Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

L297

STMicroelectronics · Stepper Motor Driver · DIP-20

L297 from STMicroelectronics, in a DIP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SYNC bidirectional Output of the on-chip chopper oscillator, with SYNC pins of synchronized L297s connected together, and an external clock source injected at this terminal if used.
2 GND power_in Ground connection.
3 HOME output Open collector output that opens the transistor when active to indicate the initial translator state (ABCD = 0101).
4 A output Motor phase A drive signal for the power stage.
5 ~{INH1} input Active low inhibit control for the driver stage of phases A and B, also used by the chopper to regulate load current when CONTROL is low.
6 B output Motor phase B drive signal for the power stage.
7 C output Motor phase C drive signal for the power stage.
8 ~{INH2} input Active low inhibit control for the drive stages of phases C and D, with the same functions as INH1.
9 D output Motor phase D drive signal for the power stage.
10 ENABLE input Chip enable input; when low, INH1, INH2, A, B, C and D are brought low.
11 CONTROL input Control input that selects chopper action: when low the chopper acts on INH1 and INH2, and when high it acts on phase lines ABCD.
12 Vs power_in 5V supply input; the electrical characteristics specify Vs from 4.75 V to 7 V.
13 SENS2 input Input for the load current sense voltage from the power stages of phases C and D.
14 SENS1 input Input for the load current sense voltage from the power stages of phases A and B.
15 Vref power_in Reference voltage for the chopper circuit that determines the peak load current, specified over a 0 to 3 V range.
16 OSC passive RC network (R to VCC, C to ground) sets the chopper rate with f ≅ 1/0.69RC, and this pin is grounded on all but one device in synchronized configurations.
17 CW/~{CCW} input Clockwise/counterclockwise direction control input that is synchronized internally so direction can change at any time.
18 ~{CLOCK} input Step clock input where the motor advances one increment on the rising edge of an active low pulse.
19 HALF/~{FULL} input Half/full step select input; high selects half step operation and low selects full step operation.
20 ~{RESET} input Active low reset input that restores the translator to the home position (state 1, ABCD = 0101).

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package DIP-20
Category Motor Driver ICs
Pins 20

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage Vs 10 V 1
Input signals Vi 7 V 1
Total power dissipation Ptot 1 W Tamb = 70°C 1
Storage and junction temperature Tstg, Tj -40 150 °C 1
Thermal resistance junction-ambient (DIP20) Rth-j-amb 80 °C/W 4
Supply voltage (pin 12) Vs 4.75 7 V 6
Quiescent supply current (pin 12) Is 50 80 mA Outputs floating 6
Input voltage low (pins 11, 17, 18, 19, 20) Vi 0.6 V 6
Input voltage high (pins 11, 17, 18, 19, 20) Vi 2 V 6
Input current (pins 11, 17, 18, 19, 20) Ii 100 µA Vi = L 6
Input current (pins 11, 17, 18, 19, 20) Ii 10 µA Vi = H 6
Enable input voltage (pin 10) low Ven 1.3 V Low 6
Enable input voltage (pin 10) high Ven 2 V High 6
Enable input current (pin 10) Ien 100 µA Ven = L 6
Enable input current (pin 10) Ien 10 µA Ven = H 6
Phase output voltage (pins 4, 6, 7, 9) low VOL 0.4 V Io = 10mA 6
Phase output voltage (pins 4, 6, 7, 9) high VOH 3.9 V Io = 5mA 6
Inhibit output voltage (pins 5, 8) low Vinh L 0.4 V Io = 10mA 6
Inhibit output voltage (pins 5, 8) high Vinh H 3.9 V Io = 5mA 6
Sync output voltage high VSYNC H 3.3 V Io = 5mA 6
Sync output voltage low VSYNC V 0.8 Io = 5mA 6
Leakage current (pin 3) Ileak 1 µA VCE = 7 V 7
Saturation voltage (pin 3) Vsat 0.4 V I = 5 mA 7
Comparators offset voltage (pins 13, 14, 15) Voff 5 mV Vref = 1 V 7
Comparator bias current (pins 13, 14, 15) Io -100 10 µA 7
Input reference voltage (pin 15) Vref 0 3 V 7
Clock time tCLK 0.5 µs 7
Set up time tS 1 µs 7
Hold time tH 4 µs 7
Reset time tR 1 µs 7
Reset to clock delay tRCLK 1 µs 7

CAD (KiCad official)

  • Symbol: L297
  • Footprint: Package_DIP:DIP-20_W7.62mm
  • 3D model: DIP-20 (KiCad packages3D, STEP)
  • 3D model files: l297-1-etched.step / l297-1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); l297-1.step / l297-1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (11 pp, sha256 49b6f5cd43ebfcb6, retrieved 2026-11-12, tier: manufacturer)
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF