Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TPS562206DRLR

Texas Instruments · DC-DC Converters · SOT-563

TPS562206DRLR from Texas Instruments, in a SOT-563. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Input voltage supply pin; the recommended input range is 4.2 V to 17 V and the absolute maximum is 18 V.
2 SW output Switch node connection between the high-side NFET and the low-side NFET; recommended range is -1 V to 17 V, with -6 V to 19 V for transients under 20 ns.
3 GND power_in Ground pin, the source terminal of the low-side power NFET and the ground for the controller circuit; connect sensitive FB to this GND at a single point.
4 BST output Supply input for the high-side NFET gate drive circuit; connect a 0.1 µF capacitor between BST and SW, with a recommended BST voltage of -0.1 V to 23 V.
5 EN input Active-high enable input that must be pulled up to enable the device; recommended range is -0.1 V to 5.5 V.
6 FB input Converter feedback input; connect to the output voltage through a feedback resistor divider; recommended range is -0.1 V to 5.5 V.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SOT-563
Category Power Management (PMIC)
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage range VIN 4.2 17 V 4
Input voltage FB, EN FB, EN -0.1 5.5 V 4
GND GND -0.1 0.1 V 4
Output voltage BST BST -0.1 23 V 4
Output voltage BST (< 20ns) BST -0.1 25 V < 20ns 4
Output voltage SW SW -1 17 V 4
Output voltage SW (< 20ns) SW -6 19 V < 20ns 4
Output current IO 0 2 A 4
Operating junction temperature TJ -40 125 °C 4
Storage temperature Tstg -40 150 °C 4
Input voltage VIN VIN -0.3 18 V 4
Input voltage FB, EN FB, EN -0.3 6 V 4
Input voltage GND GND -0.3 0.3 V 4
Output voltage BST BST -0.3 25 V 4
Output voltage BST (< 20ns) BST -0.3 27 V < 20ns 4
Output voltage SW SW -2 18 V 4
Output voltage SW (< 20ns) SW -6.5 20 V < 20ns 4
Operating junction temperature range TJ -40 150 °C 4
Storage temperature Tstg -55 150 °C 4
Input voltage range Vin 4.2 17 V 5
Vin undervoltage lockout wake-up voltage UVLO 3.6 3.8 4 V 5
Vin undervoltage lockout shut-down voltage UVLO 3.2 3.4 3.6 V 5
FB voltage VFB 591 600 609 mV TJ = 25°C, Vin = 4.2, 17V 5
FB voltage VFB 588 600 612 mV TJ = -40°C to 125°C, Vin = 4.2, 17V 5
Over current threshold IOCL_LS 2.5 3.9 4.8 A Valley current set point 5
Negative over current threshold INOCL 0.7 1.3 1.9 A Valley current set point 5
EN threshold high-level VEN(On) 1.15 1.21 1.27 V 5
EN threshold low-level VEN(Off) 0.95 1 1.05 V 5
UVP trip threshold VUVP 55 60 65 % 6
Vin supply current (FCCM version) IVin 350 µA No load, VEN = 5V, VFB = 0.7V, FCCM version 5
Vin shutdown current IInSdn 7 µA VEN = 0V 5
Minimum off-time TOFF(Min) 100 ns VFB = 0.5V 5
Minimum on-time TON(Min) 55 ns 5
UVLO hysteresis UVLO 400 mV 5
High-side MOSFET Rds(on) RDS(on)Hi 100 mΩ TJ = 25°C 5
Low-side MOSFET Rds(on) RDS(on)Lo 55 mΩ TJ = 25°C 5
Switching frequency FSW 600 kHz VVOUT = 3.3V 5
EN hysteresis VENHys 200 mV 5
EN pulldown current IEN 1 uA VEN = 1.5V 5
Internal soft-start time tSS 1.4 ms Vout from 0 to target value. 6
UVP prop deglitch tUVPDly 256 us 6
Hiccup switching time tUVPOn 1.5 ms In continuous hiccup mode, the switching time; Hard short, UVP detect 6
Hiccup non-switching time tUVPOff 13 ms In continuous hiccup mode, non-switching time; Hard short, UVP detect 6
OTP trip threshold TOTP 155 °C 6
OTP hysteresis TOTPHsy 20 °C 6
Junction-to-ambient thermal resistance RθJA 147.4 °C/W 5
Junction-to-ambient thermal resistance on EVM board RθJA_effective 73 °C/W TPS562203EVM board (2-layer, 2oz copper), Vin = 12V, Vout = 5V, Iout = 2A, TA = 25°C 5
Junction-to-case (top) thermal resistance RθJC(top) 75.7 °C/W 5
Junction-to-board thermal resistance RθJB 32.2 °C/W 5
Junction-to-top characterization parameter ΨJT 2.1 °C/W 5
Junction-to-board characterization parameter ΨJB 31.8 °C/W 5

CAD (KiCad official)

  • Symbol: TPS562206DRLR
  • Footprint: Package_TO_SOT_SMD:SOT-563
  • 3D model: SOT-563 (KiCad packages3D, STEP)
  • 3D model files: tps562206drlr-etched.step / tps562206drlr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps562206drlr.step / tps562206drlr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (31 pp, sha256 5386be9591301747, retrieved 2026-11-07, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF