3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLM193QT
STMicroelectronics · Comparators · DFN-8(2x2)
LM193QT from STMicroelectronics, in a DFN-8(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | Out1 | output | Output of comparator 1, with low-level output voltage of 80 mV typ. (400 mV max.) at Isink = 4 mA and output sink current of 6 mA min. at Vid = 1 V, Vo = 1.5 V. |
| 2 | In1- | input | Inverting input of comparator 1; the low input voltage state must not be less than -0.3 V (or 0.3 V below the negative supply, if used). |
| 3 | In1+ | input | Non-inverting input of comparator 1; the common-mode input range is 0 V to (VCC+) - 1.5 V at Tamb = 25 °C, and it includes ground. |
| 4 | Vcc- | power_in | Negative supply pin (ground in single-supply operation); the total supply voltage (VCC+) - (VCC-) is specified from 2 V to 36 V. |
| 5 | In2+ | input | Non-inverting input of comparator 2; the common-mode input range is 0 V to (VCC+) - 1.5 V at Tamb = 25 °C, and it includes ground. |
| 6 | In2- | input | Inverting input of comparator 2; the low input voltage state must not be less than -0.3 V (or 0.3 V below the negative supply, if used). |
| 7 | Out2 | output | Output of comparator 2, with low-level output voltage of 80 mV typ. (400 mV max.) at Isink = 4 mA and output sink current of 6 mA min. at Vid = 1 V, Vo = 1.5 V. |
| 8 | Vcc+ | power_in | Positive supply pin; the total supply voltage (VCC+) - (VCC-) is specified from 2 V to 36 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | DFN-8(2x2) |
| Category | Amplifiers/Comparators |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VCC (absolute maximum) | VCC | 36 | V | Printed as ±18 or 36 V | 4 | ||
| Differential input voltage Vid | Vid | -36 | 36 | V | LM193, LM293, LM393 | 4 | |
| Maximum junction temperature Tj | Tj | 150 | °C | 4 | |||
| Storage temperature range Tstg | Tstg | -65 | 150 | °C | 4 | ||
| Thermal resistance junction to ambient Rthja (DFN8 2x2) | Rthja | 57 | °C/W | DFN8 2x2; footnote 2: values are typical | 4 | ||
| Supply voltage VCC (recommended) | VCC | 2 | 36 | V | (VCC +) - (VCC -) | 5 | |
| Common mode input voltage range Vicm (max (VCC+)-1.5 V) | Vicm | 0 | V | VCC + = 30 V, Tamb = 25 °C | 5 | ||
| Common mode input voltage range Vicm (max (VCC+)-2 V) | Vicm | 0 | V | VCC + = 30 V, Tmin ≤ Tamb ≤ Tmax | 5 | ||
| Operating free-air temperature range Toper (LM193) | Toper | -55 | 125 | °C | LM193 | 5 | |
| Input offset voltage Vio | Vio | 1 | 5 | mV | Vo = 1.4 V, Rs = 0, VCC+ from 5 V to 30 V, full common-mode range (footnote 1) | 6 | |
| Input offset voltage Vio | Vio | 9 | mV | Tmin ≤ Tamb ≤ Tmax | 6 | ||
| Input offset current Iio | Iio | 3 | 50 | nA | 6 | ||
| Input offset current Iio | Iio | 150 | nA | Tmin ≤ Tamb ≤ Tmax | 6 | ||
| Input bias current Iib (I+ or I-) | Iib | 20 | 250 | nA | 6 | ||
| Input bias current Iib (I+ or I-) | Iib | 400 | nA | Tmin ≤ Tamb ≤ Tmax | 6 | ||
| Large signal voltage gain Avd | Avd | 50 | 200 | V/mV | VCC = 15 V, RL = 15 kΩ, Vo = 1 V to 11 V | 6 | |
| Supply current ICC (all comparators) | ICC | 0.45 | 1 | mA | VCC = 5 V, no load | 6 | |
| Supply current ICC (all comparators) | ICC | 0.6 | 2.5 | mA | VCC = 30 V, no load | 6 | |
| Low-level output voltage VOL | VOL | 80 | 400 | mV | Vid = -1 V, Isink = 4 mA | 6 | |
| Low-level output voltage VOL | VOL | 700 | mV | Tmin ≤ Tamb ≤ Tmax | 6 | ||
| High-level output current IOH | IOH | 1 | μA | Tmin ≤ Tamb ≤ Tmax | 6 | ||
| Output sink current Isink | Isink | 6 | 18 | mA | Vid = 1 V, Vo = 1.5 V | 6 | |
| High-level output current IOH | IOH | 0.1 | nA | VCC = Vo = 30 V, Vid = 1 V | 6 | ||
| Response time tre | tre | 1.3 | μs | RL = 5.1 kΩ connected to VCC+; 100 mV input step with 5 mV overdrive (footnote 4) | 6 | ||
| Large signal response time trel | trel | 300 | ns | RL = 5.1 kΩ connected to VCC+, TTL input, V(ref) = 1.4 V | 6 |
CAD (KiCad official)
- Symbol:
LM193QT - Footprint:
Package_DFN_QFN:DFN-8_2x2mm_P0.5mm - 3D model: DFN-8(2x2), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.55 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
lm193qt-etched.step/lm193qt-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm193qt.step/lm193qt.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (18 pp, sha256
31d06d834156345d, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).