Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

NIS5420MT5TXG

onsemi · Surge Suppressors · WDFN-10(3x3)

NIS5420MT5TXG from onsemi, in a WDFN-10(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND power_in Negative input voltage to the device, used as the internal reference for the IC.
2 dv/dt passive Controls output voltage slew rate at turn-on with an internal capacitor giving about a 2 ms ramp; an external capacitor can be added to lengthen it, and the pin is left open if no extra delay is needed.
3 Enable/Fault bidirectional Tri-state bidirectional pin that shuts down the eFuse when pulled to ground by an open-drain/open-collector device, and indicates status (about 1.4 V = thermal shutdown, about 3 V = normal); do not actively drive it or connect a capacitor.
4 ILimit passive A resistor between this pin and the source pin sets the overload and short circuit current limit levels.
5 NC unconnected No connection on the NIS5420MT5 (this pin is ISENSE only on the MT1, MT2, MT6, MT7 and MT8 variants).
6 Source power_out Source of the internal power FET and output terminal of the fuse, with pins 6-10 all being Source.
7 Source power_out Source of the internal power FET and output terminal of the fuse, with pins 6-10 all being Source.
8 Source power_out Source of the internal power FET and output terminal of the fuse, with pins 6-10 all being Source.
9 Source power_out Source of the internal power FET and output terminal of the fuse, with pins 6-10 all being Source.
10 Source power_out Source of the internal power FET and output terminal of the fuse, with pins 6-10 all being Source.
11 VCC power_in Positive input voltage to the device (belly/exposed pad); operating input range is 8 V to 18 V, with -0.6 to 25 V transient (100 ms).

Key specifications

Parameter Value
Manufacturer onsemi
Package WDFN-10(3x3)
Category TVS/Fuse/Board Level Protection
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Off State Output Voltage Voff 50 mV VCC = 18 Vdc, VGS = 0 Vdc, RL = 4
Continuous Current ID 4.6 A TA = 25°C, 100 mm2 copper (Note 3) 4
Continuous Current ID 3.5 A TA = 80°C, minimum copper 4
Shutdown Temperature TSD 150 175 200 °C Note 3 4
Output Clamping Voltage (NIS5420MT1, NIS5420MT4, NIS5420MT5, NIS5420MT6) VClamp2 13.6 16 V 4
Output Clamping Response Time TClamp_Res 10 s 4
Undervoltage Lockout (NIS5420MT1, NIS5420MT3, NIS5420MT4, NIS5420MT5, NIS5420MT6) VUVLO1 7.8 8.5 9.2 V 4
Kelvin Short Circuit Current Limit ILim−SS 1.76 2.1 2.64 A RLimit = 20, Note 4 4
Logic Level Low (Output Disabled) Vin−low 0.35 0.58 0.81 V 4
Logic Level Mid (Thermal Fault, Output Disabled) Vin−mid 0.82 1.4 1.95 V 4
Logic Level High (Output Enabled) Vin−high 1.96 2.6 3 V 4
High State Maximum Voltage Vin−max 2.51 4.6 5 V 4
Logic Low Sink Current Iin−low -15 -25 A Venable = 0 V 4
Logic High Leakage Current for External Switch Iin−leak 1 A Venable = 3.3 V 4
Maximum Fanout for Fault Signal Fan 3 Units Total number of chips that can be connected to this pin for simultaneous shutdown 4
Bias Current (Operational) IBias 450 A Operational 4
Bias Current (Shutdown) IBias 150 A Shutdown 4
Minimum Operating Voltage Vmin 7.7 V Notes 3 and 5 4
Input Voltage, operating, steady-state VIN -0.6 18 V VCC to GND, Note 1 3
Input Voltage, transient VIN -0.6 25 V 100 ms 3
Operating Ambient Temperature Range TA -40 125 °C 3
Operating Junction Temperature Range TJ -40 150 °C 3
Non-operating Temperature Range TSTG -55 155 °C 3
Lead Temperature, Soldering (10 Sec) TL 260 °C 10 s 3
Total Power Dissipation @ TA = 25°C Pmax 1.39 W 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu 3
Derate above 25°C Pmax 11.1 mW/°C 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu 3
Thermal Resistance, Junction-to-Air θJA 90 °C/W 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu 3
Thermal Characterization Parameter, Junction-to-Lead ΨJ-L 27.5 °C/W 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu 3
Thermal Characterization Parameter, Junction-to-Board ΨJ-B 27.5 °C/W 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu 3
Thermal Characterization Parameter, Junction-to-Case Top ΨJ-T 7.6 °C/W 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu 3
Thermal Hysteresis (Auto-retry part only) THyst 45 °C Auto-retry part only 4
Thermal Shutdown Response Time TSDRes 10 15 20 s 4
UVLO Hysteresis VHyst 0.8 V 4
Kelvin Overload Current Limit ILim−OL 4.2 A RLimit = 20, Note 4 4
Output Voltage Ramp Time tslew 2 ms Enable to VOUT = 11.7 V and 10% to 90%; VOUT = 1.2 V to 10.8 V with 12 Load 4
Delay Time (enabling of chip) Tdly 220 s ID = 100 mA with 1 A resistive load 4

CAD (KiCad official)

  • Symbol: NIS5420MT5TXG
  • Footprint: Package_DFN_QFN:WDFN-10-1EP_3x3mm_P0.5mm_EP1.8x2.5mm
  • 3D model: WDFN-10(3x3) (KiCad packages3D, STEP)

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (13 pp, sha256 fab5291d0e86fefa, retrieved 2026-11-10, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF