Generated by kicad-footprint-generator · KiCad file format 20260206
L297
STMicroelectronics · Stepper Motor Driver · DIP-20
L297 from STMicroelectronics, in a DIP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SYNC | bidirectional | Output of the on-chip chopper oscillator, with SYNC pins of synchronized L297s connected together, and an external clock source injected at this terminal if used. |
| 2 | GND | power_in | Ground connection. |
| 3 | HOME | output | Open collector output that opens the transistor when active to indicate the initial translator state (ABCD = 0101). |
| 4 | A | output | Motor phase A drive signal for the power stage. |
| 5 | ~{INH1} | input | Active low inhibit control for the driver stage of phases A and B, also used by the chopper to regulate load current when CONTROL is low. |
| 6 | B | output | Motor phase B drive signal for the power stage. |
| 7 | C | output | Motor phase C drive signal for the power stage. |
| 8 | ~{INH2} | input | Active low inhibit control for the drive stages of phases C and D, with the same functions as INH1. |
| 9 | D | output | Motor phase D drive signal for the power stage. |
| 10 | ENABLE | input | Chip enable input; when low, INH1, INH2, A, B, C and D are brought low. |
| 11 | CONTROL | input | Control input that selects chopper action: when low the chopper acts on INH1 and INH2, and when high it acts on phase lines ABCD. |
| 12 | Vs | power_in | 5V supply input; the electrical characteristics specify Vs from 4.75 V to 7 V. |
| 13 | SENS2 | input | Input for the load current sense voltage from the power stages of phases C and D. |
| 14 | SENS1 | input | Input for the load current sense voltage from the power stages of phases A and B. |
| 15 | Vref | power_in | Reference voltage for the chopper circuit that determines the peak load current, specified over a 0 to 3 V range. |
| 16 | OSC | passive | RC network (R to VCC, C to ground) sets the chopper rate with f ≅ 1/0.69RC, and this pin is grounded on all but one device in synchronized configurations. |
| 17 | CW/~{CCW} | input | Clockwise/counterclockwise direction control input that is synchronized internally so direction can change at any time. |
| 18 | ~{CLOCK} | input | Step clock input where the motor advances one increment on the rising edge of an active low pulse. |
| 19 | HALF/~{FULL} | input | Half/full step select input; high selects half step operation and low selects full step operation. |
| 20 | ~{RESET} | input | Active low reset input that restores the translator to the home position (state 1, ABCD = 0101). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | DIP-20 |
| Category | Motor Driver ICs |
| Pins | 20 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | Vs | 10 | V | 1 | |||
| Input signals | Vi | 7 | V | 1 | |||
| Total power dissipation | Ptot | 1 | W | Tamb = 70°C | 1 | ||
| Storage and junction temperature | Tstg, Tj | -40 | 150 | °C | 1 | ||
| Thermal resistance junction-ambient (DIP20) | Rth-j-amb | 80 | °C/W | 4 | |||
| Supply voltage (pin 12) | Vs | 4.75 | 7 | V | 6 | ||
| Quiescent supply current (pin 12) | Is | 50 | 80 | mA | Outputs floating | 6 | |
| Input voltage low (pins 11, 17, 18, 19, 20) | Vi | 0.6 | V | 6 | |||
| Input voltage high (pins 11, 17, 18, 19, 20) | Vi | 2 | V | 6 | |||
| Input current (pins 11, 17, 18, 19, 20) | Ii | 100 | µA | Vi = L | 6 | ||
| Input current (pins 11, 17, 18, 19, 20) | Ii | 10 | µA | Vi = H | 6 | ||
| Enable input voltage (pin 10) low | Ven | 1.3 | V | Low | 6 | ||
| Enable input voltage (pin 10) high | Ven | 2 | V | High | 6 | ||
| Enable input current (pin 10) | Ien | 100 | µA | Ven = L | 6 | ||
| Enable input current (pin 10) | Ien | 10 | µA | Ven = H | 6 | ||
| Phase output voltage (pins 4, 6, 7, 9) low | VOL | 0.4 | V | Io = 10mA | 6 | ||
| Phase output voltage (pins 4, 6, 7, 9) high | VOH | 3.9 | V | Io = 5mA | 6 | ||
| Inhibit output voltage (pins 5, 8) low | Vinh L | 0.4 | V | Io = 10mA | 6 | ||
| Inhibit output voltage (pins 5, 8) high | Vinh H | 3.9 | V | Io = 5mA | 6 | ||
| Sync output voltage high | VSYNC H | 3.3 | V | Io = 5mA | 6 | ||
| Sync output voltage low | VSYNC V | 0.8 | Io = 5mA | 6 | |||
| Leakage current (pin 3) | Ileak | 1 | µA | VCE = 7 V | 7 | ||
| Saturation voltage (pin 3) | Vsat | 0.4 | V | I = 5 mA | 7 | ||
| Comparators offset voltage (pins 13, 14, 15) | Voff | 5 | mV | Vref = 1 V | 7 | ||
| Comparator bias current (pins 13, 14, 15) | Io | -100 | 10 | µA | 7 | ||
| Input reference voltage (pin 15) | Vref | 0 | 3 | V | 7 | ||
| Clock time | tCLK | 0.5 | µs | 7 | |||
| Set up time | tS | 1 | µs | 7 | |||
| Hold time | tH | 4 | µs | 7 | |||
| Reset time | tR | 1 | µs | 7 | |||
| Reset to clock delay | tRCLK | 1 | µs | 7 |
CAD (KiCad official)
- Symbol:
L297 - Footprint:
Package_DIP:DIP-20_W7.62mm - 3D model: DIP-20 (KiCad packages3D, STEP)
- 3D model files:
l297-1-etched.step/l297-1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);l297-1.step/l297-1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (11 pp, sha256
49b6f5cd43ebfcb6, retrieved 2026-11-12, tier: manufacturer) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).