3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownHG24C04CN
HGSEMI · EEPROM · DIP-8
HG24C04CN from HGSEMI, in a DIP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No connect pin; not internally used per the DIP-8/SOP-8/MSOP-8 pin configuration. |
| 2 | E1 | input | Device address input that can be tied to VCC or GND in any combination, and is internally pulled down to GND if left floating. |
| 3 | E2 | input | Device address input that can be tied to VCC or GND in any combination, and is internally pulled down to GND if left floating. |
| 4 | GND | power_in | Ground reference for the power supply, to be connected to system ground. |
| 5 | SDA | bidirectional | Serial data open-drain bidirectional input/output pin used to transfer data to and from the device. |
| 6 | SCL | input | Serial clock input; command and input data on SDA are latched on the rising edge of SCL and output data is clocked out on the falling edge. |
| 7 | WP | input | Write protection input: connected to VCC makes the memory array read-only, connected to GND enables writes, and floating is internally pulled down to GND. |
| 8 | VCC | power_in | Device power supply pin, operating range 1.7V to 5.5V; operation at invalid VCC voltages should not be attempted. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | HGSEMI |
| Package | DIP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Absolute maximum ambient temperature with power applied | TA | -40 | 105 | °C | 18 | ||
| Storage temperature | TSTG | -65 | 150 | °C | 18 | ||
| Supply voltage | VCC | -0.5 | 6 | V | 18 | ||
| Voltage on input pins | VIN | -0.5 | 6 | V | 18 | ||
| Electrostatic pulse (human body model) | VESD | 6000 | V | Human body model | 18 | ||
| Lead temperature (soldering) | TL | 260 | °C | Soldering, 10 seconds | 18 | ||
| Supply voltage | VCC | 1.7 | 5.5 | V | Operating range TA = -40°C to +105°C | 18 | |
| Supply current (Read) | ICC1 | 0.1 | mA | VCC = 1.7V, Read at 1MHz | 18 | ||
| Supply current (Read) | ICC1 | 0.4 | mA | VCC = 5.5V, Read at 400 kHz | 18 | ||
| Supply current (Read) | ICC1 | 0.5 | mA | VCC = 5.5V, Read at 1MHz | 18 | ||
| Supply current (Write) | ICC2 | 1 | mA | VCC = 5.5V, Write at 400 kHz | 18 | ||
| Standby current | ISB | 1 | μA | VCC = 1.7V, VIN = VCC or GND | 18 | ||
| Input leakage current | ILI | 1 | μA | VIN = VCC or GND | 18 | ||
| Output leakage current | ILO | 1 | μA | VOUT = VCC or GND | 18 | ||
| Input low-level voltage (SDA, SCL) | VIL | -0.5 | V | 18 | |||
| Low-level output voltage | VOL1 | 0.4 | V | VCC > 2V, IOL = 3mA | 18 | ||
| Low-level output voltage | VOL2 | 0.2 | V | VCC ≤ 2V, IOL = 2mA | 18 | ||
| Clock frequency, SCL | fSCL | 400 | kHz | Fast mode, VCC = 1.7V to 5.5V | 19 | ||
| Clock frequency, SCL | fSCL | 1000 | kHz | High Speed mode, VCC = 1.7V to 5.5V | 19 | ||
| Clock pulse width low | tLOW | 1300 | ns | Fast mode, VCC = 1.7V to 5.5V | 19 | ||
| Clock pulse width low | tLOW | 600 | ns | High Speed mode, VCC = 1.7V to 5.5V | 19 | ||
| Clock pulse width high | tHIGH | 600 | ns | Fast mode, VCC = 1.7V to 5.5V | 19 | ||
| Clock pulse width high | tHIGH | 260 | ns | High Speed mode, VCC = 1.7V to 5.5V | 19 | ||
| SDA rise time | tR | 300 | ns | Fast mode, VCC = 1.7V to 5.5V; ensured by characterization only (note 1) | 19 | ||
| SDA(Out) fall time | tF | 300 | ns | Fast mode, VCC = 1.7V to 5.5V; ensured by characterization only (note 1) | 19 | ||
| SDA(Out) fall time | tF | 100 | ns | High Speed mode, VCC = 1.7V to 5.5V; ensured by characterization only (note 1) | 19 | ||
| Start hold time | tHD.STA | 600 | ns | Fast mode, VCC = 1.7V to 5.5V | 19 | ||
| Start hold time | tHD.STA | 250 | ns | High Speed mode, VCC = 1.7V to 5.5V | 19 | ||
| Start setup time | tSU.STA | 600 | ns | Fast mode, VCC = 1.7V to 5.5V | 19 | ||
| Start setup time | tSU.STA | 250 | ns | High Speed mode, VCC = 1.7V to 5.5V | 19 | ||
| Stop setup time | tSU.STO | 600 | ns | Fast mode, VCC = 1.7V to 5.5V | 19 | ||
| Stop setup time | tSU.STO | 250 | ns | High Speed mode, VCC = 1.7V to 5.5V | 19 | ||
| Bus free time between Stop and next Start | tBUF | 1300 | ns | Fast mode, VCC = 1.7V to 5.5V | 19 | ||
| Bus free time between Stop and next Start | tBUF | 500 | ns | High Speed mode, VCC = 1.7V to 5.5V | 19 | ||
| Data in hold time | tHD.DI | 0 | ns | Fast mode, VCC = 1.7V to 5.5V | 19 | ||
| Data in setup time | tSU.DAT | 100 | ns | Fast mode, VCC = 1.7V to 5.5V | 19 | ||
| Data in setup time | tSU.DAT | 50 | ns | High Speed mode, VCC = 1.7V to 5.5V | 19 | ||
| Data out hold time | tHD.DAT | 50 | ns | Fast mode, VCC = 1.7V to 5.5V | 19 | ||
| SCL low to data out valid | tAA | 100 | 900 | ns | Fast mode, VCC = 1.7V to 5.5V | 19 | |
| SCL low to data out valid | tAA | 50 | 500 | ns | High Speed mode, VCC = 1.7V to 5.5V | 19 | |
| WP pin setup time | tSU.WP | 1200 | ns | Fast mode, VCC = 1.7V to 5.5V | 19 | ||
| WP pin setup time | tSU.WP | 600 | ns | High Speed mode, VCC = 1.7V to 5.5V | 19 | ||
| WP pin hold time | tHD.WP | 1200 | ns | Fast mode, VCC = 1.7V to 5.5V | 19 | ||
| WP pin hold time | tHD.WP | 600 | ns | High Speed mode, VCC = 1.7V to 5.5V | 19 | ||
| Write cycle time | tWR | 5 | ms | Fast mode, VCC = 1.7V to 5.5V | 19 | ||
| Noise suppression time | tI | 50 | ns | Fast mode, VCC = 1.7V to 5.5V | 19 | ||
| Power-on reset time | tPOR | 10 | ms | 6 | |||
| Power-on reset voltage | VPOR | 1.5 | V | 6 | |||
| Brown-out reset voltage | VBOR | 0.8 | V | 6 | |||
| Time from power-on to first command | tINIT | 10 | ms | 6 | |||
| Warm power cycle off time | tPOFF | 1 | ms | 6 | |||
| Input/output capacitance (SDA) | CI/O | 8 | pF | VI/O = 0V; TA = +25°C, fC = 1MHz | 20 | ||
| Other pins input capacitance | CIN | 6 | pF | VIN = 0V; TA = +25°C, fC = 1MHz | 20 | ||
| Data retention | DR | 200 | year | TA = +25°C | 20 |
CAD (KiCad official)
- Symbol:
HG24C04CN - Footprint:
Package_DIP:DIP-8_W7.62mm - 3D model: DIP-8 (KiCad packages3D, STEP)
- 3D model files:
hg24c04cn-etched.step/hg24c04cn-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);hg24c04cn.step/hg24c04cn.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: HGSEMI datasheet (27 pp, sha256
8bd31d1acd5458af, retrieved 2026-11-04, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text+vision), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).