3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownPIC18F65J11-I
Microchip Tech · Microcontroller Units (MCUs/MPUs/SOCs) · TQFP-64(10x10)
PIC18F65J11-I from Microchip Tech, in a TQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RE1/WR | bidirectional | Digital I/O (PORTE<1>) that serves as the Parallel Slave Port write enable control input (WR), with input tolerance limited to VDD. |
| 2 | RE0/RD | bidirectional | Digital I/O (PORTE<0>) that serves as the Parallel Slave Port read enable control input (RD), with input tolerance limited to VDD. |
| 3 | RG0 | bidirectional | Digital I/O (PORTG<0>) with Schmitt Trigger input, with input tolerance limited to VDD. |
| 4 | RG1/TX2/CK2 | bidirectional | Digital I/O (PORTG<1>), or AUSART asynchronous transmit (TX2) or synchronous clock (CK2). |
| 5 | RG2/RX2/DT2 | bidirectional | Digital I/O (PORTG<2>), or AUSART asynchronous receive (RX2) or synchronous data (DT2), with input tolerance limited to VDD. |
| 6 | RG3 | bidirectional | Digital I/O (PORTG<3>) with Schmitt Trigger input, with input tolerance limited to VDD. |
| 7 | MCLR | input | Master Clear input or programming voltage input; this pin is an active-low Reset to the device. |
| 8 | RG4 | bidirectional | Digital I/O (PORTG<4>) with Schmitt Trigger input that tolerates voltages up to 5.5V. |
| 9 | VSS | power_in | Ground reference for logic and I/O pins. |
| 10 | VDDCORE/VCAP | power_in | Core logic power supply (VDDCORE) when the regulator is disabled, or external filter capacitor connection (VCAP) when the regulator is enabled. |
| 11 | RF7/AN5/SS | bidirectional | Digital I/O (PORTF<7>), analog input 5, or SPI slave select input (SS) for the MSSP module. |
| 12 | RF6/AN11 | bidirectional | Digital I/O (PORTF<6>) or analog input 11. |
| 13 | RF5/AN10/CVREF | bidirectional | Digital I/O (PORTF<5>), analog input 10, or comparator voltage reference output (CVREF). |
| 14 | RF4/AN9 | bidirectional | Digital I/O (PORTF<4>) or analog input 9. |
| 15 | RF3/AN8 | bidirectional | Digital I/O (PORTF<3>) or analog input 8. |
| 16 | RF2/AN7/C1OUT | bidirectional | Digital I/O (PORTF<2>), analog input 7, or comparator 1 output (C1OUT). |
| 17 | RF1/AN6/C2OUT | bidirectional | Digital I/O (PORTF<1>), analog input 6, or comparator 2 output (C2OUT). |
| 18 | ENVREG | input | Enable for the on-chip voltage regulator; tying it to VDD enables the regulator and tying it to ground disables it. |
| 19 | AVDD | power_in | Positive supply for analog modules. |
| 20 | AVSS | power_in | Ground reference for analog modules. |
| 21 | RA3/AN3/VREF+ | bidirectional | Digital I/O (PORTA<3>), analog input 3, or A/D high reference voltage input (VREF+). |
| 22 | RA2/AN2/VREF- | bidirectional | Digital I/O (PORTA<2>), analog input 2, or A/D low reference voltage input (VREF-). |
| 23 | RA1/AN1 | bidirectional | Digital I/O (PORTA<1>) or analog input 1. |
| 24 | RA0/AN0 | bidirectional | Digital I/O (PORTA<0>) or analog input 0. |
| 25 | VSS | power_in | Ground reference for logic and I/O pins. |
| 26 | VDD | power_in | Positive supply for logic and I/O pins. |
| 27 | RA5/AN4 | bidirectional | Digital I/O (PORTA<5>) or analog input 4. |
| 28 | RA4/T0CKI | bidirectional | Digital I/O (PORTA<4>), open-drain when configured as output, or Timer0 external clock input (T0CKI) with Schmitt Trigger input. |
| 29 | RC1/T1OSI/CCP2 | bidirectional | Digital I/O (PORTC<1>), Timer1 oscillator input (T1OSI), or CCP2 capture input / compare and PWM output (default CCP2 assignment when CCP2MX is set). |
| 30 | RC0/T1OSO/T13CKI | bidirectional | Digital I/O (PORTC<0>), Timer1 oscillator output (T1OSO), or Timer1/Timer3 external clock input (T13CKI). |
| 31 | RC6/TX1/CK1 | bidirectional | Digital I/O (PORTC<6>), EUSART asynchronous transmit (TX1), or EUSART synchronous clock (CK1). |
| 32 | RC7/RX1/DT1 | bidirectional | Digital I/O (PORTC<7>), EUSART asynchronous receive (RX1), or EUSART synchronous data (DT1). |
| 33 | RC2/CCP1 | bidirectional | Digital I/O (PORTC<2>), or CCP1 capture input / compare output / PWM output. |
