3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMP2325GJ-Z
Monolithic Power Systems · DC-DC Converters · TSOT-23-8
MP2325GJ-Z from Monolithic Power Systems, in a TSOT-23-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, read twice and the reads agreed). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PG | output | Open-drain power good output that is pulled up by an external resistor when the output voltage exceeds 90% of nominal, with a 40μs delay from FB≥90% to PG going high. |
| 2 | IN | power_in | Supply voltage input for the internal MOSFETs and regulator, operating from 4.5V to 24V and requiring a low-ESR, low-inductance decoupling capacitor placed very close to the pin. |
| 3 | SW | output | Switch output connected to the inductor and bootstrap capacitor, driven up to VIN by the high-side switch during PWM on time and pulled negative by inductor current during off time. |
| 4 | GND | power_in | System ground and reference ground of the regulated output voltage, to be connected to GND copper with vias with careful PCB layout. |
| 5 | BST | passive | Bootstrap pin requiring a capacitor and a 20Ω resistor between SW and BST to form a floating supply across the high-side switch driver. |
| 6 | EN/SYNC | input | Enable input (EN=1 enables) that also accepts an external clock from 200kHz to 2MHz for frequency sync, with a 100kΩ resistor to VIN for automatic start-up. |
| 7 | VCC | power_out | Internal bias supply output to be decoupled with 0.1μF-0.22μF, with capacitance no more than 0.22μF. |
| 8 | FB | input | Feedback input from an external resistor divider from the output to GND that sets the output voltage, with frequency fold-back when FB is below 400mV. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | TSOT-23-8 |
| Category | Power Management (PMIC) |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Current (Quiescent) | Iq | 130 | 180 | 240 | μA | VEN = 2V, VFB = 1V | 3 |
| Current Limit | ILIMIT | 4.5 | 5.5 | 6.5 | A | Duty Cycle=40% | 3 |
| Oscillator Frequency | fSW | 420 | 500 | 620 | kHz | VFB=750mV | 3 |
| Maximum Duty Cycle | DMAX | 90 | 95 | % | VFB=750mV | 3 | |
| Sync Frequency Range | fSYNC | 0.2 | 2 | MHz | 3 | ||
| Feedback Voltage | VFB | 783 | 791 | 799 | mV | TA=25ºC | 3 |
| Feedback Current | IFB | 10 | 50 | nA | VFB=820mV | 3 | |
| EN Rising Threshold | VEN_RISING | 1.2 | 1.4 | 1.6 | V | 3 | |
| EN Hysteresis | VEN_HYS | 80 | 150 | 220 | mV | 3 | |
| EN Input Current | IEN | 1.5 | 2 | 2.5 | μA | VEN=2V | 3 |
| EN Input Current | IEN | 0 | 50 | nA | VEN=0 | 3 | |
| EN Turn Off Delay | ENTd-off | 6 | 10 | 14 | μs | 3 | |
| Power Good Sink Voltage | VPG | 0.4 | V | Sink 1mA | 3 | ||
| Power Good Leakage Current | IPG-LEAK | 1 | μA | 3 | |||
| VIN UVLO Threshold-Rising | INUVVth | 3.7 | 3.9 | 4.1 | V | 3 | |
| VIN UVLO Threshold-Hysteresis | INUVHYS | 550 | 650 | 750 | mV | 3 | |
| VCC Regulator | VCC | 4.65 | 4.9 | 5.15 | V | 3 | |
| VCC Load Regulation | 0 | 1 | 3 | % | ICC=5mA | 3 | |
| Soft-Start Period | TSS | 0.8 | 1.5 | 2.2 | ms | 3 | |
| Switch Leakage | SWLKG | 1 | μA | VEN = 0V, VSW =12V | 3 | ||
| Supply Current (Shutdown) | IIN | 5.5 | μA | VEN = 0V | 3 | ||
| HS Switch On Resistance | HSRDS-ON | 90 | mΩ | VBST-SW=5V | 3 | ||
| LS Switch On Resistance | LSRDS-ON | 40 | mΩ | VCC=5V | 3 | ||
| Fold-back Frequency | fFB | 0.5 | fSW | VFB=200mV | 3 | ||
| Minimum On Time | TON_MIN | 60 | ns | Guaranteed by design | 3 | ||
| Power Good Rising Threshold | PGVTH-Hi | 0.9 | VFB | 3 | |||
| Power Good Falling Threshold | PGVTH-LO | 0.85 | VFB | 3 | |||
| Power Good Delay | PGTd | 40 | μs | 3 | |||
| Thermal Shutdown | 150 | ºC | Guaranteed by design | 3 | |||
| Thermal Hysteresis | 20 | ºC | Guaranteed by design | 3 | |||
| Input Voltage (absolute max) | VIN | -0.3 | 28 | V | 2 | ||
| Switch Voltage (absolute max) | VSW | -0.3 | 28 | V | 2 | ||
| Bootstrap Voltage (absolute max) | VBST | 6 | V | VSW+6V | 2 | ||
| All Other Pins (absolute max) | -0.3 | 6 | V | 2 | |||
| Continuous Power Dissipation | PD | 1.25 | W | TA=+25°C | 2 | ||
| Junction Temperature | TJ | 150 | °C | 2 | |||
| Lead Temperature | 260 | °C | 2 | ||||
| Storage Temperature | -65 | 150 | °C | 2 | |||
| Supply Voltage | VIN | 4.5 | 24 | V | 2 | ||
| Output Voltage | VOUT | 0.8 | V | 0.8V to VIN*DMAX | 2 | ||
| Operating Junction Temperature | TJ | -40 | 125 | °C | 2 |
CAD (KiCad official)
- Symbol:
MP2325GJ-Z - Footprint:
Package_TO_SOT_SMD:TSOT-23-8 - 3D model: TSOT-23-8 (KiCad packages3D, STEP)
- 3D model files:
mp2325gj-z-etched.step/mp2325gj-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mp2325gj-z.step/mp2325gj-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet, copy hosted by LCSC (16 pp, sha256
e0e7c2448bb3ad8c, retrieved 2026-11-20) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).