Generated by kicad-footprint-generator · KiCad file format 20260206
STM32L432KCU3
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · UFQFPN-32(5x5)
STM32L432KCU3 from STMicroelectronics, in a UFQFPN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Main power supply pin; standard operating voltage is 1.71 V to 3.6 V. |
| 2 | PC14-OSC32_IN | bidirectional | FT GPIO supplied through the power switch that sinks or sources only 3 mA, so output use is limited to 2 MHz with a 30 pF load and it must not drive current sources such as LEDs; also OSC32_IN for the 32 kHz crystal. |
| 3 | PC15-OSC32_OUT | bidirectional | FT GPIO supplied through the power switch that sinks or sources only 3 mA, so output use is limited to 2 MHz with a 30 pF load and it must not drive current sources such as LEDs; also OSC32_OUT for the 32 kHz crystal. |
| 4 | NRST | bidirectional | Bidirectional reset pin with embedded weak pull-up resistor. |
| 5 | VDDA/VREF+ | power_in | Analog supply pin with positive ADC reference input; VDDA range is 1.62 V to 3.6 V when the ADC or COMP is used. |
| 6 | PA0/CK_IN | bidirectional | FT_a GPIO with alternate functions TIM2_CH1, USART2_CTS, COMP1_OUT, SAI1_EXTCLK, TIM2_ETR and analog functions OPAMP1_VINP, ADC1_IN5, WKUP1 and CK_IN. |
| 7 | PA1 | bidirectional | FT_a GPIO with alternate functions TIM2_CH2, I2C1_SMBA, SPI1_SCK, USART2_RTS_DE, TIM15_CH1N and analog functions OPAMP1_VINM, COMP1_INP, ADC1_IN6. |
| 8 | PA2 | bidirectional | FT_a GPIO with alternate functions TIM2_CH3, USART2_TX, LPUART1_TX, QUADSPI_BK1_NCS, COMP2_OUT, TIM15_CH1 and analog functions COMP2_INM, ADC1_IN7, WKUP4. |
| 9 | PA3 | bidirectional | TT_a GPIO (3.6 V tolerant) with alternate functions TIM2_CH4, USART2_RX, LPUART1_RX, QUADSPI_CLK, SAI1_MCLK_A, TIM15_CH2 and analog functions OPAMP1_VOUT, COMP2_INP, ADC1_IN8. |
| 10 | PA4 | bidirectional | TT_a GPIO (3.6 V tolerant) with alternate functions SPI1_NSS, SPI3_NSS, USART2_CK, SAI1_FS_B, LPTIM2_OUT and analog functions COMP1_INM, COMP2_INM, ADC1_IN9, DAC1_OUT1; injected current limited to -5/0 mA. |
| 11 | PA5 | bidirectional | TT_a GPIO (3.6 V tolerant) with alternate functions TIM2_CH1, TIM2_ETR, SPI1_SCK, LPTIM2_ETR and analog functions COMP1_INM, COMP2_INM, ADC1_IN10, DAC1_OUT2; injected current limited to -5/0 mA. |
| 12 | PA6 | bidirectional | FT_a GPIO with alternate functions TIM1_BKIN, SPI1_MISO, COMP1_OUT, USART3_CTS, LPUART1_CTS, QUADSPI_BK1_IO3, TIM16_CH1 and analog function ADC1_IN11. |
| 13 | PA7 | bidirectional | FT_fa GPIO (Fm+ capable) with alternate functions TIM1_CH1N, I2C3_SCL, SPI1_MOSI, QUADSPI_BK1_IO2, COMP2_OUT and analog function ADC1_IN12. |
| 14 | PB0 | bidirectional | FT_a GPIO with alternate functions TIM1_CH2N, SPI1_NSS, USART3_CK, QUADSPI_BK1_IO1, COMP1_OUT, SAI1_EXTCLK and analog function ADC1_IN15. |
| 15 | PB1 | bidirectional | FT_a GPIO with alternate functions TIM1_CH3N, USART3_RTS_DE, LPUART1_RTS_DE, QUADSPI_BK1_IO0, LPTIM2_IN1 and analog functions COMP1_INM, ADC1_IN16. |
| 16 | VSS | power_in | Ground pin; must be connected to the same ground as the other VSS pins (variation limited to 50 mV). |
| 17 | VDD | power_in | Main power supply pin; standard operating voltage is 1.71 V to 3.6 V. |
| 18 | PA8 | bidirectional | FT GPIO with alternate functions MCO, TIM1_CH1, USART1_CK, SWPMI1_IO, SAI1_SCK_A, LPTIM2_OUT. |
| 19 | PA9 | bidirectional | FT_f GPIO (Fm+ capable) with alternate functions TIM1_CH2, I2C1_SCL, USART1_TX, SAI1_FS_A, TIM15_BKIN. |
| 20 | PA10 | bidirectional | FT_f GPIO (Fm+ capable) with alternate functions TIM1_CH3, I2C1_SDA, USART1_RX, USB_CRS_SYNC, SAI1_SD_A. |
