component
URB1D24LD-20WR3
Public Made by Adomby adom
YLPTEC Power Modules, DIP-6. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownURB1D24LD-20WR3
YLPTEC · Power Modules · DIP-6
URB1D24LD-20WR3 from YLPTEC, in a DIP-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table and the footprint is an Adom_Gen land derived from the manufacturer drawing; the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | +Vin | power_in | Positive input terminal of the 110VDC nominal series, rated for an input range of 40-160 VDC with a 180 VDC surge (Isec.max) limit; exceeding the input maximum may cause permanent damage. |
| 2 | -Vin | power_in | Negative input terminal, serving as the input return; the CTRL pin voltage is specified relative to this pin. |
| 3 | CTRL | input | Remote on/off control: leave floating or apply TTL high (3.5-12 VDC) to enable the module, and connect to GND or low (0-1.2 VDC) to disable it, with input shutdown current of 2 mA typ. and 7 mA max. |
| 4 | Trim | passive | Pin printed as Trim in the pinout table; the output characteristics table states that the output voltage has no adjustment terminal (无调节端), so no adjustment function is confirmed for this model. |
| 5 | -Vo | power_out | Negative output terminal of the 24 V output, rated 833 mA max (0% to 100% load) with a maximum capacitive load of 470 µF. |
| 6 | +Vo | power_out | Positive output terminal of the 24 V output, with sustained self-recovering short-circuit protection and output overvoltage protection at 110%-160% Vo. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | YLPTEC |
| Package | DIP-6 |
| Category | Power Management |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage range (nominal 110 VDC) | Vin | 40 | 110 | 160 | VDC | 110 VDC nominal input series; typ is the nominal value | 1 |
| Input current, full load (24V output) | 212 | 217 | mA | Full load; 110VDC nominal input series, nominal input voltage, 24V row | 2 | ||
| Input current, no load (24V output) | 3 | 8 | mA | No load; 110VDC nominal input series, nominal input voltage, 24V row | 2 | ||
| Reflected ripple current | 40 | mA | Nominal input voltage | 2 | |||
| Surge voltage (Isec.max) | -0.7 | 180 | VDC | 110VDC nominal input series | 2 | ||
| Start-up voltage | 40 | VDC | 110VDC nominal input series | 2 | |||
| Input undervoltage protection | 28 | 33 | 110VDC nominal input series | 2 | |||
| Start-up time | 10 | mS | Nominal input voltage and constant resistance load | 2 | |||
| Remote control high level (module on) | Ctrl | 3.5 | 12 | VDC | Ctrl floating or TTL high level | 2 | |
| Remote control low level (module off) | Ctrl | 0 | 1.2 | VDC | Ctrl connected to GND or low level | 2 | |
| Input current when shut down | 2 | 7 | mA | Module shut down (Ctrl low) | 2 | ||
| Output voltage (nominal) | 24 | Vdc | Nominal output voltage, single output | 1 | |||
| Output current | 0 | 833 | mA | Output current range, 24V model | 1 | ||
| Maximum capacitive load | 470 | μF | Exceeding this value prevents normal start-up | 1 | |||
| Efficiency at full load | 85 | 87 | % | Full load | 1 | ||
| Output voltage accuracy (+Vo1) | -2 | 1 | 2 | % | Typ ±1.0%, max ±2.0% as printed; full load range | 2 | |
| Line regulation (+Vo1) | -0.5 | 0.2 | 0.5 | % | Input voltage range; typ ±0.2%, max ±0.5% as printed | 2 | |
| Load regulation (+Vo1) | -1 | 0.5 | 1 | % | 20%~100% rated load, balanced load; typ ±0.5%, max ±1% as printed | 2 | |
| Ripple and noise (+Vo1), peak-to-peak | 50 | 80 | mVp-p | Pure resistive load, 20MHz bandwidth, peak-to-peak | 2 | ||
| Startup delay time | 1 | ms | 2 | ||||
| Dynamic response step deviation (+Vo1) | -5 | 3 | 5 | % | 25% nominal load step; typ ±3.0%, max ±5.0% as printed | 2 | |
| Dynamic response recovery time (+Vo1) | 300 | 500 | μs | 25% nominal load step | 2 | ||
| Output overvoltage protection | 110 | 160 | % Vo | Full input voltage range | 2 | ||
| Output overcurrent protection | 110 | 150 | 200 | % Io | Full input voltage range | 2 | |
| Isolation voltage | 1500 | VDC | Input-output, 1 minute test, leakage current less than 1 mA | 3 | |||
| Insulation resistance | 1000 | MΩ | Input-output, insulation voltage 500VDC | 3 | |||
| Isolation capacitance | 1000 | pF | Input-output, 100KHz/0.1V | 3 | |||
| Operating temperature | -40 | 85 | ℃ | Use with reference to the derating curve | 3 | ||
| Storage temperature | -40 | 125 | ℃ | 3 | |||
| Maximum working case temperature | -55 | 100 | ℃ | Working maximum case temperature | 3 | ||
| Storage humidity | 5 | 95 | %RH | No condensation | 3 | ||
| Pin soldering temperature | 300 | ℃ | Solder joint 1.5 mm from case, 10 seconds | 3 | |||
| Switching frequency | 250 | KHz | PWM mode | 3 |
CAD (Adom-generated)
- Symbol:
URB1D24LD-20WR3 - Footprint:
Adom_Gen:YLPTEC_URB1_561e39 - 3D model: DIP-6, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 12.0 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
urb1d24ld-20wr3-etched.step/urb1d24ld-20wr3-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);urb1d24ld-20wr3.step/urb1d24ld-20wr3.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: YLPTEC datasheet (6 pp, sha256
069e99b48ea61255, retrieved 2026-11-12, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing. 3D model generated to fit that land.