3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMP3324GRE-Z
Monolithic Power Systems · LED Drivers · QFN-24(4x4)
MP3324GRE-Z from Monolithic Power Systems, in a QFN-24(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RFSH/FLT | bidirectional | Refresh signal output or fault flag; active-low open drain that outputs the FRFSH[9:0] synchronized signal when FLTEN=0 and is pulled low on a fault when FLTEN=1, requiring an external pull-up. |
| 2 | EN | input | Enable control; pull high to turn the LED driver on and low to turn it off. |
| 3 | SCL | input | I2C interface clock input. |
| 4 | SDA | bidirectional | I2C interface data pin. |
| 5 | ADDR | input | I2C address setting; a resistor between ADDR and GND sets the 4 LSB of the I2C address, with 10 configurable addresses. |
| 6 | ISET | passive | LED current setting; connect a current-setting resistor between ISET and GND to configure the current in each LED string. |
| 7 | LED1 | passive | LED channel 1 current input; connect the channel 1 cathode to this pin, and both LED1 pins (7, 8) to the cathode. |
| 8 | LED1 | passive | LED channel 1 current input; connect the channel 1 cathode to this pin, and both LED1 pins (7, 8) to the cathode. |
| 9 | LED2 | passive | LED channel 2 current input; connect the channel 2 cathode to this pin, and both LED2 pins (9, 10) to the cathode. |
| 10 | LED2 | passive | LED channel 2 current input; connect the channel 2 cathode to this pin, and both LED2 pins (9, 10) to the cathode. |
| 11 | LED3 | passive | LED channel 3 current input; connect the channel 3 cathode to this pin, and both LED3 pins (11, 12) to the cathode. |
| 12 | LED3 | passive | LED channel 3 current input; connect the channel 3 cathode to this pin, and both LED3 pins (11, 12) to the cathode. |
| 13 | LED4 | passive | LED channel 4 current input; connect the channel 4 cathode to this pin, and both LED4 pins (13, 15) to the cathode. |
| 14 | GND | power_in | Ground. |
| 15 | LED4 | passive | LED channel 4 current input; connect the channel 4 cathode to this pin, and both LED4 pins (13, 15) to the cathode. |
| 16 | LED5 | passive | LED channel 5 current input; connect the channel 5 cathode to this pin, and both LED5 pins (16, 17) to the cathode. |
| 17 | LED5 | passive | LED channel 5 current input; connect the channel 5 cathode to this pin, and both LED5 pins (16, 17) to the cathode. |
| 18 | LED6 | passive | LED channel 6 current input; connect the channel 6 cathode to this pin, and both LED6 pins (18, 19) to the cathode. |
| 19 | LED6 | passive | LED channel 6 current input; connect the channel 6 cathode to this pin, and both LED6 pins (18, 19) to the cathode. |
| 20 | LED7 | passive | LED channel 7 current input; connect the channel 7 cathode to this pin, and both LED7 pins (20, 21) to the cathode. |
| 21 | LED7 | passive | LED channel 7 current input; connect the channel 7 cathode to this pin, and both LED7 pins (20, 21) to the cathode. |
| 22 | LED8 | passive | LED channel 8 current input; connect the channel 8 cathode to this pin, and both LED8 pins (22, 23) to the cathode. |
| 23 | LED8 | passive | LED channel 8 current input; connect the channel 8 cathode to this pin, and both LED8 pins (22, 23) to the cathode. |
| 24 | VIN | power_in | Power supply input for the IC, operating from 4V to 16V (absolute max 18V); connect a capacitor between VIN and GND. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-24(4x4) |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage | VIN | 4 | 16 | V | 6 | ||
| Quiescent current | IQ | 4 | mA | 6 | |||
| Shutdown current | ISD | 2 | μA | VEN = 0V, VIN = 16V | 6 | ||
| VIN UVLO rising threshold | VIN_UVLO_RISING | 3.45 | 3.7 | 3.95 | V | Rising edge | 6 |
| VIN UVLO falling threshold | VIN_UVLO_FALLING | 3.15 | 3.5 | 3.85 | V | Falling edge | 6 |
| EN rising threshold | VEN_RISING | 2.1 | V | VEN rising | 6 | ||
| EN falling threshold | VEN_FALLING | 0.8 | V | VEN falling | 6 | ||
| EN pull-down resistance | REN | 1 | MΩ | 6 | |||
| Refresh signal frequency | fREFRESH | 285 | 300 | 315 | Hz | FRFSH[9:0] = 0x1A9, FPWM[2:0] = 01 | 6 |
| RFSH/FLT pull-down resistance | RRFSH/FLT | 100 | Ω | FLTEN = 1, a fault has occurred | 6 | ||
| ISET voltage | VISET | 1.174 | 1.2 | 1.226 | V | TA = 25°C | 6 |
| LED current | ILED | -2 | 50 | 2 | mA | RISET = 20kΩ, ICHx[5:0] = 0x3F, TA = 25°C; tolerance in % | 6 |
| Current sink headroom | VLEDx | 150 | 210 | mV | ILED = 40mA | 6 | |
| PWM frequency | fPWM | 230 | 245 | 260 | Hz | FPWM[1:0] = 01 | 6 |
| PWM duty step | tPWM | 0.97 | μs | 12-bit resolution, fPWM = 250Hz | 6 | ||
| Phase shift | tDELAY | 80 | μs | PS_EN = 1 | 6 | ||
| LED current step | 0.8 | mA | ILED = 50mA, analog dimming step | 6 | |||
| LED current slew rate during PWM dimming | 5 | μs | SLEW[1:0] = 01, rising edge | 6 | |||
| LED current slew rate during PWM dimming | 20 | μs | SLEW[1:0] = 11, rising edge | 6 | |||
| LED string SLP threshold | VSLP | 2.75 | 3 | 3.25 | V | STH[1:0] = 01 | 6 |
| LED string SLP time | tSLP | 4 | ms | VLEDx > STH[1:0] | 6 | ||
| LED string SLP hiccup time | tSLP_HICCUP | 1 | ms | 6 | |||
| LED string SLP hiccup detection time | tSLP_DET | 32 | μs | 6 | |||
| LED string OLP threshold | VOLP | 100 | 160 | mV | 6 | ||
| LED string OLP time | tOLP | 4 | ms | VLEDx < 100mV | 6 | ||
| LED string OLP hiccup time | tOLP_HICCUP | 1 | ms | 6 | |||
| LED string OLP hiccup detection time | tOLP_DET | 32 | μs | 6 | |||
| Thermal shutdown threshold | TSD | 170 | °C | Guaranteed by characterization | 7 | ||
| Thermal shutdown hysteresis | TSD_HYS | 20 | °C | Guaranteed by characterization | 7 | ||
| Input logic low voltage | VIN_LOW | 0 | 0.4 | V | I2C | 7 | |
| Input logic high voltage | VIN_HIGH | 1.3 | V | I2C | 7 | ||
| Output logic low voltage | VOUT_LOW | 0.4 | V | ILOAD = 3mA | 7 | ||
| SCL clock frequency | fSCL | 10 | 1000 | kHz | 7 | ||
| Bus free time | tBUS_FREE | 0.5 | μs | Between stop and start conditions | 7 | ||
| Holding time after start/repeated start condition | tHOLD_START | 0.26 | μs | The first clock is generated after this period | 7 | ||
| Repeated start condition set-up time | tSU_START | 0.26 | μs | 7 | |||
| Stop condition set-up time | tSU_STOP | 0.26 | μs | 7 | |||
| Data hold time | tHOLD_DATA | 0 | ns | 7 | |||
| Data set-up time | tSU_DATA | 50 | ns | 7 | |||
| Clock low timeout | tTIMEOUT | 25 | 35 | ms | 7 | ||
| Clock low time | tLOW | 0.5 | μs | 7 | |||
| Clock high time | tHIGH | 0.26 | μs | 7 | |||
| Clock/data fall time | tFALL | 120 | ns | 7 | |||
| Clock/data rise time | tRISE | 120 | ns | 7 | |||
| VIN absolute maximum | VIN | -0.3 | 18 | V | 5 | ||
| LED1 to LED8 voltage | VLED1 to VLED8 | -0.5 | 18 | V | 5 | ||
| All other pins | -0.3 | 5 | V | 5 | |||
| Junction temperature | TJ | 150 | °C | 5 | |||
| Lead temperature | 260 | °C | 5 | ||||
| Storage temperature | -65 | 150 | °C | 5 | |||
| Continuous power dissipation | 2.97 | W | TA = 25°C, QFN-24 (4mmx4mm) | 5 | |||
| ESD HBM | -2 | 2 | kV | Human body model | 5 | ||
| ESD CDM | -750 | 750 | V | Charged device model | 5 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 5 | ||
| Thermal resistance junction-case | θJC | 9 | °C/W | QFN-24 (4mmx4mm), JESD51-7 4-layer PCB | 5 |
CAD (KiCad official)
- Symbol:
MP3324GRE-Z - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: QFN-24(4x4) (KiCad packages3D, STEP)
- 3D model files:
mp3324gre-z-etched.step/mp3324gre-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mp3324gre-z.step/mp3324gre-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (29 pp, sha256
a5ddb2b1edda4788, retrieved 2026-10-27, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).