Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

URB1D24LD-20WR3

YLPTEC · Power Modules · DIP-6

URB1D24LD-20WR3 from YLPTEC, in a DIP-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table and the footprint is an Adom_Gen land derived from the manufacturer drawing; the 3D model is generated to fit it.

Pinout

Pin Name Type Function
1 +Vin power_in Positive input terminal of the 110VDC nominal series, rated for an input range of 40-160 VDC with a 180 VDC surge (Isec.max) limit; exceeding the input maximum may cause permanent damage.
2 -Vin power_in Negative input terminal, serving as the input return; the CTRL pin voltage is specified relative to this pin.
3 CTRL input Remote on/off control: leave floating or apply TTL high (3.5-12 VDC) to enable the module, and connect to GND or low (0-1.2 VDC) to disable it, with input shutdown current of 2 mA typ. and 7 mA max.
4 Trim passive Pin printed as Trim in the pinout table; the output characteristics table states that the output voltage has no adjustment terminal (无调节端), so no adjustment function is confirmed for this model.
5 -Vo power_out Negative output terminal of the 24 V output, rated 833 mA max (0% to 100% load) with a maximum capacitive load of 470 µF.
6 +Vo power_out Positive output terminal of the 24 V output, with sustained self-recovering short-circuit protection and output overvoltage protection at 110%-160% Vo.

Key specifications

Parameter Value
Manufacturer YLPTEC
Package DIP-6
Category Power Management
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage range (nominal 110 VDC) Vin 40 110 160 VDC 110 VDC nominal input series; typ is the nominal value 1
Input current, full load (24V output) 212 217 mA Full load; 110VDC nominal input series, nominal input voltage, 24V row 2
Input current, no load (24V output) 3 8 mA No load; 110VDC nominal input series, nominal input voltage, 24V row 2
Reflected ripple current 40 mA Nominal input voltage 2
Surge voltage (Isec.max) -0.7 180 VDC 110VDC nominal input series 2
Start-up voltage 40 VDC 110VDC nominal input series 2
Input undervoltage protection 28 33 110VDC nominal input series 2
Start-up time 10 mS Nominal input voltage and constant resistance load 2
Remote control high level (module on) Ctrl 3.5 12 VDC Ctrl floating or TTL high level 2
Remote control low level (module off) Ctrl 0 1.2 VDC Ctrl connected to GND or low level 2
Input current when shut down 2 7 mA Module shut down (Ctrl low) 2
Output voltage (nominal) 24 Vdc Nominal output voltage, single output 1
Output current 0 833 mA Output current range, 24V model 1
Maximum capacitive load 470 μF Exceeding this value prevents normal start-up 1
Efficiency at full load 85 87 % Full load 1
Output voltage accuracy (+Vo1) -2 1 2 % Typ ±1.0%, max ±2.0% as printed; full load range 2
Line regulation (+Vo1) -0.5 0.2 0.5 % Input voltage range; typ ±0.2%, max ±0.5% as printed 2
Load regulation (+Vo1) -1 0.5 1 % 20%~100% rated load, balanced load; typ ±0.5%, max ±1% as printed 2
Ripple and noise (+Vo1), peak-to-peak 50 80 mVp-p Pure resistive load, 20MHz bandwidth, peak-to-peak 2
Startup delay time 1 ms 2
Dynamic response step deviation (+Vo1) -5 3 5 % 25% nominal load step; typ ±3.0%, max ±5.0% as printed 2
Dynamic response recovery time (+Vo1) 300 500 μs 25% nominal load step 2
Output overvoltage protection 110 160 % Vo Full input voltage range 2
Output overcurrent protection 110 150 200 % Io Full input voltage range 2
Isolation voltage 1500 VDC Input-output, 1 minute test, leakage current less than 1 mA 3
Insulation resistance 1000 MΩ Input-output, insulation voltage 500VDC 3
Isolation capacitance 1000 pF Input-output, 100KHz/0.1V 3
Operating temperature -40 85 ℃ Use with reference to the derating curve 3
Storage temperature -40 125 ℃ 3
Maximum working case temperature -55 100 ℃ Working maximum case temperature 3
Storage humidity 5 95 %RH No condensation 3
Pin soldering temperature 300 ℃ Solder joint 1.5 mm from case, 10 seconds 3
Switching frequency 250 KHz PWM mode 3

CAD (Adom-generated)

  • Symbol: URB1D24LD-20WR3
  • Footprint: Adom_Gen:YLPTEC_URB1_561e39
  • 3D model: DIP-6, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 12.0 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: urb1d24ld-20wr3-etched.step / urb1d24ld-20wr3-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); urb1d24ld-20wr3.step / urb1d24ld-20wr3.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: YLPTEC datasheet (6 pp, sha256 069e99b48ea61255, retrieved 2026-11-12, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing. 3D model generated to fit that land.

Datasheet PDF