3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMIC24066T-E
Microchip Tech · DC-DC Converters · VQFN-36-EP(5x6)
MIC24066T-E from Microchip Tech, in a VQFN-36-EP(5x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | Not connected; leave pin unconnected. |
| 2 | PG | output | Open-drain power good output pulled low when output is below 10% of target; pull up to VDD through 10 kΩ, high when output is above 90% of target. |
| 3 | ILIM | passive | Current limit adjust input; connect a resistor from ILIM to the SW node to set the current limit. |
| 4 | AGND | power_in | Analog ground reference for the control logic; connect AGND to PGND at one point. |
| 5 | SW | power_out | Switch node output; connect all SW pins together and to one terminal of the inductor (also senses low-side MOSFET current for negative current limit). |
| 6 | BST | passive | Bootstrap supply for the high-side MOSFET driver; connect a 0.1 µF low ESR ceramic capacitor between BST and SW. |
| 7 | VIN | power_in | Power supply input to the internal high-side MOSFET; connect all VIN pins together with low ESR ceramic capacitors to PGND close to the IC. |
| 8 | VIN | power_in | Power supply input to the internal high-side MOSFET; connect all VIN pins together with low ESR ceramic capacitors to PGND close to the IC. |
| 9 | VIN | power_in | Power supply input to the internal high-side MOSFET; connect all VIN pins together with low ESR ceramic capacitors to PGND close to the IC. |
| 10 | VIN | power_in | Power supply input to the internal high-side MOSFET; connect all VIN pins together with low ESR ceramic capacitors to PGND close to the IC. |
| 11 | VIN | power_in | Power supply input to the internal high-side MOSFET; connect all VIN pins together with low ESR ceramic capacitors to PGND close to the IC. |
| 12 | VIN | power_in | Power supply input to the internal high-side MOSFET; connect all VIN pins together with low ESR ceramic capacitors to PGND close to the IC. |
| 13 | VIN | power_in | Power supply input to the internal high-side MOSFET; connect all VIN pins together with low ESR ceramic capacitors to PGND close to the IC. |
| 14 | NC | unconnected | Not connected; leave unconnected (datasheet also says it can be floating or grounded). |
| 15 | PGND | power_in | Power ground return for the low-side MOSFET and its driver; connect all PGND pins to the power ground plane. |
| 16 | PGND | power_in | Power ground return for the low-side MOSFET and its driver; connect all PGND pins to the power ground plane. |
| 17 | PGND | power_in | Power ground return for the low-side MOSFET and its driver; connect all PGND pins to the power ground plane. |
| 18 | PGND | power_in | Power ground return for the low-side MOSFET and its driver; connect all PGND pins to the power ground plane. |
| 19 | SW | power_out | Switch node output; connect all SW pins together and to one terminal of the inductor. |
| 20 | SW | power_out | Switch node output; connect all SW pins together and to one terminal of the inductor. |
| 21 | SW | power_out | Switch node output; connect all SW pins together and to one terminal of the inductor. |
| 22 | SW | power_out | Switch node output; connect all SW pins together and to one terminal of the inductor. |
| 23 | NC | unconnected | Not connected; leave unconnected (datasheet also says it can be floating or grounded). |
