Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MP2325GJ-Z

Monolithic Power Systems · DC-DC Converters · TSOT-23-8

MP2325GJ-Z from Monolithic Power Systems, in a TSOT-23-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, read twice and the reads agreed). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 PG output Open-drain power good output that is pulled up by an external resistor when the output voltage exceeds 90% of nominal, with a 40μs delay from FB≥90% to PG going high.
2 IN power_in Supply voltage input for the internal MOSFETs and regulator, operating from 4.5V to 24V and requiring a low-ESR, low-inductance decoupling capacitor placed very close to the pin.
3 SW output Switch output connected to the inductor and bootstrap capacitor, driven up to VIN by the high-side switch during PWM on time and pulled negative by inductor current during off time.
4 GND power_in System ground and reference ground of the regulated output voltage, to be connected to GND copper with vias with careful PCB layout.
5 BST passive Bootstrap pin requiring a capacitor and a 20Ω resistor between SW and BST to form a floating supply across the high-side switch driver.
6 EN/SYNC input Enable input (EN=1 enables) that also accepts an external clock from 200kHz to 2MHz for frequency sync, with a 100kΩ resistor to VIN for automatic start-up.
7 VCC power_out Internal bias supply output to be decoupled with 0.1μF-0.22μF, with capacitance no more than 0.22μF.
8 FB input Feedback input from an external resistor divider from the output to GND that sets the output voltage, with frequency fold-back when FB is below 400mV.

Key specifications

Parameter Value
Manufacturer Monolithic Power Systems
Package TSOT-23-8
Category Power Management (PMIC)
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Current (Quiescent) Iq 130 180 240 μA VEN = 2V, VFB = 1V 3
Current Limit ILIMIT 4.5 5.5 6.5 A Duty Cycle=40% 3
Oscillator Frequency fSW 420 500 620 kHz VFB=750mV 3
Maximum Duty Cycle DMAX 90 95 % VFB=750mV 3
Sync Frequency Range fSYNC 0.2 2 MHz 3
Feedback Voltage VFB 783 791 799 mV TA=25ºC 3
Feedback Current IFB 10 50 nA VFB=820mV 3
EN Rising Threshold VEN_RISING 1.2 1.4 1.6 V 3
EN Hysteresis VEN_HYS 80 150 220 mV 3
EN Input Current IEN 1.5 2 2.5 μA VEN=2V 3
EN Input Current IEN 0 50 nA VEN=0 3
EN Turn Off Delay ENTd-off 6 10 14 μs 3
Power Good Sink Voltage VPG 0.4 V Sink 1mA 3
Power Good Leakage Current IPG-LEAK 1 μA 3
VIN UVLO Threshold-Rising INUVVth 3.7 3.9 4.1 V 3
VIN UVLO Threshold-Hysteresis INUVHYS 550 650 750 mV 3
VCC Regulator VCC 4.65 4.9 5.15 V 3
VCC Load Regulation 0 1 3 % ICC=5mA 3
Soft-Start Period TSS 0.8 1.5 2.2 ms 3
Switch Leakage SWLKG 1 μA VEN = 0V, VSW =12V 3
Supply Current (Shutdown) IIN 5.5 μA VEN = 0V 3
HS Switch On Resistance HSRDS-ON 90 mΩ VBST-SW=5V 3
LS Switch On Resistance LSRDS-ON 40 mΩ VCC=5V 3
Fold-back Frequency fFB 0.5 fSW VFB=200mV 3
Minimum On Time TON_MIN 60 ns Guaranteed by design 3
Power Good Rising Threshold PGVTH-Hi 0.9 VFB 3
Power Good Falling Threshold PGVTH-LO 0.85 VFB 3
Power Good Delay PGTd 40 μs 3
Thermal Shutdown 150 ºC Guaranteed by design 3
Thermal Hysteresis 20 ºC Guaranteed by design 3
Input Voltage (absolute max) VIN -0.3 28 V 2
Switch Voltage (absolute max) VSW -0.3 28 V 2
Bootstrap Voltage (absolute max) VBST 6 V VSW+6V 2
All Other Pins (absolute max) -0.3 6 V 2
Continuous Power Dissipation PD 1.25 W TA=+25°C 2
Junction Temperature TJ 150 °C 2
Lead Temperature 260 °C 2
Storage Temperature -65 150 °C 2
Supply Voltage VIN 4.5 24 V 2
Output Voltage VOUT 0.8 V 0.8V to VIN*DMAX 2
Operating Junction Temperature TJ -40 125 °C 2

CAD (KiCad official)

  • Symbol: MP2325GJ-Z
  • Footprint: Package_TO_SOT_SMD:TSOT-23-8
  • 3D model: TSOT-23-8 (KiCad packages3D, STEP)
  • 3D model files: mp2325gj-z-etched.step / mp2325gj-z-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mp2325gj-z.step / mp2325gj-z.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Monolithic Power Systems datasheet, copy hosted by LCSC (16 pp, sha256 e0e7c2448bb3ad8c, retrieved 2026-11-20)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF