Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TPS65161PWPR

Texas Instruments · Power Management Specialized - PMIC · HTSSOP-28-EP

TPS65161PWPR from Texas Instruments, in a HTSSOP-28-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 FB input Feedback input of the main boost converter that generates the source voltage VS.
2 COMP passive Compensation pin for the main boost converter, where a small capacitor and, if required, a resistor is connected.
3 OS input Output sense pin connected to the boost rectifier switch and overvoltage protection comparator; it must connect only to the boost converter output, with a 470-nF capacitor to GND and a wide PCB trace because it conducts high current.
4 SW input Switch pin of the boost converter generating VS.
5 SW input Switch pin of the boost converter generating VS.
6 PGND power_in Power ground; the PowerPAD is connected to PGND.
7 PGND power_in Power ground; the PowerPAD is connected to PGND.
8 SUP input Supply pin of the positive charge pump driver, connected to VIN or to the boost converter output VS depending on the desired VGH and number of charge pump stages.
9 EN2 input Enable for the boost converter and positive charge pump, which start after the buck converter is in regulation and the DLY2 delay has passed; logic high enables and logic low shuts down, and the pin must not be left floating.
10 DRP output Drive pin of the positive charge pump.
11 DRN output Drive pin of the negative charge pump.
12 FREQ input Frequency adjust pin that sets the switching frequency with a logic level: low for 500 kHz and high for 750 kHz.
13 FBN input Feedback pin of the negative charge pump.
14 FBP input Feedback pin of the positive charge pump.
15 FBB input Feedback pin of the buck converter.
16 EN1 input Enable for the buck converter and negative charge pump, with the negative pump starting after the DLY1 delay; logic high enables and logic low shuts down, and the pin must not be left floating.
17 BOOT input Gate drive voltage for the buck converter's N-channel MOSFET, with a capacitor connected from the switch node SWB to this pin.
18 SWB output Switch pin of the buck converter.
19 NC unconnected Not connected.
20 VINB power_in Power input voltage pin for the buck converter.
21 VINB power_in Power input voltage pin for the buck converter.
22 AVIN input Analog input voltage of the device, which should be bypassed with a 1-μF ceramic capacitor for good filtering.
23 GND power_in Analog ground.
24 REF output Internal reference output, typically 1.213 V, which requires a 220-nF capacitor connected to this pin.
25 DLY1 output A capacitor from this pin to GND sets the delay between V(LOGIC) going high and the start-up of VGL.
26 DLY2 output A capacitor from this pin to GND sets the delay between V(LOGIC) going high and the start-up of the VS boost converter and positive charge pump VGH.
27 GD output Gate drive pin for an external MOSFET isolation switch on VS or VGH; it is an open-drain output latched low once the boost converter is within 8% of its nominal output and goes high impedance when EN2 is cycled low.
28 SS output Sets the soft-start time for the main boost converter VS, typically with a 22-nF capacitor connected to this pin.
29 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-28-EP
Category Power Supply Chip
Pins 29

CAD (KiCad official)

  • Symbol: TPS65161PWPR
  • Footprint: Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm
  • 3D model: HTSSOP-28-EP (KiCad packages3D, STEP)
  • 3D model files: tps65161pwpr-etched.step / tps65161pwpr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps65161pwpr.step / tps65161pwpr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (33 pp, sha256 04d74956b7c1cff2, retrieved 2026-10-11, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF