3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTPS562206DRLR
Texas Instruments · DC-DC Converters · SOT-563
TPS562206DRLR from Texas Instruments, in a SOT-563. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Input voltage supply pin; the recommended input range is 4.2 V to 17 V and the absolute maximum is 18 V. |
| 2 | SW | output | Switch node connection between the high-side NFET and the low-side NFET; recommended range is -1 V to 17 V, with -6 V to 19 V for transients under 20 ns. |
| 3 | GND | power_in | Ground pin, the source terminal of the low-side power NFET and the ground for the controller circuit; connect sensitive FB to this GND at a single point. |
| 4 | BST | output | Supply input for the high-side NFET gate drive circuit; connect a 0.1 µF capacitor between BST and SW, with a recommended BST voltage of -0.1 V to 23 V. |
| 5 | EN | input | Active-high enable input that must be pulled up to enable the device; recommended range is -0.1 V to 5.5 V. |
| 6 | FB | input | Converter feedback input; connect to the output voltage through a feedback resistor divider; recommended range is -0.1 V to 5.5 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOT-563 |
| Category | Power Management (PMIC) |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage range | VIN | 4.2 | 17 | V | 4 | ||
| Input voltage FB, EN | FB, EN | -0.1 | 5.5 | V | 4 | ||
| GND | GND | -0.1 | 0.1 | V | 4 | ||
| Output voltage BST | BST | -0.1 | 23 | V | 4 | ||
| Output voltage BST (< 20ns) | BST | -0.1 | 25 | V | < 20ns | 4 | |
| Output voltage SW | SW | -1 | 17 | V | 4 | ||
| Output voltage SW (< 20ns) | SW | -6 | 19 | V | < 20ns | 4 | |
| Output current | IO | 0 | 2 | A | 4 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Storage temperature | Tstg | -40 | 150 | °C | 4 | ||
| Input voltage VIN | VIN | -0.3 | 18 | V | 4 | ||
| Input voltage FB, EN | FB, EN | -0.3 | 6 | V | 4 | ||
| Input voltage GND | GND | -0.3 | 0.3 | V | 4 | ||
| Output voltage BST | BST | -0.3 | 25 | V | 4 | ||
| Output voltage BST (< 20ns) | BST | -0.3 | 27 | V | < 20ns | 4 | |
| Output voltage SW | SW | -2 | 18 | V | 4 | ||
| Output voltage SW (< 20ns) | SW | -6.5 | 20 | V | < 20ns | 4 | |
| Operating junction temperature range | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -55 | 150 | °C | 4 | ||
| Input voltage range | Vin | 4.2 | 17 | V | 5 | ||
| Vin undervoltage lockout wake-up voltage | UVLO | 3.6 | 3.8 | 4 | V | 5 | |
| Vin undervoltage lockout shut-down voltage | UVLO | 3.2 | 3.4 | 3.6 | V | 5 | |
| FB voltage | VFB | 591 | 600 | 609 | mV | TJ = 25°C, Vin = 4.2, 17V | 5 |
| FB voltage | VFB | 588 | 600 | 612 | mV | TJ = -40°C to 125°C, Vin = 4.2, 17V | 5 |
| Over current threshold | IOCL_LS | 2.5 | 3.9 | 4.8 | A | Valley current set point | 5 |
| Negative over current threshold | INOCL | 0.7 | 1.3 | 1.9 | A | Valley current set point | 5 |
| EN threshold high-level | VEN(On) | 1.15 | 1.21 | 1.27 | V | 5 | |
| EN threshold low-level | VEN(Off) | 0.95 | 1 | 1.05 | V | 5 | |
| UVP trip threshold | VUVP | 55 | 60 | 65 | % | 6 | |
| Vin supply current (FCCM version) | IVin | 350 | µA | No load, VEN = 5V, VFB = 0.7V, FCCM version | 5 | ||
| Vin shutdown current | IInSdn | 7 | µA | VEN = 0V | 5 | ||
| Minimum off-time | TOFF(Min) | 100 | ns | VFB = 0.5V | 5 | ||
| Minimum on-time | TON(Min) | 55 | ns | 5 | |||
| UVLO hysteresis | UVLO | 400 | mV | 5 | |||
| High-side MOSFET Rds(on) | RDS(on)Hi | 100 | mΩ | TJ = 25°C | 5 | ||
| Low-side MOSFET Rds(on) | RDS(on)Lo | 55 | mΩ | TJ = 25°C | 5 | ||
| Switching frequency | FSW | 600 | kHz | VVOUT = 3.3V | 5 | ||
| EN hysteresis | VENHys | 200 | mV | 5 | |||
| EN pulldown current | IEN | 1 | uA | VEN = 1.5V | 5 | ||
| Internal soft-start time | tSS | 1.4 | ms | Vout from 0 to target value. | 6 | ||
| UVP prop deglitch | tUVPDly | 256 | us | 6 | |||
| Hiccup switching time | tUVPOn | 1.5 | ms | In continuous hiccup mode, the switching time; Hard short, UVP detect | 6 | ||
| Hiccup non-switching time | tUVPOff | 13 | ms | In continuous hiccup mode, non-switching time; Hard short, UVP detect | 6 | ||
| OTP trip threshold | TOTP | 155 | °C | 6 | |||
| OTP hysteresis | TOTPHsy | 20 | °C | 6 | |||
| Junction-to-ambient thermal resistance | RθJA | 147.4 | °C/W | 5 | |||
| Junction-to-ambient thermal resistance on EVM board | RθJA_effective | 73 | °C/W | TPS562203EVM board (2-layer, 2oz copper), Vin = 12V, Vout = 5V, Iout = 2A, TA = 25°C | 5 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 75.7 | °C/W | 5 | |||
| Junction-to-board thermal resistance | RθJB | 32.2 | °C/W | 5 | |||
| Junction-to-top characterization parameter | ΨJT | 2.1 | °C/W | 5 | |||
| Junction-to-board characterization parameter | ΨJB | 31.8 | °C/W | 5 |
CAD (KiCad official)
- Symbol:
TPS562206DRLR - Footprint:
Package_TO_SOT_SMD:SOT-563 - 3D model: SOT-563 (KiCad packages3D, STEP)
- 3D model files:
tps562206drlr-etched.step/tps562206drlr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps562206drlr.step/tps562206drlr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (31 pp, sha256
5386be9591301747, retrieved 2026-11-07, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).