Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TM2317

TM(Shenzhen Titan Micro Elec) · Audio Interface ICs · QFN-32(5x5)

TM2317 from TM(Shenzhen Titan Micro Elec), in a QFN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 OLINL output Output of the left-channel line-input EQ setting amplifier.
2 LINL input Inverting input of the left-channel line-input EQ setting amplifier.
3 LINSDA input Clock input for production trimming, which can be connected to LINL and driven through a 3.5 mm audio jack.
4 LINSCL input Data input for production trimming, which can be connected to LINR and driven through a 3.5 mm audio jack.
5 LINR input Inverting input of the right-channel line-input EQ setting amplifier.
6 OLINR output Output of the right-channel line-input EQ setting amplifier.
7 MODE_SCL input I²C clock and power-up/power-down/monitor mode control pin; in stand-alone mode MODE must be held high for more than 2 ms to power up, with absolute limits of VNEG-0.5 V to 5 V and recommended control voltage VNEG to 3.7 V.
8 ANC_SDA input I²C serial data and ANC enable pin; it must be pulled high at power-up to enable ANC, and pulling it below 35% VDD with VDD at least 1 V selects play-only mode, with absolute limits of VNEG-0.5 V to 5 V.
9 AGND power_in Analog reference ground, with an absolute maximum rating of -0.5 V to 0.5 V.
10 OMICR output Output of the right-channel ANC microphone gain amplifier.
11 IAMP1R input Inverting input of the right-channel first-stage ANC filter amplifier.
12 OAMP1R output Output of the right-channel first-stage ANC filter amplifier.
13 VNEG power_out Negative charge-pump output with recommended range -1.8 V to -0.7 V; it must be connected to the QFN thermal pad and a 10 µF capacitor is required from this pin to GND.
14 CN input Negative terminal of the negative charge-pump capacitor; a 1 µF capacitor connects CN to CP.
15 GND power_in Ground for the negative charge pump.
16 CP input Positive terminal of the negative charge-pump capacitor; a 1 µF capacitor connects CP to CN.
17 VDD power_in Chip supply input, recommended 1 V to 1.8 V, with an absolute maximum of -0.5 V to 2.0 V.
18 BPL input Left-channel bypass audio signal input.
19 HAMPL output Left-channel headphone driver amplifier output.
20 MIXL input Left-channel mix signal input.
21 MIXR input Right-channel mix signal input.
22 HAMPR output Right-channel headphone driver amplifier output.
23 BPR input Right-channel bypass audio signal input.
24 OAMP1L output Output of the left-channel first-stage ANC filter amplifier.
25 IAMP1L input Inverting input of the left-channel first-stage ANC filter amplifier.
26 OMICL output Output of the left-channel ANC microphone gain amplifier.
27 MICVNL input Inverting-input AC-coupling ground for the left microphone gain amplifier, which requires a 10 µF capacitor to AGND.
28 MICL input Non-inverting input of the left-channel ANC microphone gain amplifier.
29 MICS power_out Microphone supply output, which requires a 10 µF capacitor to AGND.
30 IOUT output LED indicator drive output as an N-channel open-drain output, with a drive sink current of up to 2.2 mA.
31 MICR input Non-inverting input of the right-channel ANC microphone gain amplifier.
32 MICVNR input Inverting-input AC-coupling ground for the right microphone gain amplifier, which requires a 10 µF capacitor to AGND.
33 VNEG power_out Exposed QFN thermal pad, which the datasheet says must be connected to the VNEG pin; the VNEG node also takes a 10 µF capacitor to GND.

Key specifications

Parameter Value
Manufacturer TM(Shenzhen Titan Micro Elec)
Package QFN-32(5x5)
Category Communication Interface Chip/UART/485/232
Pins 33

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Working voltage VDD -0.5 2 V 3
Analog ground AGND AGND -0.5 0.5 V 3
Negative input pin VNEG VNEG -2 0.5 V 3
Control pins MICS, ANC_SDA, MODE_SCL (upper limit; lower limit is VNEG-0.5) 5 V 3
Other pin MICS MICS -0.5 5 V 3
Latch-up suppression current -100 100 mA 3
Continuous power dissipation 200 mW QFN32/40 package 4
Human body model ESD 2 kV HBM 4
Junction temperature 85 ℃ 4
Storage temperature -55 125 ℃ 4
Humidity 5 85 % 4
Reflow soldering temperature 260 ℃ 4
VDD supply voltage VDD 1 1.8 V 正常工作模式 4
VNEG supply voltage VNEG -1.8 -0.7 V 4
Operating temperature Ta -20 85 ℃ 4
Charge pump voltage VVNEG -1.8 -0.7 V 4
Microphone supply voltage VMICS 0 3.7 V MICS 4
Control pin voltage (upper limit; lower limit is VNEG) VCONTROL 3.7 V MODE_SCL, ANC_SDA 4
IOUT drive current IIOUT 2.2 mA IOUT 4
Input voltage of VNEG charge pump VIN 1 1.5 1.8 V VDD 9
SCL, SDA input low level (upper limit) VINL 0.42 V 0.3*VDD(最大) 16
SCL, SDA input high level (lower limit) VINH 0.98 V 0.7*VDD(最小) 16
SCL, SDA input hysteresis HYST 0.2 0.45 0.8 V 16
Response time tSP 50 100 ns 16
High-level SCL pulse width tHW 500 ns 16
Low-level SCL pulse width tLW 500 ns 16
SDA hold time tPD 0 50 ns 16
Start condition hold time tHD:STA 200 ns 16
SDA setup time tSU 250 ns 16

CAD (KiCad official)

  • Symbol: TM2317
  • Footprint: Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm
  • 3D model: QFN-32(5x5), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm tall, datasheet A, midpoint of min and max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: tm2317-etched.step / tm2317-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tm2317.step / tm2317.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: TM(Shenzhen Titan Micro Elec) datasheet (30 pp, sha256 3fafa989a919bf61, retrieved 2026-11-12, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF