3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTPS74501PDRVT
Texas Instruments · Linear Voltage Regulators (LDO) · WSON-6(2x2)
TPS74501PDRVT from Texas Instruments, in a WSON-6(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | power_out | Regulated output voltage pin; a capacitor (recommended 1 µF to 220 µF, minimum derated 0.47 µF) is required from OUT to ground for stability. |
| 2 | FB | input | Input to the control loop error amplifier used to set the LDO output voltage (0.55 V to 5.5 V adjustable range); absolute maximum -0.3 V to 2 V. |
| 3 | GND | power_in | Ground pin. |
| 4 | EN | input | Enable pin; drive above VEN(HI) to turn on the regulator and below VEN(LO) to put the LDO into shutdown mode, with a 0 V to 6.0 V recommended range. |
| 5 | PG | output | Open-drain power-good output that monitors the feedback pin voltage to indicate output status, with 0 V to 6.0 V recommended PG voltage and ±10 mA maximum current. |
| 6 | IN | power_in | Input supply pin with 1.5 V to 6.0 V recommended range; use a 1 µF or larger ceramic capacitor close to the device. |
| 7 | Thermal pad | passive | Connect the thermal pad to a large area GND plane for improved thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WSON-6(2x2) |
| Category | Power Supply Chip |
| Pins | 7 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage | VIN | 1.5 | 6 | V | 4 | ||
| Output voltage | VOUT | 0.55 | 5.5 | V | 4 | ||
| Output current | IOUT | 0 | 500 | mA | 4 | ||
| Input capacitor | CIN | 1 | µF | 4 | |||
| Output capacitor | COUT | 1 | 220 | µF | Minimum derated capacitance of 0.47 µF is required for stability | 4 | |
| Enable voltage | VEN | 0 | 6 | V | 4 | ||
| Enable toggle frequency | fEN | 10 | kHz | 4 | |||
| PG voltage | VPG | 0 | 6 | V | 4 | ||
| Junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Supply voltage | VIN | -0.3 | 6.5 | V | 4 | ||
| Enable voltage | VEN | -0.3 | 6.5 | V | 4 | ||
| Feedback voltage | VFB | -0.3 | 2 | V | 4 | ||
| Power-good voltage | VPG | -0.3 | 6.5 | V | 4 | ||
| Output voltage | VOUT | -0.3 | 6.5 | V | VIN + 0.3 V or 6.5 V, whichever is smaller | 4 | |
| Power-good current | -10 | 10 | mA | 4 | |||
| Operating junction temperature | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| ESD HBM | V(ESD) | -2000 | 2000 | V | Human-body model per ANSI/ESDA/JEDEC JS-001 | 4 | |
| ESD CDM | V(ESD) | -500 | 500 | V | Charged-device model per JESD22-C101 | 4 | |
| Junction-to-ambient thermal resistance | RθJA | 80.3 | °C/W | DRV (WSON) 6 pins | 5 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 98.7 | °C/W | 5 | |||
| Junction-to-board thermal resistance | RθJB | 44.8 | °C/W | 5 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 20.8 | °C/W | 5 | |||
| Feedback voltage | VFB | 0.55 | V | TJ = 25°C | 5 | ||
| Output accuracy | -0.7 | 0.7 | % | TJ = 25°C | 5 | ||
