3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLTM8001IY#PBF
Analog Devices · DC-DC Converters · BGA-121
LTM8001IY#PBF from Analog Devices, in a BGA-121. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| A1 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| B1 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| C1 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| D1 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| E1 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| F1 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| G1 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| H1 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| J1 | VIN0 | power_in | Supplies the internal regulator and power switches; must be locally bypassed with a low ESR capacitor. |
| K1 | VIN0 | power_in | Supplies the internal regulator and power switches; must be locally bypassed with a low ESR capacitor. |
| L1 | VIN0 | power_in | Supplies the internal regulator and power switches; must be locally bypassed with a low ESR capacitor. |
| A2 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| B2 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| C2 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| D2 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| E2 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| F2 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| G2 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| H2 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| J2 | VIN0 | power_in | Supplies the internal regulator and power switches; must be locally bypassed with a low ESR capacitor. |
| K2 | VIN0 | power_in | Supplies the internal regulator and power switches; must be locally bypassed with a low ESR capacitor. |
| L2 | VIN0 | power_in | Supplies the internal regulator and power switches; must be locally bypassed with a low ESR capacitor. |
| A3 | VOUT0 | power_out | Switching converter output; apply the output filter capacitor and load between these pins and GND. |
| B3 | VOUT0 | power_out | Switching converter output; apply the output filter capacitor and load between these pins and GND. |
| C3 | VOUT0 | power_out | Switching converter output; apply the output filter capacitor and load between these pins and GND. |
| D3 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| E3 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| F3 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| G3 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| H3 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| J3 | VIN0 | power_in | Supplies the internal regulator and power switches; must be locally bypassed with a low ESR capacitor. |
| K3 | VIN0 | power_in | Supplies the internal regulator and power switches; must be locally bypassed with a low ESR capacitor. |
| L3 | VIN0 | power_in | Supplies the internal regulator and power switches; must be locally bypassed with a low ESR capacitor. |
| A4 | VOUT0 | power_out | Switching converter output; apply the output filter capacitor and load between these pins and GND. |
| B4 | VOUT0 | power_out | Switching converter output; apply the output filter capacitor and load between these pins and GND. |
| C4 | VOUT0 | power_out | Switching converter output; apply the output filter capacitor and load between these pins and GND. |
| D4 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| E4 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| F4 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| G4 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| H4 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| J4 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| K4 | SS | passive | Soft-start pin; an external capacitor to ground limits regulated current during start-up, charged with an 11μA source. |
| L4 | RUN | input | Enable pin with no internal pull-up or pull-down; internally clamped, may be pulled up through a resistor if pin current does not exceed 100µA. |
| A5 | VOUT0 | power_out | Switching converter output; apply the output filter capacitor and load between these pins and GND. |
| B5 | VOUT0 | power_out | Switching converter output; apply the output filter capacitor and load between these pins and GND. |
| C5 | VOUT0 | power_out | Switching converter output; apply the output filter capacitor and load between these pins and GND. |
| D5 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| E5 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| F5 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| G5 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| H5 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| J5 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| K5 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| L5 | FB0 | input | Regulates the FB0 pin to 1.19V; the feedback resistor RFB0 connects from this pin to ground, with RFB0 in kΩ = 11.9/(VOUT - 1.19). |
| A6 | VIN45 | power_in | Input to the LDOs connected to VOUT4 and VOUT5; must be locally bypassed with a low ESR capacitor. |
| B6 | VIN45 | power_in | Input to the LDOs connected to VOUT4 and VOUT5; must be locally bypassed with a low ESR capacitor. |
| C6 | VIN45 | power_in | Input to the LDOs connected to VOUT4 and VOUT5; must be locally bypassed with a low ESR capacitor. |
| D6 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| E6 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| F6 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| G6 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| H6 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| J6 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| K6 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| L6 | COMP | passive | Internal compensation pin that connects to the PWM comparator input; leave open if not used. |
| A7 | VIN45 | power_in | Input to the LDOs connected to VOUT4 and VOUT5; must be locally bypassed with a low ESR capacitor. |
| B7 | VIN45 | power_in | Input to the LDOs connected to VOUT4 and VOUT5; must be locally bypassed with a low ESR capacitor. |
| C7 | VIN45 | power_in | Input to the LDOs connected to VOUT4 and VOUT5; must be locally bypassed with a low ESR capacitor. |
| D7 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| E7 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| F7 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| G7 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| H7 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| J7 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| K7 | SYNC | input | Frequency synchronization pin; set RT for a switching clock 20% slower than the SYNC pulse, and ground it when unused, never leaving it floating. |
| L7 | RT | passive | Programs the switching frequency through a resistor to ground; must not be left open, and is set 20% lower than the SYNC frequency when SYNC is used. |
| A8 | BIAS45 | power_in | Supply for the control circuitry of the LDOs on VOUT4 and VOUT5; must be 1.2V to 1.6V above the output voltage for regulation. |
| B8 | BIAS123 | power_in | Supply for the control circuitry of the LDOs on VOUT1-VOUT3; must be 1.2V to 1.6V above the output voltage for regulation. |
| C8 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| D8 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| E8 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| F8 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| G8 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| H8 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| J8 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| K8 | VREF | power_out | Buffered 2V reference capable of supplying 0.5mA drive. |
| L8 | ILIM | input | Reduces maximum regulated output current over a 0V to 1.5V control range; voltages above 1.5V have little effect and it should be tied to VREF if unused. |
| A9 | SET5 | passive | Sets the LDO5 regulation point; a fixed 10μA flows out of this pin through a single resistor. |
| B9 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| C9 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| D9 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| E9 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| F9 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| G9 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| H9 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| J9 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| K9 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| L9 | SET1 | passive | Sets the LDO1 regulation point; a fixed 10μA flows out of this pin through a single resistor. |
| A10 | VOUT5 | power_out | Power output of LDO5; must carry at least 1mA minimum load or the output may not regulate. |
| B10 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| C10 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| D10 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| E10 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| F10 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| G10 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| H10 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| J10 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| K10 | GND | power_in | Tie to a local ground plane; most module heat flows out through these pads. |