| 21 | PA11 | bidirectional | FT_u GPIO with USB function supplied by VDDUSB, alternate functions TIM1_CH4, SPI1_MISO, COMP1_OUT, USART1_CTS, CAN1_RX, USB_DM. |
| 22 | PA12 | bidirectional | FT_u GPIO with USB function supplied by VDDUSB, alternate functions TIM1_ETR, SPI1_MOSI, USART1_RTS_DE, CAN1_TX, USB_DP. |
| 23 | PA13 (JTMS-SWDIO) | bidirectional | FT GPIO that after reset is configured as the JTMS-SWDIO debug function with internal pull-up enabled; also IR_OUT, USB_NOE, SWPMI1_TX, SAI1_SD_B. |
| 24 | PA14 (JTCK-SWCLK) | bidirectional | FT GPIO that after reset is configured as the JTCK-SWCLK debug function with internal pull-down enabled; also LPTIM1_OUT, I2C1_SMBA, SWPMI1_RX, SAI1_FS_B. |
| 25 | PA15 (JTDI) | bidirectional | FT GPIO that after reset is configured as the JTDI debug function with internal pull-up enabled; also TIM2_CH1, TIM2_ETR, USART2_RX, SPI1_NSS, SPI3_NSS, USART3_RTS_DE, TSC_G3_IO1. |
| 26 | PB3 (JTDO-TRACESWO) | bidirectional | FT_a GPIO that after reset is configured as the JTDO-TRACESWO debug function; also TIM2_CH2, SPI1_SCK, SPI3_SCK, USART1_RTS_DE, SAI1_SCK_B and analog function COMP2_INM. |
| 27 | PB4 (NJTRST) | bidirectional | FT_fa GPIO that after reset is configured as the NJTRST debug function with internal pull-up enabled; also I2C3_SDA, SPI1_MISO, SPI3_MISO, USART1_CTS, TSC_G2_IO1 and analog function COMP2_INP. |
| 28 | PB5 | bidirectional | FT GPIO with alternate functions LPTIM1_IN1, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI, USART1_CK, TSC_G2_IO2, COMP2_OUT, SAI1_SD_B, TIM16_BKIN. |
| 29 | PB6 | bidirectional | FT_fa GPIO (Fm+ capable) with alternate functions LPTIM1_ETR, I2C1_SCL, USART1_TX, TSC_G2_IO3, SAI1_FS_B, TIM16_CH1N and analog function COMP2_INP. |
| 30 | PB7 | bidirectional | FT_fa GPIO (Fm+ capable) with alternate functions LPTIM1_IN2, I2C1_SDA, USART1_RX, TSC_G2_IO4 and analog functions COMP2_INM, PVD_IN. |
| 31 | PH3/BOOT0 | bidirectional | FT GPIO that also serves as the BOOT0 boot-mode selection input, with EVENTOUT alternate function. |
| 32 | VSS | power_in | Ground pin; must be connected to the same ground as the other VSS pins (variation limited to 50 mV). |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | UFQFPN-32(5x5) |
| Category | Embedded Processors & Controllers |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Standard operating voltage | VDD | 1.71 | 3.6 | V | 67 | ||
| Analog supply voltage, ADC or COMP used | VDDA | 1.62 | 3.6 | V | ADC or COMP used | 67 | |
| Analog supply voltage, DAC or OPAMP used | VDDA | 1.8 | 3.6 | V | DAC or OPAMP used | 67 | |
| USB supply voltage | VDDUSB | 3 | 3.6 | V | USB used | 67 | |
| Internal AHB clock frequency | fHCLK | 0 | 80 | MHz | 67 | ||
| Internal APB1 clock frequency | fPCLK1 | 0 | 80 | MHz | 67 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 80 | MHz | 67 | ||
| Ambient temperature for the suffix 3 version | TA | -40 | 125 | °C | Maximum power dissipation | 67 | |
| Ambient temperature for the suffix 3 version, low-power dissipation | TA | -40 | 130 | °C | Low-power dissipation | 67 | |
| Junction temperature range, suffix 3 version | TJ | -40 | 130 | °C | Suffix 3 version | 67 | |
| Power dissipation at TA = 125 °C for suffix 3, UFQFPN32 | PD | 128 | mW | TA = 125 °C for suffix 3 | 67 | ||
| External main supply voltage (including VDD, VDDA, VDDUSB) | VDDX - VSS | -0.3 | 4 | V | 65 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 66 | ||
| Maximum junction temperature | TJ | 150 | °C | 66 | |||
| Total current into sum of all VDD power lines (source) | ΣIVDD | 140 | mA | 66 | |||
| Maximum current into each VDD power pin (source) | IVDD(PIN) | 100 | mA | 66 | |||
| Output current sunk by any I/O and control pin except FT_f | IIO(PIN) | 20 | mA | 66 | |||
| Total output current sunk by sum of all I/Os and control pins | ΣIIO(PIN) | 100 | mA | 66 | |||
| Internal reference voltage | VREFINT | 1.182 | 1.212 | 1.232 | V | -40 °C < TA < +130 °C | 70 |
| Temperature coefficient | TCoeff | 30 | 50 | ppm/°C | -40°C < TA < +130°C | 70 | |
| Voltage coefficient | VDDCoeff | 250 | 1200 | ppm/V | 3.0 V < VDD < 3.6 V | 70 | |
| Internal reference voltage spread over the temperature range | ΔVREFINT | 5 | 7.5 | mV | VDD = 3 V | 70 | |
| Brown-out reset threshold 0, rising edge | VBOR0 | 1.62 | 1.66 | 1.7 | V | Rising edge | 68 |
| Brown-out reset threshold 0, falling edge | VBOR0 | 1.6 | 1.64 | 1.69 | V | Falling edge | 68 |
| HSI16 frequency | fHSI16 | 15.88 | 16.08 | MHz | VDD=3.0 V, TA=30 °C | 95 | |
| HSI16 frequency drift over temperature | ΔTemp(HSI16) | -1 | 1 | % | TA= 0 to 85 °C | 95 | |
| HSI16 frequency drift over temperature | ΔTemp(HSI16) | -2 | 1.5 | % | TA= -40 to 125 °C | 95 | |
| HSI16 frequency drift over VDD | ΔVDD(HSI16) | -0.1 | 0.05 | % | VDD=1.62 V to 3.6 V | 95 | |
| HSI16 user trimming step | TRIM | 0.2 | 0.3 | 0.4 | % | Trimming code is not a multiple of 64 | 95 |
| LSI frequency | fLSI | 31.04 | 32.96 | kHz | VDD = 3.0 V, TA = 30 °C | 101 | |
| LSI frequency | fLSI | 29.5 | 34 | kHz | VDD = 1.62 to 3.6 V, TA = -40 to 125 °C | 101 | |
| HSI48 accuracy over temperature (factory calibrated) | ACCHSI48_REL | -3 | 3 | % | VDD = 3.0 V to 3.6 V, TA = -15 to 85 °C | 100 | |
| HSI48 accuracy over temperature (factory calibrated) | ACCHSI48_REL | -4.5 | 4.5 | % | VDD = 1.65 V to 3.6 V, TA = -40 to 125 °C | 100 | |
| MSI oscillator frequency drift over temperature | ΔTEMP(MSI) | -8 | 6 | % | MSI mode, TA= -40 to 125 °C | 98 | |
| User external clock source frequency, Voltage scaling Range 1 | fHSE_ext | 8 | 48 | MHz | Voltage scaling Range 1 | 92 | |
| User external clock source frequency, Voltage scaling Range 2 | fHSE_ext | 8 | 26 | MHz | Voltage scaling Range 2 | 92 | |
| Supply current in Standby mode (backup registers retained), RTC disabled, no independent watchdog | IDD_ALL(Standby) | 90.2 | 225 | nA | VDD = 3 V, 25 °C | 83 | |
| Supply current in Shutdown mode (backup registers retained), RTC disabled | IDD_ALL(Shutdown) | 44.3 | 70.1 | nA | VDD = 3 V, 25 °C | 84 | |
| Supply current in Stop 2 mode, RTC disabled | IDD_ALL(Stop 2) | 1.06 | 2.1 | µA | VDD = 3 V, 25 °C | 79 | |
| Supply current in Run mode, Range 1, all peripherals disabled, code from Flash | IDD_ALL(Run) | 8.53 | 9.5 | mA | fHCLK = 80 MHz, Range 1, 25 °C, ART enable (Cache ON Prefetch OFF) | 73 | |
| Supply current in Sleep mode, Range 1 | IDD_ALL(Sleep) | 2.23 | 2.5 | mA | fHCLK = 80 MHz, Range 1, 25 °C, all peripherals disabled | 78 | |
| Injected current on FT_xxx, TT_xx, RST and B pins, except PA4, PA5 | IINJ(PIN) | -5 | 0 | mA | 66 | ||
| LSE current consumption, low drive capability | IDD(LSE) | 250 | nA | LSEDRV[1:0] = 00 | 94 | ||
| MSI frequency after factory calibration, Range 11 | fMSI | 47.38 | 48 | 48.62 | MHz | MSI mode, VDD=3 V and TA=30 °C | 97 |
| HSI48 frequency | fHSI48 | 48 | MHz | VDD=3.0V, TA=30°C | 100 |
CAD (KiCad official)
- Symbol:
STM32L432KCU3 - Footprint:
Package_DFN_QFN:UFQFPN-32-1EP_5x5mm_P0.5mm_EP3.5x3.5mm - 3D model: UFQFPN-32(5x5) (KiCad packages3D, STEP)
- 3D model files:
stm32l432kcu3-etched.step/stm32l432kcu3-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32l432kcu3.step/stm32l432kcu3.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (156 pp, sha256
411517499bfbb10c, retrieved 2026-11-06, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).