Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

STM32L432KCU3

STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · UFQFPN-32(5x5)

STM32L432KCU3 from STMicroelectronics, in a UFQFPN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VDD power_in Main power supply pin; standard operating voltage is 1.71 V to 3.6 V.
2 PC14-OSC32_IN bidirectional FT GPIO supplied through the power switch that sinks or sources only 3 mA, so output use is limited to 2 MHz with a 30 pF load and it must not drive current sources such as LEDs; also OSC32_IN for the 32 kHz crystal.
3 PC15-OSC32_OUT bidirectional FT GPIO supplied through the power switch that sinks or sources only 3 mA, so output use is limited to 2 MHz with a 30 pF load and it must not drive current sources such as LEDs; also OSC32_OUT for the 32 kHz crystal.
4 NRST bidirectional Bidirectional reset pin with embedded weak pull-up resistor.
5 VDDA/VREF+ power_in Analog supply pin with positive ADC reference input; VDDA range is 1.62 V to 3.6 V when the ADC or COMP is used.
6 PA0/CK_IN bidirectional FT_a GPIO with alternate functions TIM2_CH1, USART2_CTS, COMP1_OUT, SAI1_EXTCLK, TIM2_ETR and analog functions OPAMP1_VINP, ADC1_IN5, WKUP1 and CK_IN.
7 PA1 bidirectional FT_a GPIO with alternate functions TIM2_CH2, I2C1_SMBA, SPI1_SCK, USART2_RTS_DE, TIM15_CH1N and analog functions OPAMP1_VINM, COMP1_INP, ADC1_IN6.
8 PA2 bidirectional FT_a GPIO with alternate functions TIM2_CH3, USART2_TX, LPUART1_TX, QUADSPI_BK1_NCS, COMP2_OUT, TIM15_CH1 and analog functions COMP2_INM, ADC1_IN7, WKUP4.
9 PA3 bidirectional TT_a GPIO (3.6 V tolerant) with alternate functions TIM2_CH4, USART2_RX, LPUART1_RX, QUADSPI_CLK, SAI1_MCLK_A, TIM15_CH2 and analog functions OPAMP1_VOUT, COMP2_INP, ADC1_IN8.
10 PA4 bidirectional TT_a GPIO (3.6 V tolerant) with alternate functions SPI1_NSS, SPI3_NSS, USART2_CK, SAI1_FS_B, LPTIM2_OUT and analog functions COMP1_INM, COMP2_INM, ADC1_IN9, DAC1_OUT1; injected current limited to -5/0 mA.
11 PA5 bidirectional TT_a GPIO (3.6 V tolerant) with alternate functions TIM2_CH1, TIM2_ETR, SPI1_SCK, LPTIM2_ETR and analog functions COMP1_INM, COMP2_INM, ADC1_IN10, DAC1_OUT2; injected current limited to -5/0 mA.
12 PA6 bidirectional FT_a GPIO with alternate functions TIM1_BKIN, SPI1_MISO, COMP1_OUT, USART3_CTS, LPUART1_CTS, QUADSPI_BK1_IO3, TIM16_CH1 and analog function ADC1_IN11.
13 PA7 bidirectional FT_fa GPIO (Fm+ capable) with alternate functions TIM1_CH1N, I2C3_SCL, SPI1_MOSI, QUADSPI_BK1_IO2, COMP2_OUT and analog function ADC1_IN12.
14 PB0 bidirectional FT_a GPIO with alternate functions TIM1_CH2N, SPI1_NSS, USART3_CK, QUADSPI_BK1_IO1, COMP1_OUT, SAI1_EXTCLK and analog function ADC1_IN15.
15 PB1 bidirectional FT_a GPIO with alternate functions TIM1_CH3N, USART3_RTS_DE, LPUART1_RTS_DE, QUADSPI_BK1_IO0, LPTIM2_IN1 and analog functions COMP1_INM, ADC1_IN16.
16 VSS power_in Ground pin; must be connected to the same ground as the other VSS pins (variation limited to 50 mV).
17 VDD power_in Main power supply pin; standard operating voltage is 1.71 V to 3.6 V.
18 PA8 bidirectional FT GPIO with alternate functions MCO, TIM1_CH1, USART1_CK, SWPMI1_IO, SAI1_SCK_A, LPTIM2_OUT.
19 PA9 bidirectional FT_f GPIO (Fm+ capable) with alternate functions TIM1_CH2, I2C1_SCL, USART1_TX, SAI1_FS_A, TIM15_BKIN.
20 PA10 bidirectional FT_f GPIO (Fm+ capable) with alternate functions TIM1_CH3, I2C1_SDA, USART1_RX, USB_CRS_SYNC, SAI1_SD_A.
21 PA11 bidirectional FT_u GPIO with USB function supplied by VDDUSB, alternate functions TIM1_CH4, SPI1_MISO, COMP1_OUT, USART1_CTS, CAN1_RX, USB_DM.
22 PA12 bidirectional FT_u GPIO with USB function supplied by VDDUSB, alternate functions TIM1_ETR, SPI1_MOSI, USART1_RTS_DE, CAN1_TX, USB_DP.
23 PA13 (JTMS-SWDIO) bidirectional FT GPIO that after reset is configured as the JTMS-SWDIO debug function with internal pull-up enabled; also IR_OUT, USB_NOE, SWPMI1_TX, SAI1_SD_B.
24 PA14 (JTCK-SWCLK) bidirectional FT GPIO that after reset is configured as the JTCK-SWCLK debug function with internal pull-down enabled; also LPTIM1_OUT, I2C1_SMBA, SWPMI1_RX, SAI1_FS_B.
25 PA15 (JTDI) bidirectional FT GPIO that after reset is configured as the JTDI debug function with internal pull-up enabled; also TIM2_CH1, TIM2_ETR, USART2_RX, SPI1_NSS, SPI3_NSS, USART3_RTS_DE, TSC_G3_IO1.
26 PB3 (JTDO-TRACESWO) bidirectional FT_a GPIO that after reset is configured as the JTDO-TRACESWO debug function; also TIM2_CH2, SPI1_SCK, SPI3_SCK, USART1_RTS_DE, SAI1_SCK_B and analog function COMP2_INM.
27 PB4 (NJTRST) bidirectional FT_fa GPIO that after reset is configured as the NJTRST debug function with internal pull-up enabled; also I2C3_SDA, SPI1_MISO, SPI3_MISO, USART1_CTS, TSC_G2_IO1 and analog function COMP2_INP.
28 PB5 bidirectional FT GPIO with alternate functions LPTIM1_IN1, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI, USART1_CK, TSC_G2_IO2, COMP2_OUT, SAI1_SD_B, TIM16_BKIN.
29 PB6 bidirectional FT_fa GPIO (Fm+ capable) with alternate functions LPTIM1_ETR, I2C1_SCL, USART1_TX, TSC_G2_IO3, SAI1_FS_B, TIM16_CH1N and analog function COMP2_INP.
30 PB7 bidirectional FT_fa GPIO (Fm+ capable) with alternate functions LPTIM1_IN2, I2C1_SDA, USART1_RX, TSC_G2_IO4 and analog functions COMP2_INM, PVD_IN.
31 PH3/BOOT0 bidirectional FT GPIO that also serves as the BOOT0 boot-mode selection input, with EVENTOUT alternate function.
32 VSS power_in Ground pin; must be connected to the same ground as the other VSS pins (variation limited to 50 mV).
33 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package UFQFPN-32(5x5)
Category Embedded Processors & Controllers
Pins 33