| 24 | PVDD | power_out | Internal high voltage LDO output supplying the low-side MOSFET driver and bootstrap capacitor; connect a minimum 4.7 µF low ESR ceramic capacitor to PGND. |
| 25 | AGND | power_in | Analog ground reference for the control logic; connect AGND to PGND at one point. |
| 26 | EXTVDD | power_in | Auxiliary LDO input; connect to a supply above 4.7V (typical) to bypass the internal LDO, or leave unconnected/grounded, with a minimum 1 µF capacitor to PGND when supplied. |
| 27 | EN | input | Enable logic input; connect to VIN or an external logic signal, high enables and low disables the device. |
| 28 | NC | unconnected | Not connected; leave pin unconnected. |
| 29 | FREQ | input | Frequency programming input; tie to VIN for 800 kHz or connect to the midpoint of a resistor divider from VIN to AGND to set switching frequency. |
| 30 | SS/MODE | passive | On MIC24066 a capacitor to AGND programs the output soft start time (on MIC24067 this pin selects HLL or CCM light-load mode). |
| 31 | FB | input | Feedback input; connect to the midpoint of a resistor divider from the output to AGND, regulated to 0.6V. |
| 32 | AGND | power_in | Analog ground reference for the control logic; connect AGND to PGND at one point. |
| 33 | AGND | power_in | Analog ground reference for the control logic; connect AGND to PGND at one point. |
| 34 | VDD | power_in | Bias supply for the internal control logic; connect to PVDD through a 2.2Ω series resistor with a minimum 2.2 µF low ESR ceramic capacitor to AGND. |
| 35 | SVIN | power_in | Supply input to the internal LDO; connect to VIN through a 2.2Ω series resistor with a minimum 1 µF low ESR ceramic capacitor to AGND. |
| 36 | NC | unconnected | Not connected; leave pin unconnected. |
| 37 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | VQFN-36-EP(5x6) |
| Category | Power Management |
| Pins | 37 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| PVIN, SVIN Voltage Range | VIN | 4.5 | 36 | V | 6 | ||
| Quiescent Supply Current | IQ | 300 | 600 | µA | VFBS = +1.5V, MODE = GND | 6 | |
| Quiescent Supply Current (no switching) | IQ | 1.4 | 1.8 | mA | VFBS = +1.5V, No Switching | 6 | |
| Shut Down Current | ISD | 5 | 10 | µA | Power from VIN, VEN = 0V | 6 | |
| Shut Down Current (VDD powered) | ISD | 30 | 50 | µA | VIN = VDD = 5.5V, VEN = 0V | 6 | |
| PVDD Output Voltage Range | VDD | 4.8 | 5.1 | 5.4 | V | SVIN = 7V to 36V, IPVDD < = 10 mA | 6 |
| VDD Undervoltage Lockout Upper Threshold | VDDUV_R | 3.7 | 4.2 | 4.5 | V | VDD rising | 6 |
| VDD UVLO Hysteresis | VDDUV_HYS | 600 | mV | Hysteresis | 6 | ||
| VDD Regulation | ΔVDD | 1 | 2.5 | % | VIN = 24V, IVDD from 1 mA to 40 mA (Note 5) | 6 | |
| VDD Regulator Dropout Voltage | VDROP_VDD | 0.7 | 1.25 | V | SVIN = 5.5V, IPVDD = 25 mA | 6 | |
| EXTVDD Switchover Voltage | VSO_EXTVDD | 4.4 | 4.6 | 4.8 | V | EXTVDD rising | 6 |
| EXTVDD Switchover Voltage Hysteresis | VSO_HYS | 200 | mV | Hysteresis | 6 | ||
| EXTVDD Dropout Voltage | VDROP_EXTVDD | 250 | mV | VEXTVDD = 5V, IPVDD = 25 mA | 6 | ||
| EXTVDD Leakage Current | ILK_EXTVDD | 0.1 | µA | VEXTVDD = 14V, VEN = 0V | 6 | ||
| Soft Start Period | tSS | 5 | ms | Fixed internal SS (MIC24067) | 6 | ||
| Soft Start Source Current | ISS | 0.8 | 1.3 | 3 | µA | Programmable SS (MIC24066) | 6 |
| Feedback Regulation Voltage | VFB | 0.597 | 0.6 | 0.603 | V | TJ = 25ºC | 6 |