| L10 | VOUT1 | power_out | Power output of LDO1; must carry at least 1mA minimum load or the output may not regulate. |
| A11 | VOUT5 | power_out | Power output of LDO5; must carry at least 1mA minimum load or the output may not regulate. |
| B11 | VOUT4 | power_out | Power output of LDO4; must carry at least 1mA minimum load or the output may not regulate. |
| C11 | VOUT4 | power_out | Power output of LDO4; must carry at least 1mA minimum load or the output may not regulate. |
| D11 | SET4 | passive | Sets the LDO4 regulation point; a fixed 10μA flows out of this pin through a single resistor. |
| E11 | VOUT3 | power_out | Power output of LDO3; must carry at least 1mA minimum load or the output may not regulate. |
| F11 | VOUT3 | power_out | Power output of LDO3; must carry at least 1mA minimum load or the output may not regulate. |
| G11 | SET3 | passive | Sets the LDO3 regulation point; a fixed 10μA flows out of this pin through a single resistor. |
| H11 | SET2 | passive | Sets the LDO2 regulation point; a fixed 10μA flows out of this pin through a single resistor. |
| J11 | VOUT2 | power_out | Power output of LDO2; must carry at least 1mA minimum load or the output may not regulate. |
| K11 | VOUT2 | power_out | Power output of LDO2; must carry at least 1mA minimum load or the output may not regulate. |
| L11 | VOUT1 | power_out | Power output of LDO1; must carry at least 1mA minimum load or the output may not regulate. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | BGA-121 |
| Category | Power Supply Chip |
| Pins | 121 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage at FB0 Pin | 1.15 | 1.19 | 1.21 | V | 3 | ||
| ILIM Control Range | 0 | 1.5 | V | 3 | |||
| ILIM Current Limit Accuracy | 5.1 | 6.4 | A | ILIM = 1.5V | 3 | ||
| ILIM Current Limit Accuracy | 2.5 | 3.4 | A | ILIM = 0.75V | 3 | ||
| VREF Voltage | 1.9 | 2 | 2.1 | V | 0.5mA Load | 3 | |
| SYNC Input Low Threshold | 0.8 | V | fSYNC = 500kHz | 3 | |||
| SYNC Input High Threshold | 1.2 | V | fSYNC = 500kHz | 3 | |||
| SYNC Input Current | -0.1 | 0.1 | µA | SYNC = 0V, SYNC = 2V | 3 | ||
| VOUT0 Line Regulation | -0.5 | 0.5 | % | 6V < VIN0 < 36V, IOUT = 1A | 3 | ||
| VOUT0 Load Regulation | -1.2 | 1.2 | % | VIN0 = 24V, 0A < IOUT < 5A | 3 | ||
| SET1-5 Pin Current | 9.8 | 10 | 10.2 | µA | BIAS123 = BIAS45 = 2V, SETx = 0V, IOUT1-5 = 1mA | 3 | |
| VOUTx, SETx Offset Voltage | -4 | 4 | mV | BIAS123 = BIAS45 = 2V, SETx = 0V, IOUT1-5 = 1mA | 3 | ||
| VOUTx, SETx Offset Voltage | -6.5 | 6.5 | mV | BIAS123 = BIAS45 = 2V, SETx = 0V, IOUT1-5 = 1mA | 3 | ||
| Minimum VIN0 Input Voltage | 6 | V | 3 | ||||
| VIN0 to VOUT0 Absolute Max Input Voltage | VIN0 | 40 | V | 2 | |||
| VIN45, BIAS45 Absolute Max Voltage | VIN45, BIAS45 | 25 | V | 2 | |||
| BIAS123 Absolute Max Voltage | BIAS123 | 25 | V | 2 | |||
| FB0, RT, COMP, ILIM, VREF Absolute Max Voltage | 3 | V | 2 | ||||
| VOUT0-5 Absolute Max Voltage | VOUT0-5 | 25 | V | 2 | |||
| RUN, SYNC, SS Absolute Max Voltage | 6 | V | 2 | ||||
| SET1-5 Voltage Relative to VOUT1-5 | SET1-5 | -0.3 | 0.3 | V | Relative to VOUT1-5, respectively | 2 | |
| Current Into SET1-5 | -10 | 10 | mA | 2 | |||
| Current Into RUN Pin | 100 | µA | 2 | ||||
| Maximum Junction Temperature | TJMAX | 125 | °C | Notes 2, 3 | 2 | ||
| Peak Solder Reflow Body Temperature | 245 | °C | 2 | ||||
| Storage Temperature | -55 | 125 | °C | Note 1 | 2 | ||
| Operating Temperature Range (I grade) | -40 | 125 | °C | Internal operating temperature, LTM8001IY#PBF | 2 | ||
| Junction-to-Ambient Thermal Resistance | θJA | 16.1 | °C/W | JESD 51-9, 51-12 | 2 | ||
| Junction-to-Bottom Case Thermal Resistance | θJCbottom | 5.99 | °C/W | JESD 51-9, 51-12 | 2 | ||
| Junction-to-Top Case Thermal Resistance | θJCtop | 13.4 | °C/W | JESD 51-9, 51-12 | 2 | ||
| Junction-to-Board Thermal Resistance | θJB | 4.98 | °C/W | JESD 51-9, 51-12 | 2 |
CAD (KiCad official)
- Symbol:
LTM8001IY#PBF - Footprint:
Package_BGA:BGA-121_9.0x9.0mm_Layout11x11_P0.8mm_Ball0.4mm_Pad0.35mm_NSMD - 3D model: BGA-121 (KiCad packages3D, STEP)
- 3D model files:
ltm8001iy-pbf-etched.step/ltm8001iy-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltm8001iy-pbf.step/ltm8001iy-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (28 pp, sha256
772b849c19b80ff3, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).