Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TPS74501PDRVT

Texas Instruments · Linear Voltage Regulators (LDO) · WSON-6(2x2)

TPS74501PDRVT from Texas Instruments, in a WSON-6(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 OUT power_out Regulated output voltage pin; a capacitor (recommended 1 µF to 220 µF, minimum derated 0.47 µF) is required from OUT to ground for stability.
2 FB input Input to the control loop error amplifier used to set the LDO output voltage (0.55 V to 5.5 V adjustable range); absolute maximum -0.3 V to 2 V.
3 GND power_in Ground pin.
4 EN input Enable pin; drive above VEN(HI) to turn on the regulator and below VEN(LO) to put the LDO into shutdown mode, with a 0 V to 6.0 V recommended range.
5 PG output Open-drain power-good output that monitors the feedback pin voltage to indicate output status, with 0 V to 6.0 V recommended PG voltage and ±10 mA maximum current.
6 IN power_in Input supply pin with 1.5 V to 6.0 V recommended range; use a 1 µF or larger ceramic capacitor close to the device.
7 Thermal pad passive Connect the thermal pad to a large area GND plane for improved thermal performance.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WSON-6(2x2)
Category Power Supply Chip
Pins 7

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage VIN 1.5 6 V 4
Output voltage VOUT 0.55 5.5 V 4
Output current IOUT 0 500 mA 4
Input capacitor CIN 1 µF 4
Output capacitor COUT 1 220 µF Minimum derated capacitance of 0.47 µF is required for stability 4
Enable voltage VEN 0 6 V 4
Enable toggle frequency fEN 10 kHz 4
PG voltage VPG 0 6 V 4
Junction temperature TJ -40 125 °C 4
Supply voltage VIN -0.3 6.5 V 4
Enable voltage VEN -0.3 6.5 V 4
Feedback voltage VFB -0.3 2 V 4
Power-good voltage VPG -0.3 6.5 V 4
Output voltage VOUT -0.3 6.5 V VIN + 0.3 V or 6.5 V, whichever is smaller 4
Power-good current -10 10 mA 4
Operating junction temperature TJ -40 150 °C 4
Storage temperature Tstg -65 150 °C 4
ESD HBM V(ESD) -2000 2000 V Human-body model per ANSI/ESDA/JEDEC JS-001 4
ESD CDM V(ESD) -500 500 V Charged-device model per JESD22-C101 4
Junction-to-ambient thermal resistance RθJA 80.3 °C/W DRV (WSON) 6 pins 5
Junction-to-case (top) thermal resistance RθJC(top) 98.7 °C/W 5
Junction-to-board thermal resistance RθJB 44.8 °C/W 5
Junction-to-case (bottom) thermal resistance RθJC(bot) 20.8 °C/W 5
Feedback voltage VFB 0.55 V TJ = 25°C 5
Output accuracy -0.7 0.7 % TJ = 25°C 5
Output accuracy -1 1 % -40°C ≤ TJ ≤ +85°C 5
Output accuracy -1.5 1.5 % -40°C ≤ TJ ≤ +125°C 5
Line regulation 2 7.5 mV VOUT(NOM) + 0.5 V ≤ VIN ≤ 6.0 V 5
Load regulation 0.03 V/A 0.1 mA ≤ IOUT ≤ 500 mA, VIN ≥ 2.0 V 5
Ground current IGND 10 25 31 µA IOUT = 0 mA, TJ = 25°C 5
Ground current IGND 35 µA IOUT = 0 mA, -40°C ≤ TJ ≤ +125°C 5
Shutdown current ISHDN 0.1 1 µA VEN ≤ 0.3 V, 1.5 V ≤ VIN ≤ 6.0 V 5
Feedback pin current IFB 0.01 0.1 µA 5
Output current limit ICL 530 720 865 mA VIN = VOUT(NOM) + 1.0 V, VOUT = VOUT(NOM), 0.2 V, VOUT < 1.5 V 5
Short-circuit current limit ISC 350 mA VIN = VOUT(NOM) + 1.0 V, VOUT = 0 V 5
Dropout voltage VDO 720 880 mV IOUT = 500 mA, 0.65 V ≤ VOUT < 0.8 V 5
Dropout voltage VDO 585 750 mV IOUT = 500 mA, 0.8 V ≤ VOUT < 1.0 V 5
Dropout voltage VDO 420 570 mV IOUT = 500 mA, 1.0 V ≤ VOUT < 1.2 V 5
Dropout voltage VDO 285 400 mV IOUT = 500 mA, 1.2 V ≤ VOUT < 1.5 V 5
Dropout voltage VDO 180 235 mV IOUT = 500 mA, 1.5 V ≤ VOUT < 1.8 V 5
Dropout voltage VDO 140 185 mV IOUT = 500 mA, 1.8 V ≤ VOUT < 2.5 V 5
Dropout voltage VDO 102 140 mV IOUT = 500 mA, 2.5 V ≤ VOUT < 3.3 V 5
Dropout voltage VDO 95 130 mV IOUT = 500 mA, 3.3 V ≤ VOUT ≤ 5.5 V 5
Undervoltage lockout rising VUVLO 1.21 1.33 1.47 V VIN rising 5
Undervoltage lockout falling VUVLO 1.17 1.29 1.42 V VIN falling 5
Startup time tSTR 500 µs From EN low-to-high transition to VOUT = VOUT(NOM) × 95% 5
EN pin high voltage VEN(HI) 1 V 6
EN pin low voltage VEN(LO) 0.3 V 6
PG high threshold PGHTH 89 94 95 %VOUT VOUT increasing 6
PG low threshold PGLTH 87 92 93 %VOUT VOUT decreasing 6
PG pin low-level output voltage VOL(PG) 300 mV VIN ≥ 1.5 V, ISINK = 1 mA 6
PG pin leakage current Ilkg(PG) 300 nA VOUT > PGHTH, VPG = 6.0 V 6
PG delay time rising tPGDH 135 165 178 µs Time from 92% VOUT to 20% of PG 6
PG delay time falling tPGDL 1.5 7 10 µs Time from 90% VOUT to 80% of PG 6

CAD (KiCad official)

  • Symbol: TPS74501PDRVT
  • Footprint: Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm
  • 3D model: WSON-6(2x2) (KiCad packages3D, STEP)
  • 3D model files: tps74501pdrvt-etched.step / tps74501pdrvt-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps74501pdrvt.step / tps74501pdrvt.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (34 pp, sha256 8ad57af9888e85bc, retrieved 2026-10-26, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF