Generated by kicad-footprint-generator · KiCad file format 20260206
RAA214023GNP#HCA
RENESAS · Linear Voltage Regulators (LDO) · QFN-20(3.5x3.5)
RAA214023GNP#HCA from RENESAS, in a QFN-20(3.5x3.5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VOUT | power_out | VOUT is an output pin that supplies power to the load and requires a minimum 22µF capacitor from VOUT to GND for stable operation. |
| 2 | SNS | input | SNS is the output voltage sense pin and should be connected to VOUT when the voltage set pins program the output, or left floating when external feedback resistors are used. |
| 3 | FB | input | FB is the voltage feedback pin, internally set to 0.8V (±1.75%) by the bandgap, and the divider on this pin sets the output voltage. |
| 4 | PG | output | PG is an open-drain power-good output that is open when VOUT is within 90% and 110% of target and pulls low on a fault, and it should use a 10kΩ to 100kΩ pull-up if used. |
| 5 | 50mV | input | 50mV is a voltage set pin that adds 50mV to the output when grounded and may be grounded or left floating. |
| 6 | 100mV | input | 100mV is a voltage set pin that adds 100mV to the output when grounded and may be grounded or left floating. |
| 7 | 200mV | input | 200mV is a voltage set pin that adds 200mV to the output when grounded and may be grounded or left floating. |
| 8 | GND | power_in | GND is the ground pin that must be tied to ground and connected to the exposed pad. |
| 9 | 400mV | input | 400mV is a voltage set pin that adds 400mV to the output when grounded and may be grounded or left floating. |
| 10 | 800mV | input | 800mV is a voltage set pin that adds 800mV to the output when grounded and may be grounded or left floating. |
| 11 | 1.6V | input | 1.6V is a voltage set pin that adds 1.6V to the output when grounded and may be grounded or left floating. |
| 12 | NC | unconnected | NC is a no-connection pin that must be left floating. |
| 13 | CSET | passive | CSET is the noise reduction pin that requires a 1µF capacitor to ground placed close to the device, and larger values increase start-up time. |
| 14 | EN | input | EN is the enable pin, where low disables the LDO and high enables it, and it must not be left floating and should be tied to VIN for automatic enabling. |
| 15 | VIN | power_in | VIN is an input pin that supplies power to the regulator within the 2.7V to 5.5V range and requires a minimum 10µF ceramic bypass capacitor. |
| 16 | VIN | power_in | VIN is an input pin that supplies power to the regulator within the 2.7V to 5.5V range and requires a minimum 10µF ceramic bypass capacitor. |
| 17 | VIN | power_in | VIN is an input pin that supplies power to the regulator within the 2.7V to 5.5V range and requires a minimum 10µF ceramic bypass capacitor. |
| 18 | GND | power_in | GND is the ground pin that must be tied to ground and connected to the exposed pad. |
| 19 | VOUT | power_out | VOUT is an output pin that supplies power to the load and requires a minimum 22µF capacitor from VOUT to GND for stable operation. |
| 20 | VOUT | power_out | VOUT is an output pin that supplies power to the load and requires a minimum 22µF capacitor from VOUT to GND for stable operation. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | QFN-20(3.5x3.5) |
| Category | Power Management |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VIN | 2.7 | 5.5 | V | 6 | ||
| Ambient Temperature | TA | -40 | 125 | °C | 6 | ||
| Output Voltage | VOUT | 0.8 | V | Maximum printed as VIN - VDO | 6 | ||
| Voltage on VIN, VOUT pins | 6.5 | V | 6 | ||||
| Voltage on SNS, FB, PG, voltage-set pins, CSET, EN | 6.5 | V | 6 | ||||
| Maximum Junction Temperature | TJ | 150 | °C | 6 | |||
| Maximum Storage Temperature Range | TSTORE | -65 | 150 | °C | 6 | ||
| Thermal Resistance junction-to-ambient, 20 Ld 3.5x3.5 QFN | θJA | 46 | °C/W | Free air, high-effective thermal conductivity test board | 6 | ||
| Thermal Resistance junction-to-case, 20 Ld 3.5x3.5 QFN | θJC | 8 | °C/W | Center of exposed metal pad | 6 | ||
| Input Voltage Range | VIN | 2.7 | 5.5 | V | 7 | ||
| Input Supply UVLO | VIN_UVLO | 2.2 | 2.3 | 2.45 | V | VIN UVLO rising | 7 |
| Input Supply UVLO Hysteresis | VIN_UVLO_HYS | 0.03 | 0.23 | 0.3 | V | VIN UVLO hysteresis | 7 |
| Output Current | IOUT | 2 | A | 7 | |||
| VIN Quiescent Current | IQ (VIN) | 50 | 195 | 300 | µA | VOUT = 3.3V, VIN = 5V | 7 |
| Ground Pin Current in Shutdown | ISHDN | 200 | nA | VEN = 0V, TJ = +125°C | 7 | ||
| Output Voltage Range | VOUT | 0.8 | V | VIN = 2.7V to 5.5V; maximum printed as VIN -VDO | 7 | ||
| FB voltage | VFB | 0.786 | 0.8 | 0.814 | V | 7 | |
| Output Voltage Accuracy, initial | -1.5 | 1.5 | % | IOUT = 10mA, TJ = 25°C | 7 | ||
| Output Voltage Accuracy, initial | -1.75 | 1.75 | % | IOUT = 10mA to 2A | 7 | ||
| Line Regulation | 0.1 | %/V | VIN = 2.7V to 5.5V, IOUT = 5mA | 7 | |||
| Load Regulation | 0.03 | %/A | IOUT = 10mA to 2A | 7 | |||
| Dropout Voltage | VDO | 420 | 570 | mV | VIN = 3.3V, IOUT = 2A | 7 | |
| Internal Current Limit | 3.3 | A | VIN = 2.7V to 5.5V, VOUT = 0V | 7 | |||
| Start-Up Time | 200 | µs | VIN = 5.5V, VOUT = 1.8V, IOUT = 2A, CSET = 1µF | 7 | |||
| Thermal Shutdown Rising | 155 | °C | 7 | ||||
| Thermal Shutdown Hysteresis | 10 | °C | 7 |
CAD (KiCad official)
- Symbol:
RAA214023GNP#HCA - Footprint:
Package_DFN_QFN:QFN-20-1EP_3.5x3.5mm_P0.5mm_EP2x2mm - 3D model: QFN-20(3.5x3.5) (KiCad packages3D, STEP)
- 3D model files:
raa214023gnp-hca-etched.step/raa214023gnp-hca-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);raa214023gnp-hca.step/raa214023gnp-hca.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet, copy hosted by LCSC (45 pp, sha256
24afeeb3f892c331, retrieved 2026-11-21) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).