3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownNIS5420MT5TXG
onsemi · Surge Suppressors · WDFN-10(3x3)
NIS5420MT5TXG from onsemi, in a WDFN-10(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Negative input voltage to the device, used as the internal reference for the IC. |
| 2 | dv/dt | passive | Controls output voltage slew rate at turn-on with an internal capacitor giving about a 2 ms ramp; an external capacitor can be added to lengthen it, and the pin is left open if no extra delay is needed. |
| 3 | Enable/Fault | bidirectional | Tri-state bidirectional pin that shuts down the eFuse when pulled to ground by an open-drain/open-collector device, and indicates status (about 1.4 V = thermal shutdown, about 3 V = normal); do not actively drive it or connect a capacitor. |
| 4 | ILimit | passive | A resistor between this pin and the source pin sets the overload and short circuit current limit levels. |
| 5 | NC | unconnected | No connection on the NIS5420MT5 (this pin is ISENSE only on the MT1, MT2, MT6, MT7 and MT8 variants). |
| 6 | Source | power_out | Source of the internal power FET and output terminal of the fuse, with pins 6-10 all being Source. |
| 7 | Source | power_out | Source of the internal power FET and output terminal of the fuse, with pins 6-10 all being Source. |
| 8 | Source | power_out | Source of the internal power FET and output terminal of the fuse, with pins 6-10 all being Source. |
| 9 | Source | power_out | Source of the internal power FET and output terminal of the fuse, with pins 6-10 all being Source. |
| 10 | Source | power_out | Source of the internal power FET and output terminal of the fuse, with pins 6-10 all being Source. |
| 11 | VCC | power_in | Positive input voltage to the device (belly/exposed pad); operating input range is 8 V to 18 V, with -0.6 to 25 V transient (100 ms). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | WDFN-10(3x3) |
| Category | TVS/Fuse/Board Level Protection |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Off State Output Voltage | Voff | 50 | mV | VCC = 18 Vdc, VGS = 0 Vdc, RL = | 4 | ||
| Continuous Current | ID | 4.6 | A | TA = 25°C, 100 mm2 copper (Note 3) | 4 | ||
| Continuous Current | ID | 3.5 | A | TA = 80°C, minimum copper | 4 | ||
| Shutdown Temperature | TSD | 150 | 175 | 200 | °C | Note 3 | 4 |
| Output Clamping Voltage (NIS5420MT1, NIS5420MT4, NIS5420MT5, NIS5420MT6) | VClamp2 | 13.6 | 16 | V | 4 | ||
| Output Clamping Response Time | TClamp_Res | 10 | s | 4 | |||
| Undervoltage Lockout (NIS5420MT1, NIS5420MT3, NIS5420MT4, NIS5420MT5, NIS5420MT6) | VUVLO1 | 7.8 | 8.5 | 9.2 | V | 4 | |
| Kelvin Short Circuit Current Limit | ILim−SS | 1.76 | 2.1 | 2.64 | A | RLimit = 20, Note 4 | 4 |
| Logic Level Low (Output Disabled) | Vin−low | 0.35 | 0.58 | 0.81 | V | 4 | |
| Logic Level Mid (Thermal Fault, Output Disabled) | Vin−mid | 0.82 | 1.4 | 1.95 | V | 4 | |
| Logic Level High (Output Enabled) | Vin−high | 1.96 | 2.6 | 3 | V | 4 | |
| High State Maximum Voltage | Vin−max | 2.51 | 4.6 | 5 | V | 4 | |
| Logic Low Sink Current | Iin−low | -15 | -25 | A | Venable = 0 V | 4 | |
| Logic High Leakage Current for External Switch | Iin−leak | 1 | A | Venable = 3.3 V | 4 | ||
| Maximum Fanout for Fault Signal | Fan | 3 | Units | Total number of chips that can be connected to this pin for simultaneous shutdown | 4 | ||
| Bias Current (Operational) | IBias | 450 | A | Operational | 4 | ||
| Bias Current (Shutdown) | IBias | 150 | A | Shutdown | 4 | ||
| Minimum Operating Voltage | Vmin | 7.7 | V | Notes 3 and 5 | 4 | ||
| Input Voltage, operating, steady-state | VIN | -0.6 | 18 | V | VCC to GND, Note 1 | 3 | |
| Input Voltage, transient | VIN | -0.6 | 25 | V | 100 ms | 3 | |
| Operating Ambient Temperature Range | TA | -40 | 125 | °C | 3 | ||
| Operating Junction Temperature Range | TJ | -40 | 150 | °C | 3 | ||
| Non-operating Temperature Range | TSTG | -55 | 155 | °C | 3 | ||
| Lead Temperature, Soldering (10 Sec) | TL | 260 | °C | 10 s | 3 | ||
| Total Power Dissipation @ TA = 25°C | Pmax | 1.39 | W | 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu | 3 | ||
| Derate above 25°C | Pmax | 11.1 | mW/°C | 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu | 3 | ||
| Thermal Resistance, Junction-to-Air | θJA | 90 | °C/W | 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu | 3 | ||
| Thermal Characterization Parameter, Junction-to-Lead | ΨJ-L | 27.5 | °C/W | 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu | 3 | ||
| Thermal Characterization Parameter, Junction-to-Board | ΨJ-B | 27.5 | °C/W | 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu | 3 | ||
| Thermal Characterization Parameter, Junction-to-Case Top | ΨJ-T | 7.6 | °C/W | 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu | 3 | ||
| Thermal Hysteresis (Auto-retry part only) | THyst | 45 | °C | Auto-retry part only | 4 | ||
| Thermal Shutdown Response Time | TSDRes | 10 | 15 | 20 | s | 4 | |
| UVLO Hysteresis | VHyst | 0.8 | V | 4 | |||
| Kelvin Overload Current Limit | ILim−OL | 4.2 | A | RLimit = 20, Note 4 | 4 | ||
| Output Voltage Ramp Time | tslew | 2 | ms | Enable to VOUT = 11.7 V and 10% to 90%; VOUT = 1.2 V to 10.8 V with 12 Load | 4 | ||
| Delay Time (enabling of chip) | Tdly | 220 | s | ID = 100 mA with 1 A resistive load | 4 |
CAD (KiCad official)
- Symbol:
NIS5420MT5TXG - Footprint:
Package_DFN_QFN:WDFN-10-1EP_3x3mm_P0.5mm_EP1.8x2.5mm - 3D model: WDFN-10(3x3) (KiCad packages3D, STEP)
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (13 pp, sha256
fab5291d0e86fefa, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).