| 34 | RC3/SCK/SCL | bidirectional | Digital I/O (PORTC<3>), MSSP SPI clock input/output (SCK), or I2C clock input/output (SCL). |
| 35 | RC4/SDI/SDA | bidirectional | Digital I/O (PORTC<4>), MSSP SPI data input (SDI), or I2C data I/O (SDA). |
| 36 | RC5/SDO | bidirectional | Digital I/O (PORTC<5>) or MSSP SPI data output (SDO). |
| 37 | RB7/KBI3/PGD | bidirectional | Digital I/O (PORTB<7>) with weak pull-up, interrupt-on-change pin (KBI3), or ICSP/ICD serial data pin (PGD). |
| 38 | VDD | power_in | Positive supply for logic and I/O pins. |
| 39 | RA7/OSC1/CLKI | bidirectional | General purpose I/O pin RA7, or oscillator crystal input / external clock source input (OSC1/CLKI); RA7 is only available as digital I/O in select oscillator modes. |
| 40 | RA6/OSC2/CLKO | bidirectional | General purpose I/O pin RA6, or oscillator crystal output (OSC2) or CLKO at 1/4 the OSC1 frequency in EC modes; RA6 is only available as digital I/O in select oscillator modes. |
| 41 | VSS | power_in | Ground reference for logic and I/O pins. |
| 42 | RB6/KBI2/PGC | bidirectional | Digital I/O (PORTB<6>) with weak pull-up, interrupt-on-change pin (KBI2), or ICSP/ICD clock pin (PGC). |
| 43 | RB5/KBI1 | bidirectional | Digital I/O (PORTB<5>) with weak pull-up, or interrupt-on-change pin (KBI1). |
| 44 | RB4/KBI0 | bidirectional | Digital I/O (PORTB<4>) with weak pull-up, or interrupt-on-change pin (KBI0). |
| 45 | RB3/INT3 | bidirectional | Digital I/O (PORTB<3>) with weak pull-up, or external interrupt 3 input (INT3). |
| 46 | RB2/INT2 | bidirectional | Digital I/O (PORTB<2>) with weak pull-up, or external interrupt 2 input (INT2). |
| 47 | RB1/INT1 | bidirectional | Digital I/O (PORTB<1>) with weak pull-up, or external interrupt 1 input (INT1). |
| 48 | RB0/INT0 | bidirectional | Digital I/O (PORTB<0>) with weak pull-up, or external interrupt 0 input (INT0). |
| 49 | RD7/PSP7 | bidirectional | Digital I/O (PORTD<7>) or Parallel Slave Port data bit 7 (PSP7). |
| 50 | RD6/PSP6 | bidirectional | Digital I/O (PORTD<6>) or Parallel Slave Port data bit 6 (PSP6). |
| 51 | RD5/PSP5 | bidirectional | Digital I/O (PORTD<5>) or Parallel Slave Port data bit 5 (PSP5). |
| 52 | RD4/PSP4 | bidirectional | Digital I/O (PORTD<4>) or Parallel Slave Port data bit 4 (PSP4). |
| 53 | RD3/PSP3 | bidirectional | Digital I/O (PORTD<3>) or Parallel Slave Port data bit 3 (PSP3). |
| 54 | RD2/PSP2 | bidirectional | Digital I/O (PORTD<2>) or Parallel Slave Port data bit 2 (PSP2). |
| 55 | RD1/PSP1 | bidirectional | Digital I/O (PORTD<1>) or Parallel Slave Port data bit 1 (PSP1). |
| 56 | VSS | power_in | Ground reference for logic and I/O pins. |
| 57 | VDD | power_in | Positive supply for logic and I/O pins. |
| 58 | RD0/PSP0 | bidirectional | Digital I/O (PORTD<0>) or Parallel Slave Port data bit 0 (PSP0). |
| 59 | RE7/CCP2 | bidirectional | Digital I/O (PORTE<7>) or alternate CCP2 capture input / compare and PWM output, selected when the CCP2MX Configuration bit is cleared. |
| 60 | RE6 | bidirectional | Digital I/O (PORTE<6>), with input tolerance limited to VDD. |
| 61 | RE5 | bidirectional | Digital I/O (PORTE<5>), with input tolerance limited to VDD. |
| 62 | RE4 | bidirectional | Digital I/O (PORTE<4>), with input tolerance limited to VDD. |
| 63 | RE3 | bidirectional | Digital I/O (PORTE<3>), with input tolerance limited to VDD. |
| 64 | RE2/CS | bidirectional | Digital I/O (PORTE<2>) or Parallel Slave Port chip select control input (CS), with input tolerance limited to VDD. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TQFP-64(10x10) |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 64 |
CAD (KiCad official)
- Symbol:
PIC18F65J11-I - Footprint:
Package_QFP:TQFP-64_10x10mm_P0.5mm - 3D model: TQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
pic18f65j11-i-etched.step/pic18f65j11-i-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pic18f65j11-i.step/pic18f65j11-i.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (408 pp, sha256
7edd0fa5dc6a1855, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).