| Output accuracy | -1 | 1 | % | -40°C ≤ TJ ≤ +85°C | 5 | ||
| Output accuracy | -1.5 | 1.5 | % | -40°C ≤ TJ ≤ +125°C | 5 | ||
| Line regulation | 2 | 7.5 | mV | VOUT(NOM) + 0.5 V ≤ VIN ≤ 6.0 V | 5 | ||
| Load regulation | 0.03 | V/A | 0.1 mA ≤ IOUT ≤ 500 mA, VIN ≥ 2.0 V | 5 | |||
| Ground current | IGND | 10 | 25 | 31 | µA | IOUT = 0 mA, TJ = 25°C | 5 |
| Ground current | IGND | 35 | µA | IOUT = 0 mA, -40°C ≤ TJ ≤ +125°C | 5 | ||
| Shutdown current | ISHDN | 0.1 | 1 | µA | VEN ≤ 0.3 V, 1.5 V ≤ VIN ≤ 6.0 V | 5 | |
| Feedback pin current | IFB | 0.01 | 0.1 | µA | 5 | ||
| Output current limit | ICL | 530 | 720 | 865 | mA | VIN = VOUT(NOM) + 1.0 V, VOUT = VOUT(NOM), 0.2 V, VOUT < 1.5 V | 5 |
| Short-circuit current limit | ISC | 350 | mA | VIN = VOUT(NOM) + 1.0 V, VOUT = 0 V | 5 | ||
| Dropout voltage | VDO | 720 | 880 | mV | IOUT = 500 mA, 0.65 V ≤ VOUT < 0.8 V | 5 | |
| Dropout voltage | VDO | 585 | 750 | mV | IOUT = 500 mA, 0.8 V ≤ VOUT < 1.0 V | 5 | |
| Dropout voltage | VDO | 420 | 570 | mV | IOUT = 500 mA, 1.0 V ≤ VOUT < 1.2 V | 5 | |
| Dropout voltage | VDO | 285 | 400 | mV | IOUT = 500 mA, 1.2 V ≤ VOUT < 1.5 V | 5 | |
| Dropout voltage | VDO | 180 | 235 | mV | IOUT = 500 mA, 1.5 V ≤ VOUT < 1.8 V | 5 | |
| Dropout voltage | VDO | 140 | 185 | mV | IOUT = 500 mA, 1.8 V ≤ VOUT < 2.5 V | 5 | |
| Dropout voltage | VDO | 102 | 140 | mV | IOUT = 500 mA, 2.5 V ≤ VOUT < 3.3 V | 5 | |
| Dropout voltage | VDO | 95 | 130 | mV | IOUT = 500 mA, 3.3 V ≤ VOUT ≤ 5.5 V | 5 | |
| Undervoltage lockout rising | VUVLO | 1.21 | 1.33 | 1.47 | V | VIN rising | 5 |
| Undervoltage lockout falling | VUVLO | 1.17 | 1.29 | 1.42 | V | VIN falling | 5 |
| Startup time | tSTR | 500 | µs | From EN low-to-high transition to VOUT = VOUT(NOM) × 95% | 5 | ||
| EN pin high voltage | VEN(HI) | 1 | V | 6 | |||
| EN pin low voltage | VEN(LO) | 0.3 | V | 6 | |||
| PG high threshold | PGHTH | 89 | 94 | 95 | %VOUT | VOUT increasing | 6 |
| PG low threshold | PGLTH | 87 | 92 | 93 | %VOUT | VOUT decreasing | 6 |
| PG pin low-level output voltage | VOL(PG) | 300 | mV | VIN ≥ 1.5 V, ISINK = 1 mA | 6 | ||
| PG pin leakage current | Ilkg(PG) | 300 | nA | VOUT > PGHTH, VPG = 6.0 V | 6 | ||
| PG delay time rising | tPGDH | 135 | 165 | 178 | µs | Time from 92% VOUT to 20% of PG | 6 |
| PG delay time falling | tPGDL | 1.5 | 7 | 10 | µs | Time from 90% VOUT to 80% of PG | 6 |
CAD (KiCad official)
- Symbol:
TPS74501PDRVT - Footprint:
Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm - 3D model: WSON-6(2x2) (KiCad packages3D, STEP)
- 3D model files:
tps74501pdrvt-etched.step/tps74501pdrvt-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps74501pdrvt.step/tps74501pdrvt.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (34 pp, sha256
8ad57af9888e85bc, retrieved 2026-10-26, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).