3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTPS65161PWPR
Texas Instruments · Power Management Specialized - PMIC · HTSSOP-28-EP
TPS65161PWPR from Texas Instruments, in a HTSSOP-28-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | FB | input | Feedback input of the main boost converter that generates the source voltage VS. |
| 2 | COMP | passive | Compensation pin for the main boost converter, where a small capacitor and, if required, a resistor is connected. |
| 3 | OS | input | Output sense pin connected to the boost rectifier switch and overvoltage protection comparator; it must connect only to the boost converter output, with a 470-nF capacitor to GND and a wide PCB trace because it conducts high current. |
| 4 | SW | input | Switch pin of the boost converter generating VS. |
| 5 | SW | input | Switch pin of the boost converter generating VS. |
| 6 | PGND | power_in | Power ground; the PowerPAD is connected to PGND. |
| 7 | PGND | power_in | Power ground; the PowerPAD is connected to PGND. |
| 8 | SUP | input | Supply pin of the positive charge pump driver, connected to VIN or to the boost converter output VS depending on the desired VGH and number of charge pump stages. |
| 9 | EN2 | input | Enable for the boost converter and positive charge pump, which start after the buck converter is in regulation and the DLY2 delay has passed; logic high enables and logic low shuts down, and the pin must not be left floating. |
| 10 | DRP | output | Drive pin of the positive charge pump. |
| 11 | DRN | output | Drive pin of the negative charge pump. |
| 12 | FREQ | input | Frequency adjust pin that sets the switching frequency with a logic level: low for 500 kHz and high for 750 kHz. |
| 13 | FBN | input | Feedback pin of the negative charge pump. |
| 14 | FBP | input | Feedback pin of the positive charge pump. |
| 15 | FBB | input | Feedback pin of the buck converter. |
| 16 | EN1 | input | Enable for the buck converter and negative charge pump, with the negative pump starting after the DLY1 delay; logic high enables and logic low shuts down, and the pin must not be left floating. |
| 17 | BOOT | input | Gate drive voltage for the buck converter's N-channel MOSFET, with a capacitor connected from the switch node SWB to this pin. |
| 18 | SWB | output | Switch pin of the buck converter. |
| 19 | NC | unconnected | Not connected. |
| 20 | VINB | power_in | Power input voltage pin for the buck converter. |
| 21 | VINB | power_in | Power input voltage pin for the buck converter. |
| 22 | AVIN | input | Analog input voltage of the device, which should be bypassed with a 1-μF ceramic capacitor for good filtering. |
| 23 | GND | power_in | Analog ground. |
| 24 | REF | output | Internal reference output, typically 1.213 V, which requires a 220-nF capacitor connected to this pin. |
| 25 | DLY1 | output | A capacitor from this pin to GND sets the delay between V(LOGIC) going high and the start-up of VGL. |
| 26 | DLY2 | output | A capacitor from this pin to GND sets the delay between V(LOGIC) going high and the start-up of the VS boost converter and positive charge pump VGH. |
| 27 | GD | output | Gate drive pin for an external MOSFET isolation switch on VS or VGH; it is an open-drain output latched low once the boost converter is within 8% of its nominal output and goes high impedance when EN2 is cycled low. |
| 28 | SS | output | Sets the soft-start time for the main boost converter VS, typically with a 22-nF capacitor connected to this pin. |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-28-EP |
| Category | Power Supply Chip |
| Pins | 29 |
CAD (KiCad official)
- Symbol:
TPS65161PWPR - Footprint:
Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm - 3D model: HTSSOP-28-EP (KiCad packages3D, STEP)
- 3D model files:
tps65161pwpr-etched.step/tps65161pwpr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps65161pwpr.step/tps65161pwpr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (33 pp, sha256
04d74956b7c1cff2, retrieved 2026-10-11, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).