| Feedback Regulation Voltage (over temperature) | VFB | 0.594 | 0.606 | V | -40ºC ≤ TJ ≤ +125ºC | 6 | |
| FBS Bias Current | IFBS | 50 | 500 | nA | VFBS = +0.6V | 6 | |
| Enable Threshold Voltage High | VEN_THH | 1.6 | V | Enable rising | 6 | ||
| Enable Threshold Voltage Low | VEN_THL | 0.6 | V | Enable falling | 6 | ||
| Enable Hysteresis | VEN_HYS | 150 | mV | 6 | |||
| Enable Bias Current | IEN | 6 | 30 | µA | VEN = 12V | 6 | |
| MODE Threshold Voltage High | VMODE_THH | 1.6 | V | MODE rising | 7 | ||
| MODE Threshold Voltage Low | VMODE_THH | 0.6 | V | MODE falling | 7 | ||
| MODE Hysteresis | VMODE_HYS | 150 | mV | VEN = 12V | 7 | ||
| Maximum Switching Frequency | fSW_max | 720 | 800 | 880 | kHz | VVIN = 12V, VFREQ = VVIN, R5 = 100k Ω; R6 = Open | 7 |
| Minimum Switching Frequency | fSW_MIN | 230 | 270 | 300 | kHz | VIN = 12V, VFREQ = 33% × VVIN, R5 = 100k Ω; R6 = 50k Ω | 7 |
| Maximum Switching Frequency | fSW_max | 800 | kHz | VIN = 12V, VOUTS = 5V | 7 | ||
| Minimum On-Time | TONMIN | 60 | ns | Measured in application | 7 | ||
| Minimum Off-Time | TOFFMIN | 100 | 200 | 300 | ns | VFBS = 0V | 7 |
| Maximum Duty Cycle | DMAX | 85 | % | fSW = 400 kHz, R5 = R6 = 100k Ω | 7 | ||
| Minimum Duty Cycle | DMIN | 0 | % | VFBS = +1V | 7 | ||
| Current-Limit Comparator Offset | VOFFSET | -15 | 0 | 15 | mV | VFB = 0.59V | 7 |
| ILIM Source Current | ICL | 115 | µA | TJ= 25°C | 7 | ||
| ILIM Source Current (over temperature) | ICL | 80 | 180 | µA | TJ= -140°C to 125°C | 7 | |
| ILIM Source Current Tempco | TCICL | 0.3 | µA/°C | 7 | |||
| Negative Current Limit Comparator Threshold | 48 | mV | 7 | ||||
| High Side MOSFET On-Resistance | RDSON_HS | 22 | mΩ | 7 | |||
| Low Side MOSFET On-Resistance | RDSON_LS | 8.5 | mΩ | 7 | |||
| BST Leakage | ILEAK(BST) | 5 | µA | VIN = 45V | 7 | ||
| VIN Leakage | ILEAK(VIN) | 5 | µA | VIN = 45V | 7 | ||
| SW Leakage | ILEAK(SW) | 5 | µA | VIN = 45V | 7 | ||
| PG Threshold from Low to High | VPG_TH | 85 | 90 | 95 | %VREF | VFB rising | 7 |
| PG Threshold Hysteresis | VPG_HYS | 6 | %VREF | VFB falling | 7 | ||
| PG Delay | tD_PG | 100 | µs | VFB rising | 7 | ||
| PG Low State Voltage | VPG_L | 70 | 200 | mV | VFB < 90% × VNOM, IPG = 1 mA | 8 | |
| PG Leakage Current | ILEAK(PG) | 100 | nA | VPG = 5.5V | 8 | ||
| Thermal Shutdown Threshold | TSD | 160 | °C | TJ rising | 8 | ||
| Thermal Shutdown Hysteresis | TSD_HYS | 20 | °C | 8 | |||
| SVIN, PVIN to PGND | -0.3 | 45 | V | 5 | |||
| VDD, PVDD to PGND | -0.3 | 6 | V | 5 | |||
| BST to SW | -0.3 | 12 | V | 5 | |||
| EXTVDD to AGND | -0.3 | 14 | V | 5 | |||
| Maximum Junction Temperature | TJ | 150 | °C | 5 | |||
| Storage Temperature | TS | -65 | 150 | °C | 5 | ||
| Operating Junction Temperature | TJ | -40 | 125 | °C | 5 | ||
| PVDD, VDD Pin Voltage | 4.3 | 5.5 | V | 5 | |||
| Thermal Resistance Junction to Ambient | θJA | 33.7 | °C/W | 8 | |||
| Thermal Resistance Junction to Case (Top) | θJC(Top) | 31.2 | °C/W | 8 |
CAD (KiCad official)
- Symbol:
MIC24066T-E - Footprint:
Package_DFN_QFN:QFN-36-1EP_5x6mm_P0.5mm_EP3.6x4.6mm - 3D model: VQFN-36-EP(5x6) (KiCad packages3D, STEP)
- 3D model files:
mic24066t-e-etched.step/mic24066t-e-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic24066t-e.step/mic24066t-e.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (38 pp, sha256
365d37f2949ec8af, retrieved 2026-10-27, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).