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Standard operating voltage VDD 1.71 3.6 V 67
Analog supply voltage, ADC or COMP used VDDA 1.62 3.6 V ADC or COMP used 67
Analog supply voltage, DAC or OPAMP used VDDA 1.8 3.6 V DAC or OPAMP used 67
USB supply voltage VDDUSB 3 3.6 V USB used 67
Internal AHB clock frequency fHCLK 0 80 MHz 67
Internal APB1 clock frequency fPCLK1 0 80 MHz 67
Internal APB2 clock frequency fPCLK2 0 80 MHz 67
Ambient temperature for the suffix 3 version TA -40 125 °C Maximum power dissipation 67
Ambient temperature for the suffix 3 version, low-power dissipation TA -40 130 °C Low-power dissipation 67
Junction temperature range, suffix 3 version TJ -40 130 °C Suffix 3 version 67
Power dissipation at TA = 125 °C for suffix 3, UFQFPN32 PD 128 mW TA = 125 °C for suffix 3 67
External main supply voltage (including VDD, VDDA, VDDUSB) VDDX - VSS -0.3 4 V 65
Storage temperature range TSTG -65 150 °C 66
Maximum junction temperature TJ 150 °C 66
Total current into sum of all VDD power lines (source) ΣIVDD 140 mA 66
Maximum current into each VDD power pin (source) IVDD(PIN) 100 mA 66
Output current sunk by any I/O and control pin except FT_f IIO(PIN) 20 mA 66
Total output current sunk by sum of all I/Os and control pins ΣIIO(PIN) 100 mA 66
Internal reference voltage VREFINT 1.182 1.212 1.232 V -40 °C < TA < +130 °C 70
Temperature coefficient TCoeff 30 50 ppm/°C -40°C < TA < +130°C 70
Voltage coefficient VDDCoeff 250 1200 ppm/V 3.0 V < VDD < 3.6 V 70
Internal reference voltage spread over the temperature range ΔVREFINT 5 7.5 mV VDD = 3 V 70
Brown-out reset threshold 0, rising edge VBOR0 1.62 1.66 1.7 V Rising edge 68
Brown-out reset threshold 0, falling edge VBOR0 1.6 1.64 1.69 V Falling edge 68
HSI16 frequency fHSI16 15.88 16.08 MHz VDD=3.0 V, TA=30 °C 95
HSI16 frequency drift over temperature ΔTemp(HSI16) -1 1 % TA= 0 to 85 °C 95
HSI16 frequency drift over temperature ΔTemp(HSI16) -2 1.5 % TA= -40 to 125 °C 95
HSI16 frequency drift over VDD ΔVDD(HSI16) -0.1 0.05 % VDD=1.62 V to 3.6 V 95
HSI16 user trimming step TRIM 0.2 0.3 0.4 % Trimming code is not a multiple of 64 95
LSI frequency fLSI 31.04 32.96 kHz VDD = 3.0 V, TA = 30 °C 101
LSI frequency fLSI 29.5 34 kHz VDD = 1.62 to 3.6 V, TA = -40 to 125 °C 101
HSI48 accuracy over temperature (factory calibrated) ACCHSI48_REL -3 3 % VDD = 3.0 V to 3.6 V, TA = -15 to 85 °C 100
HSI48 accuracy over temperature (factory calibrated) ACCHSI48_REL -4.5 4.5 % VDD = 1.65 V to 3.6 V, TA = -40 to 125 °C 100
MSI oscillator frequency drift over temperature ΔTEMP(MSI) -8 6 % MSI mode, TA= -40 to 125 °C 98
User external clock source frequency, Voltage scaling Range 1 fHSE_ext 8 48 MHz Voltage scaling Range 1 92
User external clock source frequency, Voltage scaling Range 2 fHSE_ext 8 26 MHz Voltage scaling Range 2 92
Supply current in Standby mode (backup registers retained), RTC disabled, no independent watchdog IDD_ALL(Standby) 90.2 225 nA VDD = 3 V, 25 °C 83
Supply current in Shutdown mode (backup registers retained), RTC disabled IDD_ALL(Shutdown) 44.3 70.1 nA VDD = 3 V, 25 °C 84
Supply current in Stop 2 mode, RTC disabled IDD_ALL(Stop 2) 1.06 2.1 µA VDD = 3 V, 25 °C 79
Supply current in Run mode, Range 1, all peripherals disabled, code from Flash IDD_ALL(Run) 8.53 9.5 mA fHCLK = 80 MHz, Range 1, 25 °C, ART enable (Cache ON Prefetch OFF) 73
Supply current in Sleep mode, Range 1 IDD_ALL(Sleep) 2.23 2.5 mA fHCLK = 80 MHz, Range 1, 25 °C, all peripherals disabled 78
Injected current on FT_xxx, TT_xx, RST and B pins, except PA4, PA5 IINJ(PIN) -5 0 mA 66
LSE current consumption, low drive capability IDD(LSE) 250 nA LSEDRV[1:0] = 00 94
MSI frequency after factory calibration, Range 11 fMSI 47.38 48 48.62 MHz MSI mode, VDD=3 V and TA=30 °C 97
HSI48 frequency fHSI48 48 MHz VDD=3.0V, TA=30°C 100

CAD (KiCad official)

  • Symbol: STM32L432KCU3
  • Footprint: Package_DFN_QFN:UFQFPN-32-1EP_5x5mm_P0.5mm_EP3.5x3.5mm
  • 3D model: UFQFPN-32(5x5) (KiCad packages3D, STEP)
  • 3D model files: stm32l432kcu3-etched.step / stm32l432kcu3-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stm32l432kcu3.step / stm32l432kcu3.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (156 pp, sha256 411517499bfbb10c, retrieved 2026-11-06, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF