3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownRTL8189ES-VB-CG
Realtek Semicon · RF Transceiver ICs · QFN-32-EP(5x5)
RTL8189ES-VB-CG from Realtek Semicon, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TXPA_OP | output | RF TX positive signal output from the power amplifier. |
| 2 | TXPA_ON | output | RF TX negative signal output from the power amplifier. |
| 3 | VD33PAD | power_in | 3.3V supply for the PAD circuitry. |
| 4 | RXIP | input | RF receive positive signal input. |
| 5 | RXIN | input | RF receive negative signal input. |
| 6 | VD12R | power_in | 1.2V supply for analog circuitry; Table 9 gives the 1.2V core supply range as 1.10 V to 1.32 V. |
| 7 | VD12S | power_in | 1.2V supply for analog circuitry; Table 9 gives the 1.2V core supply range as 1.10 V to 1.32 V. |
| 8 | VD33S | power_in | 3.3V supply for analog circuitry; Table 9 gives the 3.3V I/O supply range as 3.0 V to 3.6 V. |
| 9 | XO | output | Output of the crystal clock reference oscillator. |
| 10 | XI | input | Oscillator input for the crystal clock reference, which can be 40, 13, 19.2, 20, 25, 26, 38.4, 17.664, 16, 14.318 or 12 MHz. |
| 11 | VD33A | power_in | 3.3V supply for analog circuitry; Table 9 gives the range as 3.0 V to 3.6 V. |
| 12 | VD12A | power_in | 1.2V supply for analog circuitry; Table 9 gives the range as 1.10 V to 1.32 V. |
| 13 | VD12D | power_in | 1.2V supply for digital circuitry; Table 9 gives the range as 1.10 V to 1.32 V. |
| 14 | GND_SPS | power_in | Ground for the switching regulator. |
| 15 | LX_SPS | power_out | Switching regulator output node. |
| 16 | VDSPS33 | power_in | Switching regulator input, or linear regulator output from 3.3V to 1.5V, depending on the configuration. |
| 17 | VD33A | power_in | 3.3V supply for analog circuitry; Table 9 gives the range as 3.0 V to 3.6 V. |
| 18 | VDIO_SDIO | power_in | Supply for the SDIO pins; it must match the SDIO bus signal level, which ranges from 3.3V to 1.8V. |
| 19 | SD_D0 | bidirectional | SDIO data line 0; in GSPI mode this pin is SPI_MISO (GSPI data out). |
| 20 | SD_D1 | bidirectional | SDIO data line 1; in GSPI mode this pin is SPI_SCSn (GSPI chip select, active low). |
| 21 | SD_CLK | input | SDIO clock input; in GSPI mode this pin is SPI_CLK. SDIO clock rate is up to 100 MHz per the features list, and Table 13 gives 0-25 MHz default and 0-50 MHz high-speed. |
| 22 | SD_CMD | bidirectional | SDIO command line; in GSPI mode this pin is SPI_MOSI (GSPI data input). |
| 23 | SD_D2 | bidirectional | SDIO data line 2; in GSPI mode this pin is SPI_SIRQ (GSPI interrupt output). |
| 24 | SD_D3 | bidirectional | SDIO data line 3. |
| 25 | PDn | input | Externally shuts down the RTL8189ES-VB without requiring an extra power switch. |
| 26 | GPIO5 | bidirectional | Active-low LED output (LED2), shared with GPIO5 and CLK_REQ, which is used by the chip to request the system clock from the host; the function is selected via a control register. |
| 27 | GPIO7 | bidirectional | General-purpose input/output pin. |
| 28 | GPIO4 | bidirectional | General-purpose input/output pin. |
| 29 | GPIO1 / SPS_LDO_SEL | bidirectional | General-purpose input/output pin; trap function: weakly pull low to enable the integrated switching regulator, or weakly pull high to enable the integrated linear regulator. |
| 30 | VD33IO | power_in | 3.3V supply for digital I/O; Table 9 gives the range as 3.0 V to 3.6 V (Table 9 labels this supply VD33D). |
| 31 | VD12D | power_in | 1.2V supply for digital circuitry; Table 9 gives the range as 1.10 V to 1.32 V. |
| 32 | GPIO6 / TEST_MODE_SEL | bidirectional | General-purpose input/output pin; trap function: weakly pull low to let the chip enter normal operation mode. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Realtek Semicon |
| Package | QFN-32-EP(5x5) |
| Category | RF & Radio |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Clock Low Time | TWL | 10 | ns | Default mode | 10 | ||
| Clock Low Time | TWL | 7 | ns | HS mode | 10 | ||
| Clock High Time | TWH | 10 | ns | Default mode | 10 | ||
| Clock High Time | TWH | 7 | ns | HS mode | 10 | ||
| Input Setup Time | TISU | 5 | ns | Default mode | 10 | ||
| Input Setup Time | TISU | 6 | ns | HS mode | 10 | ||
| Input Hold Time | TIH | 5 | ns | Default mode | 10 | ||
| Input Hold Time | TIH | 2 | ns | HS mode | 10 | ||
| Output Delay Time | TODLY | 14 | ns | Default mode | 10 | ||
| Tpor | Tpor | 2 | 2 | 8 | ms | SDIO power-on typical timing specification | 11 |
| Tnon-rdy | Tnon-rdy | 1 | 2 | 10 | ms | SDIO power-on typical timing specification | 11 |
CAD (KiCad official)
- Symbol:
RTL8189ES-VB-CG - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
rtl8189es-vb-cg-etched.step/rtl8189es-vb-cg-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);rtl8189es-vb-cg.step/rtl8189es-vb-cg.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Realtek Semicon datasheet (19 pp, sha256
44ad30d46d987eb5, retrieved 2026-11-05, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).