Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

RAA214023GNP#HCA

RENESAS · Linear Voltage Regulators (LDO) · QFN-20(3.5x3.5)

RAA214023GNP#HCA from RENESAS, in a QFN-20(3.5x3.5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VOUT power_out VOUT is an output pin that supplies power to the load and requires a minimum 22µF capacitor from VOUT to GND for stable operation.
2 SNS input SNS is the output voltage sense pin and should be connected to VOUT when the voltage set pins program the output, or left floating when external feedback resistors are used.
3 FB input FB is the voltage feedback pin, internally set to 0.8V (±1.75%) by the bandgap, and the divider on this pin sets the output voltage.
4 PG output PG is an open-drain power-good output that is open when VOUT is within 90% and 110% of target and pulls low on a fault, and it should use a 10kΩ to 100kΩ pull-up if used.
5 50mV input 50mV is a voltage set pin that adds 50mV to the output when grounded and may be grounded or left floating.
6 100mV input 100mV is a voltage set pin that adds 100mV to the output when grounded and may be grounded or left floating.
7 200mV input 200mV is a voltage set pin that adds 200mV to the output when grounded and may be grounded or left floating.
8 GND power_in GND is the ground pin that must be tied to ground and connected to the exposed pad.
9 400mV input 400mV is a voltage set pin that adds 400mV to the output when grounded and may be grounded or left floating.
10 800mV input 800mV is a voltage set pin that adds 800mV to the output when grounded and may be grounded or left floating.
11 1.6V input 1.6V is a voltage set pin that adds 1.6V to the output when grounded and may be grounded or left floating.
12 NC unconnected NC is a no-connection pin that must be left floating.
13 CSET passive CSET is the noise reduction pin that requires a 1µF capacitor to ground placed close to the device, and larger values increase start-up time.
14 EN input EN is the enable pin, where low disables the LDO and high enables it, and it must not be left floating and should be tied to VIN for automatic enabling.
15 VIN power_in VIN is an input pin that supplies power to the regulator within the 2.7V to 5.5V range and requires a minimum 10µF ceramic bypass capacitor.
16 VIN power_in VIN is an input pin that supplies power to the regulator within the 2.7V to 5.5V range and requires a minimum 10µF ceramic bypass capacitor.
17 VIN power_in VIN is an input pin that supplies power to the regulator within the 2.7V to 5.5V range and requires a minimum 10µF ceramic bypass capacitor.
18 GND power_in GND is the ground pin that must be tied to ground and connected to the exposed pad.
19 VOUT power_out VOUT is an output pin that supplies power to the load and requires a minimum 22µF capacitor from VOUT to GND for stable operation.
20 VOUT power_out VOUT is an output pin that supplies power to the load and requires a minimum 22µF capacitor from VOUT to GND for stable operation.
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer RENESAS
Package QFN-20(3.5x3.5)
Category Power Management
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage VIN 2.7 5.5 V 6
Ambient Temperature TA -40 125 °C 6
Output Voltage VOUT 0.8 V Maximum printed as VIN - VDO 6
Voltage on VIN, VOUT pins 6.5 V 6
Voltage on SNS, FB, PG, voltage-set pins, CSET, EN 6.5 V 6
Maximum Junction Temperature TJ 150 °C 6
Maximum Storage Temperature Range TSTORE -65 150 °C 6
Thermal Resistance junction-to-ambient, 20 Ld 3.5x3.5 QFN θJA 46 °C/W Free air, high-effective thermal conductivity test board 6
Thermal Resistance junction-to-case, 20 Ld 3.5x3.5 QFN θJC 8 °C/W Center of exposed metal pad 6
Input Voltage Range VIN 2.7 5.5 V 7
Input Supply UVLO VIN_UVLO 2.2 2.3 2.45 V VIN UVLO rising 7
Input Supply UVLO Hysteresis VIN_UVLO_HYS 0.03 0.23 0.3 V VIN UVLO hysteresis 7
Output Current IOUT 2 A 7
VIN Quiescent Current IQ (VIN) 50 195 300 µA VOUT = 3.3V, VIN = 5V 7
Ground Pin Current in Shutdown ISHDN 200 nA VEN = 0V, TJ = +125°C 7
Output Voltage Range VOUT 0.8 V VIN = 2.7V to 5.5V; maximum printed as VIN -VDO 7
FB voltage VFB 0.786 0.8 0.814 V 7
Output Voltage Accuracy, initial -1.5 1.5 % IOUT = 10mA, TJ = 25°C 7
Output Voltage Accuracy, initial -1.75 1.75 % IOUT = 10mA to 2A 7
Line Regulation 0.1 %/V VIN = 2.7V to 5.5V, IOUT = 5mA 7
Load Regulation 0.03 %/A IOUT = 10mA to 2A 7
Dropout Voltage VDO 420 570 mV VIN = 3.3V, IOUT = 2A 7
Internal Current Limit 3.3 A VIN = 2.7V to 5.5V, VOUT = 0V 7
Start-Up Time 200 µs VIN = 5.5V, VOUT = 1.8V, IOUT = 2A, CSET = 1µF 7
Thermal Shutdown Rising 155 °C 7
Thermal Shutdown Hysteresis 10 °C 7

CAD (KiCad official)

  • Symbol: RAA214023GNP#HCA
  • Footprint: Package_DFN_QFN:QFN-20-1EP_3.5x3.5mm_P0.5mm_EP2x2mm
  • 3D model: QFN-20(3.5x3.5) (KiCad packages3D, STEP)
  • 3D model files: raa214023gnp-hca-etched.step / raa214023gnp-hca-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); raa214023gnp-hca.step / raa214023gnp-hca.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: RENESAS datasheet, copy hosted by LCSC (45 pp, sha256 24afeeb3f892c331, retrieved 2026-11-21)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF