3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT3008ETS8-3.3#TRMPBF
Analog Devices · Linear Voltage Regulators (LDO) · TSOT-23-8
LT3008ETS8-3.3#TRMPBF from Analog Devices, in a TSOT-23-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SHDN | input | Shutdown input: pulling it low puts the LT3008 into a low-power state and turns the output off, and it must be tied to VIN if unused; it cannot be driven below GND unless tied to IN and does not function if left unconnected. |
| 2 | GND | power_in | Ground; connect the bottom of the output-setting resistor divider directly to GND for the best regulation. |
| 3 | GND | power_in | Ground; connect the bottom of the output-setting resistor divider directly to GND for the best regulation. |
| 4 | GND | power_in | Ground; connect the bottom of the output-setting resistor divider directly to GND for the best regulation. |
| 5 | IN | power_in | Input supply pin; a bypass capacitor in the range of 0.1µF to 10µF is advised when the device is more than six inches from the main input filter capacitor, and the pin withstands reverse voltage without reverse current flow. |
| 6 | OUT | power_out | Regulated output that supplies the load; a minimum output capacitor of 2.2µF is required to prevent oscillations. |
| 7 | ADJ/SENSE | input | For the fixed 3.3V version this is the SENSE input to the error amplifier, best connected to OUT (or to the load for Kelvin sensing) with 1µA typical bias current, and it can be pulled below ground in dual-supply systems. |
| 8 | NC | unconnected | No connect in the TSOT-23 package; not tied to internal circuitry, so it may be floated, tied to VIN, or tied to GND. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | TSOT-23-8 |
| Category | Power Supply Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Voltage | 2 | 45 | V | 4 | |||
| Regulated Output Voltage (LT3008-3.3) | 3.267 | 3.3 | 3.333 | V | LT3008-3.3: VIN = 3.85V, ILOAD = 100μA | 4 | |
| Regulated Output Voltage (LT3008-3.3, full operating temperature range) | 3.234 | 3.3 | 3.366 | V | 3.85V < VIN < 45V, 1μA < ILOAD < 20mA; l = full operating temperature range | 4 | |
| Line Regulation (LT3008-3.3) | 3.3 | 16.5 | mV | ΔVIN = 3.85V to 45V, ILOAD = 1mA; max over l range | 4 | ||
| Load Regulation (LT3008-3.3) | 2.2 | 11 | mV | VIN = 3.85V, ILOAD = 1μA to 10mA; max over l range | 5 | ||
| Load Regulation (LT3008-3.3) | 2.8 | 28 | mV | VIN = 3.85V, ILOAD = 1μA to 20mA; max over l range | 5 | ||
| Dropout Voltage | 115 | 180 | mV | VIN = VOUT(NOMINAL), ILOAD = 100μA | 5 | ||
| Dropout Voltage | 250 | mV | VIN = VOUT(NOMINAL), ILOAD = 100μA; l = full operating temperature range | 5 | |||
| Dropout Voltage | 170 | 250 | mV | VIN = VOUT(NOMINAL), ILOAD = 1mA | 5 | ||
| Dropout Voltage | 350 | mV | VIN = VOUT(NOMINAL), ILOAD = 1mA; l = full operating temperature range | 5 | |||
| Dropout Voltage | 270 | 340 | mV | VIN = VOUT(NOMINAL), ILOAD = 10mA | 5 | ||
| Dropout Voltage | 470 | mV | VIN = VOUT(NOMINAL), ILOAD = 10mA; l = full operating temperature range | 5 | |||
| Dropout Voltage | 300 | 365 | mV | VIN = VOUT(NOMINAL), ILOAD = 20mA | 5 | ||
| Dropout Voltage | 500 | mV | VIN = VOUT(NOMINAL), ILOAD = 20mA; l = full operating temperature range | 5 | |||
