDA | 2.4 | 3.6 | V | ADC and DAC used | 54 | |
| Backup operating voltage | VBAT | 1.65 | 3.6 | V | 54 | ||
| I/O input voltage on TC and RST I/O | VIN | -0.3 | V | Printed max VDDIOx+0.3 (not numeric) | 54 | ||
| I/O input voltage on TTa I/O | VIN | -0.3 | V | Printed max VDDA+0.3 (not numeric) | 54 | ||
| I/O input voltage on FT and FTf I/O | VIN | -0.3 | 5.5 | V | 54 | ||
| Power dissipation LQFP48 at TA = 85 °C | PD | 370 | mW | TA = 85 °C for suffix 6 | 54 | ||
| Ambient temperature suffix 6, maximum power dissipation | TA | -40 | 85 | °C | Suffix 6 version, maximum power dissipation | 54 | |
| Ambient temperature suffix 6, low power dissipation | TA | -40 | 105 | °C | Suffix 6 version, low power dissipation | 54 | |
| Junction temperature range suffix 6 | TJ | -40 | 105 | °C | Suffix 6 version | 54 | |
| Power-on/power-down reset threshold, falling edge | VPOR/PDR | 1.8 | 1.88 | 1.96 | V | Falling edge | 55 |
| Power-on/power-down reset threshold, rising edge | VPOR/PDR | 1.84 | 1.92 | 2 | V | Rising edge | 55 |
| PDR hysteresis | VPDRhyst | 40 | mV | 55 | |||
| Reset temporization | tRSTTEMPO | 1.5 | 2.5 | 4.5 | ms | Guaranteed by design, not tested in production | 55 |
| PVD threshold 0 rising edge | VPVD0 | 2.1 | 2.18 | 2.26 | V | Rising edge | 55 |
| PVD threshold 0 falling edge | VPVD0 | 2 | 2.08 | 2.16 | V | Falling edge | 55 |
| PVD threshold 7 rising edge | VPVD7 | 2.76 | 2.88 | 3 | V | Rising edge | 55 |
| PVD threshold 7 falling edge | VPVD7 | 2.66 | 2.78 | 2.9 | V | Falling edge | 55 |
| PVD hysteresis | VPVDhyst | 100 | mV | Guaranteed by design, not tested in production | 55 | ||
| Internal reference voltage | VREFINT | 1.2 | 1.23 | 1.25 | V | -40 °C < TA < +105 °C | 56 |
| Internal reference voltage spread over the temperature range | ∆VREFINT | 10 | mV | VDDA = 3 V | 56 | ||
| Temperature coefficient | TCoeff | -100 | 100 | ppm/°C | Guaranteed by design, not tested in production | 56 | |
| Supply current in Run mode, code executing from Flash, HSI48, all peripherals enabled | IDD | 26.9 | 30.3 | mA | VDD = 3.6 V, 48 MHz; max at TA = 85 °C | 58 | |
| Supply current in Run mode, code executing from Flash, HSI48, all peripherals disabled | IDD | 14.7 | 16.3 | mA | VDD = 3.6 V, 48 MHz; max at TA = 85 °C | 58 | |
| Supply current in Sleep mode, HSI48, all peripherals enabled | IDD | 17 | 19.1 | mA | VDD = 3.6 V, 48 MHz; max at TA = 85 °C | 58 | |
| Supply current in Stop mode, regulator in run mode, all oscillators OFF | IDD | 15.8 | 51 | µA | VDD = 3.6 V; max at TA = 85 °C | 60 | |
| Supply current in Standby mode, LSI OFF and IWDG OFF | IDD | 1.1 | 2.3 | µA | VDD = 3.6 V; max at TA = 85 °C | 60 | |
| HSI oscillator accuracy (factory calibrated) | ACCHSI | -2.8 | 3.8 | % | TA = -40 to 105 °C (data from characterization, not tested in production) | 72 | |
| HSE oscillator frequency | fOSC_IN | 4 | 8 | 32 | MHz | 69 | |
| PLL multiplier output clock | fPLL_OUT | 16 | 48 | MHz | 75 | ||
| 16-bit programming time | tprog | 40 | 53.5 | 60 | µs | TA = -40 to +105 °C | 75 |
CAD (KiCad official)
- Symbol:
STM32F091CCT6 - Footprint:
Package_QFP:LQFP-48_7x7mm_P0.5mm - 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
stm32f091cct6-etched.step/stm32f091cct6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32f091cct6.step/stm32f091cct6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (128 pp, sha256
f96a82f50344c619, retrieved 2026-11-10, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).