| Quiescent Current | 3 | μA | ILOAD = 0μA | 5 | |||
| Quiescent Current | 6 | μA | ILOAD = 0μA; l = full operating temperature range | 5 | |||
| GND Pin Current | 3 | 6 | μA | VIN = VOUT(NOMINAL) + 0.5V, ILOAD = 0μA; max over l range | 5 | ||
| GND Pin Current | 6 | 12 | μA | VIN = VOUT(NOMINAL) + 0.5V, ILOAD = 100μA; max over l range | 5 | ||
| GND Pin Current | 21 | 50 | μA | VIN = VOUT(NOMINAL) + 0.5V, ILOAD = 1mA; max over l range | 5 | ||
| GND Pin Current | 160 | 500 | μA | VIN = VOUT(NOMINAL) + 0.5V, ILOAD = 10mA; max over l range | 5 | ||
| GND Pin Current | 350 | 1200 | μA | VIN = VOUT(NOMINAL) + 0.5V, ILOAD = 20mA; max over l range | 5 | ||
| Output Voltage Noise | 92 | μVRMS | COUT = 2.2μF, ILOAD = 20mA, BW = 10Hz to 100kHz | 5 | |||
| Shutdown Threshold (VOUT Off to On) | 0.67 | 1.5 | V | VOUT = Off to On; l = full operating temperature range | 5 | ||
| Shutdown Threshold (VOUT On to Off) | 0.25 | 0.61 | V | VOUT = On to Off; l = full operating temperature range | 5 | ||
| SHDN Pin Current | 0.65 | 2 | μA | VSHDN = 0V, VIN = 45V | 5 | ||
| SHDN Pin Current | -1 | 1 | μA | VSHDN = 45V, VIN = 45V; l = full operating temperature range | 5 | ||
| Quiescent Current in Shutdown | 1 | μA | VIN = 6V, VSHDN = 0V; l = full operating temperature range | 5 | |||
| Ripple Rejection (LT3008-3.3) | 49 | 61 | dB | VIN, VOUT = 2V, VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 20mA | 5 | ||
| Current Limit | 75 | mA | VIN = 45V, VOUT = 0 | 6 | |||
| Current Limit | 22 | mA | VIN = VOUT(NOMINAL) + 1V, ΔVOUT = -5%; l = full operating temperature range | 6 | |||
| Input Reverse-Leakage Current | 1 | 30 | μA | VIN = -45V, VOUT = 0; max over l range | 6 | ||
| Reverse-Output Current | 0.6 | 10 | μA | VOUT = 1.2V, VIN = 0 | 6 | ||
| SENSE Pin Bias Current (fixed output versions) | 1 | μA | at the nominal rated output voltage | 11 | |||
| IN Pin Voltage | -50 | 50 | V | 2 | |||
| OUT Pin Voltage | -50 | 50 | V | 2 | |||
| Input-to-Output Differential Voltage | -50 | 50 | V | 2 | |||
| ADJ Pin Voltage | -50 | 50 | V | 2 | |||
| SENSE Pin Voltage | -50 | 50 | V | 2 | |||
| SHDN Pin Voltage | -50 | 50 | V | Note 8 | 2 | ||
| Operating Junction Temperature Range (E grade) | -40 | 125 | °C | E grade | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Lead Temperature (Soldering, 10 sec) | 300 | °C | TS8 package only | 2 | |||
| Thermal Resistance, Junction-to-Ambient (TSOT-23 package) | θJA | 65 | 85 | °C/W | TS8 package; depends on copper area, 2-layer 1 oz FR-4 board (Table 3: 65°C/W at 2500mm² to 85°C/W at 50mm²) | 2 | |
| Thermal Resistance, Junction-to-Ambient (TSOT-23, 4-layer board with thermal vias) | θJA | 45 | °C/W | 4-layer, 1 oz copper PCB, 3 fused TSOT-23 GND pins to inner GND planes | 15 | ||
| Thermal Shutdown Threshold | 160 | °C | 15 |
CAD (KiCad official)
- Symbol:
LT3008ETS8-3.3#TRMPBF - Footprint:
Package_TO_SOT_SMD:TSOT-23-8 - 3D model: TSOT-23-8 (KiCad packages3D, STEP)
- 3D model files:
lt3008ets8-3-3-trmpbf-etched.step/lt3008ets8-3-3-trmpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3008ets8-3-3-trmpbf.step/lt3008ets8-3-3-trmpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (20 pp, sha256
1def3249b43dc637, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).